Search NASA⌕ Search

Engineering topics

Dejarnette, F. R.

Publications and source records attributed to Dejarnette, F. R..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

Approximate method for calculating heating rates on three-dimensional vehicles

An approximate method for calculating heating rates on three-dimensional vehicles at angle of attack is presented. The method is based on the axisymmetric analog for three-dimensional boundary layers and uses a generalized body-fitted coordinate system. Edge conditions for the boundary-layer solution are obtained from an inviscid flowfield solution, and because of the coordinate system used, the method is applicable to any blunt body geometry for which an inviscid flowfield solution can be obtained. The method is validated by comparing with experimental heating data and with thin-layer Navier-Stokes calculations on the shuttle orbiter at both wind-tunnel and flight conditions and with thin-layer Navier-Stokes calculations on the HL-20 at wind-tunnel conditions.

Hamilton, H. Harris↗
NASA NTRS1992

An approximate viscous shock layer technique for calculating nonequilibrium hypersonic flows about blunt-nosed bodies

An approximate axisymmetric method has been developed which can reliably calculate nonequilibrium fully viscous hypersonic flows over blunt-nosed bodies. By substituting Maslen's second-order pressure expression for the normal momentum equation, a simplified form of the viscous shock layer (VSL) equations is obtained. This approach can solve both the subsonic and supersonic regions of the shock layer without a starting solution for the shock shape. This procedure is significantly faster than the parabolized Navier-Stokes and VSL solvers and would be useful in a preliminary design environment. Solutions have been generated for air flows over several analytic body shapes. Surface heat transfer and pressure predictions are comparable to VSL results. Computed heating rates are in good agreement with experimental data. The present technique generates its own shock shape as part of its solution, and therefore could be used to provide more accurate initial shock shapes for higher-order procedures which require starting solutions.

Cheatwood, F. M.↗
NASA NTRS1991

An approximate viscous shock layer approach to calculating hypersonic flows about blunt-nosed bodies

An approximate axisymmetric method has been developed which can reliably calculate fully viscous hypersonic flows over blunt-nosed bodies. By substituting Maslen's second order pressure expression for the normal momentum equation, a simplified form of the viscous shock layer (VSL) equations is obtained. This approach can solve both the subsonic and supersonic regions of the shock layer without a starting solution for the shock shape. Since the method is fully viscous, the problems associated with coupling a boundary-layer solution with an inviscid-layer solution are avoided. This procedure is significantly faster than the parabolized Navier-Stokes (PNS) or VSL solvers and would be useful in a preliminary design environment. Problems associated with a previously developed approximate VSL technique are addressed. Surface heat transfer and pressure predictions are comparable to both VSL results and experimental data. The present technique generates its own shock shape as part of its solution, and therefore could be used to provide more accurate initial shock shapes for higher-order procedures which require starting solutions.

Cheatwood, F. MCN.↗
NASA NTRS1990

Experimental investigation of a new device to control the asymmetric flowfield on forebodies at large angles of attack

An exploratory experimental investigation of a new device to control the asymmetric flowfield on forebodies at large angles of attack has been conducted. The device is a rotatable forebody tip, which varies in cross section from circular at its base to elliptic at its tip. The device itself extends over a small portion of the aircraft or missile forebody. The device provides two important improvements. First, it replaced the normally random behavior of the nose side force as a function of nose tip orientation with a predictable and generally sinusoidal distribution and, second, the device showed promise for use as part of a vehicle control system, to be deflected in a prescribed manner to provide additional directional control for the vehicle. The device was tested on a cone/cylinder model having a 10 deg semiapex angle and on a 3.0 caliber tangent ogive model, each with a base diameter of 3.5 in, for angles of attack from 30 to 60 deg. Data were taken from 3 circumferential rows of pressure taps on each model at a Reynolds number of 84,000 based on cylinder diameter and by a helium-bubble flow visualization technique at a Reynolds number of 24,000.

Moskovitz, Cary A.↗
NASA NTRS1989

An approximate viscous shock layer method for calculating the hypersonic flow over blunt-nosed bodies

The approximate axisymmetric method presented for accurately calculating the surface and flowfield properties of fully viscous hypersonic flow over blunt-nosed bodies incorporates the turbulence model of Cebeci-Smith (1970) and the equilibrium air tables of Hansen (1959). The method is faster than the parabolized Navier-Stokes or viscous shock layer solvers that it could replace for preliminary design determinations. Surface heat transfer and pressure predictions for the present method are comparable with the more accurate viscous shock layer method as well as flight test and wind tunnel data. A starting solution is not required.

Grantz, A. C.↗
NASA NTRS1989

Effects of nose bluntness, roughness, and surface perturbations on the asymmetric flow past slender bodies at large angles of attack

The effects of such geometric perturbations as variations of model-tip sharpness and roughness, as well as discrete surface perturbations, on the asymmetric flow past slender bodies is experimentally investigated for the cases of a cone/cylinder model having a 10-deg semiapex angle and a 3.0-caliber tangent ogive model. Both models have base diameters of 3.5 inches, and were tested in laminar flow conditions at angles-of-attack in the 30-60 deg range. Single, discrete roughness elements were represented by beads; bead effectiveness was judged on the basis of the extent to which they affected the flowfield in various conditions.

Moskovitz, Cary A.↗
NASA NTRS1987

A finite-difference outer layer and integral inner layer method for the solution of the turbulent boundary layer equations

A new turbulent boundary-layer method is developed which models the inner region with the law of the wall while the outer region uses Clauser's eddy viscosity in Matsuno's finite-difference method. The match point between the inner and outer regions as well as the wall shear stress are determined at each marching step during the computation. Results obtained for incompressible, two-dimensional flow over flat plates and ellipses are compared with solutions from a baseline method which uses a finite-difference method for the entire boundary layer. Since the present method used the finite-difference method in the outer region only, the number of grid points required was about half that needed for the baseline method. Accurate displacement and momentum thicknesses were predicted for all cases. Skin friction was predicted well for the flat plate, but the accuracy decreased significantly for the ellipses. Adding a wake functions to the law of the wall allows some of the pressure gradient effect to be taken into account thereby increasing the accuracy of the method.

Barnwell, R. W.↗
NASA NTRS1986

A direct and inverse boundary layer method for subsonic flow over delta wings

A new inverse boundary layer method is developed and applied to incompressible flows with laminar separation and reattachment. Test cases for two dimensional flows are computed and the results are compared with those of other inverse methods. One advantage of the present method is that the calculation of the inviscid velocities may be determined at each marching step without having to iterate. The inverse method was incorporated with the direct method to calculate the incompressible, conical flow over a slender delta wing at incidence. The location of the secondary separation line on the leeward surface of the wing is determined and compared with experiment for a unit aspect ratio wing at 20.5 deg incidence. The viscous flow in the separated region was calculated using prescribed skin friction coefficients.

Woodson, S. H.↗
NASA NTRS1985

A three-dimensional boundary-layer method for flow over delta wings with leading-edge separation

A three-dimensional, laminar boundary-layer method is applied to the incompressible flow over a slender delta wing at incidence. The predictor-corrector finite-difference scheme of Matsuno is used to difference the governing equations. The method has the advantages that no iterations are required to advance the solution and the cross-flow derivatives are formed independent of the cross-field direction. The difference scheme is demonstrated to yield accurate numerical results when compared to the exact solution of the three-dimensional boundary-layer equations for parabolic flow over a moving flat plate. The method is applied to delta wings of various sweep angles at angles of attack up to 20 deg., with the inviscid solution determined using a higher-order, three-dimensional panel method.

Woodson, S. H.↗
NASA NTRS1985

A review of some approximate methods used in aerodynamic heating analyses

It is pointed out that preliminary design and optimization studies for new aerospace vehicles require techniques which can calculate aerodynamic heating rates accurately and efficiently. The method employed to calculate the flow field depends to a large extent on the shape of the vehicle, Mach number, Reynolds number, and Knudsen number. In the case of the aero-assisted orbital transfer vehicle (AOTV), a substantial portion of the flight will be in the transitional regime between continuum and free molecule flow. The present paper discusses some approximate methods which have been used to calculate heating rates on high-speed vehicles. Attention is given to the stagnation point and leading edges, the downstream region, the axisymmetric analog, laminar and turbulent heating rates, transition heating rates, gas models, and three-dimensional applications.

Dejarnette, F. R.↗
NASA NTRS1985

Application of axisymmetric analogue for calculating heating in three-dimensional flows

A rapid, approximate method has been developed for calculating the heating rates on three-dimensional vehicles such as the Space Shuttle Orbiter and other advanced reentry configurations. The method is based on the axisymmetric analogue for three-dimensional boundary layers. It uses information obtained from a three-dimensional inviscid flowfield solution, such as HALIS, to calculate inviscid surface streamlines along which approximate heating rates are calculated independent of what happens along other streamlines. Three-dimensional effects are included through the metric coefficient that describes the divergence or convergence of streamlines. Boundary-layer edge properties are obtained from the inviscid flowfield solution by interpolating in the inviscid flowfield at a distance equal to the boundary-layer thickness away from the wall. This accounts, approximately, for the variable boundary-layer edge entropy. Using this method, heating calculations can be made along a typical streamline in a few seconds. This method has been used to accurately predict heating rates for simple shapes such as a spherically blunted cone and more complex shapes such as the Shuttle Orbiter for a variety of wind-tunnel and flight conditions. A unique feature of the method is its ability to accurately predict heating rates on the Shuttle Orbiter wing.

Hamilton, H. H.↗
NASA NTRS1984

Effects of aircraft and flight parameters on energy-efficient profile descents in time-based metered traffic

The influence of several parameters on the time required to fly a nominal profile descent of a B-737 from an entry fix to a metering fix 75 n.mi. away was studied. The ground distance for the constant speed segment was adjusted in each case so that the aircraft would always arrive at the metering fix position at the completion of the five segments of the profile descent. The influence of eight parameters on the same nominal profile descent is outlined, but the method used for the off nominal cases was changed. The time calculated for the constant speed segment in the nominal case is used for all off nominal cases. This method allows the aircraft to arrive at the metering fix before or after the profile descent is complete. It is shown that descent Mach number and wind speed have a large effect on the time error, whereas weight was a much smaller effect.

Dejarnette, F. R.↗
NASA NTRS1984

Numerical and experimental determination of secondary separation on delta wings in subsonic flow

A quasi-three-dimensional boundary layer method for conical inviscid flows is presented. The model was developed to characterize the flow fields over slender delta wings, particularly the shed vortex sheet. A steady, incompressible, laminar boundary layer is assumed and a solution is obtained with the Smith (1966) finite difference code. Predictions are compared with oil flow patterns and surface pressure measurements for 74 and 80 deg delta wings at 0-20 deg angles of attack. The model is capable of accurately predicting the secondary separation lines. Inviscid velocities derived from panel methods lead, however, to inaccurate pressure distributions.

Dejarnette, F. R.↗
NASA NTRS1984

Effects of aircraft and flight parameters on energy-efficient profile descents in time-based metered traffic

Concepts to save fuel while preserving airport capacity by combining time based metering with profile descent procedures were developed. A computer algorithm is developed to provide the flight crew with the information needed to fly from an entry fix to a metering fix and arrive there at a predetermined time, altitude, and airspeed. The flight from the metering fix to an aim point near the airport was calculated. The flight path is divided into several descent and deceleration segments. Descents are performed at constant Mach numbers or calibrated airspeed, whereas decelerations occur at constant altitude. The time and distance associated with each segment are calculated from point mass equations of motion for a clean configuration with idle thrust. Wind and nonstandard atmospheric properties have a large effect on the flight path. It is found that uncertainty in the descent Mach number has a large effect on the predicted flight time. Of the possible combinations of Mach number and calibrated airspeed for a descent, only small changes were observed in the fuel consumed.

Dejarnette, F. R.↗