Search NASA⌕ Search

Engineering topics

Delzeit, Lance

Publications and source records attributed to Delzeit, Lance.

At least 19 records

BioMoSS: Biocidal MoS2 for Disinfection of Spacecraft Potable Water Systems

It has been reported in the literature that few-layered, vertically-aligned molybdenum disulfide (FLV-MoS2) can produce biocidal agents for water disinfection with great effectiveness under visible light excitation. The nano-structure, with limited layers and small domain size increases the band gap of the MoS2 in the visible region such that visible light can be used to drive the production of reactive oxygen species (ROS) for biocidal control. This paper will present the BioMoSS (biocidal MoS2) for space applications concept and present initial results of the investigation into turning the FLV-MoS2 into a viable biocidal system.

Delzeit, Lance↗

Mitigation of Silver Ion Loss from Solution by Polymer Coating of Metal Surfaces

Spacecraft potable water systems require a biocidal agent that effectively provides both immediate and residual disinfection over long periods of time. Ionic silver (Ag+) is a leading candidate for this application, but suffers from rapid concentration loss due interactions with the metal storage containers and tubing. In order to maintain biocidal efficacy in systems with long periods of dormancy and to reduce the required rate of Ag+ injection, it is necessary to develop alternative materials and coatings for certified metal alloys that significantly reduce the Ag+ loss. In this work, we investigate the performance of two unusual polymers, Teflon AF 2400 and parylene-AF4, as barrier coatings under immersion in 400 ppb Ag+. We show that 25 m-thick parylene-AF4 is a promising coating with Ag+ losses similar to PTFE. Key challenges with this material include maintenance of adhesion under long-term immersion and control of deposition during the internal coating of high-aspect ratio tubing. Solutions to these problems may including surface structuring of substrates for mechanical anchoring or an alternative parylene-C chemistry (with more stable adhesion), and dynamic spatio-temporal control of substrate temperature, respectively.

water↗

Chromium Brine Containment Membrane Demister for the CapiBRiC

The development of a microgravity air-evaporation urine brine dryer (CapiBRiC - Capillary Brine Residual in Containment) that releases its effluent gas into the cabin of the International Space Station will require some form of a demister to guarantee that no acid, chromium, or other hazardous materials are released within the effluent gas stream. A hydrophobic membrane demister can be used for this application, and can be compatible with the proposed high flow rates of the effluent gas stream. This paper will describe the construction and sizing of such a membrane demister.

CapiBRiC↗

Results of the FY15 Brine Evaporation Bag (BEB) Technology Down-Select Testing

The Brine Evaporation Bag (BEB) recently participated in the Brine Concentrator Technology (BCT) Technology Down-Select (TDS). It was found that the BEB System is able to process ISS (International Space Station) Alternate Pretreat Brine at a rate high enough for ISS application as well as future deep space missions. The BEB System is also capable of processing the brine to a solid residue which will add to the stability and safety of storing the brine residue. The results of the BEB testing for the BCT-TDS will be presented in this paper.

recycling↗

Development of the Continuous-Fill Brine Evaporation Bag (BEB) System

The existing water recovery system on the International Space Station (ISS) is limited to 70 percent reclamation; consequently, long duration space missions are currently unfeasible due to the large quantity of water necessary to sustain the crew. The Brine Evaporation Bag (BEB) is a proposed system to supplement the existing water recovery system aboard the ISS and future deep space missions that can increase water recovery to 99 percent. The BEB project previously focused on the development of only the bag portion of the system. This paper focuses on the development of the BEB Evaporator. It will discuss the work to understand, optimize, and improve the entire BEB system while implementing a continuous-fill process. The results of that development and the advantages and limitations of the continuous-fill process will be presented.

Water Recovery↗

Results of the FY15 Brine Evaporation Bag (BEB) Technology Down-Select Testing

The Brine Evaporation Bag (BEB) recently participated in the Brine Concentrator Technology (BCT) Technology Down-Select (TDS). It was found that the BEB System is able to process ISS (International Space Station) Alternate Pretreat Brine at a rate high enough for ISS application as well as future deep space missions. The BEB System is also capable of processing the brine to a solid residue which will add to the stability and safety of storing the brine residue. The results of the BEB testing for the BCT-TDS will be presented in this paper.

Delzeit, Lance↗

Development of the Auto-Fill Brine Evaporation Bag (BEB) System

The existing water recovery system on the International Space Station (ISS) is limited to 70 percent reclamation; consequently, long duration space missions are currently unfeasible due to the large quantity of water necessary to sustain the crew. The Brine Evaporation Bag (BEB) is a proposed system to supplement the existing water recovery system aboard the ISS and future deep space missions that can increase water recovery to 99 percent. The BEB project previously focused on the development of only the bag portion of the system. This paper focuses on the development of the BEB Evaporator. It will discuss the work to understand, optimize, and improve the entire BEB system while implementing a continuous-fill process. The results of that development and the advantages and limitations of the continuous-fill process will be presented.

Delzeit, Lance↗

Results for the Brine Evaporation Bag (BEB) Brine Processing Test

The recent Brine Processing Test compared the NASA Forward Osmosis Brine Dewatering (FOBD), Paragon Ionomer Water Processor (IWP), UMPQUA Ultrasonic Brine Dewatering System (UBDS), and the NASA Brine Evaporation Bag (BEB). This paper reports the results of the BEB. The BEB was operated at 70 deg C and a base pressure of 12 torr. The BEB was operated in a batch mode, and processed 0.4L of brine per batch. Two different brine feeds were tested, a chromic acid-urine brine and a chromic acid-urine-hygiene mix brine. The chromic acid-urine brine, known as the ISS Alternate Pretreatment Brine, had an average processing rate of 95 mL/hr with a specific power of 5kWhr/L. The complete results of these tests will be reported within this paper.

BEB↗

Results of the GCMS Effluent Gas Analysis for the Brine Processing Test

The effluent gas for the Paragon Ionomer Water Processor (IWP), UMPQUA Ultrasonic Brine Dewatering System (UBDS), and the NASA Brine Evaporation Bag (BEB) were analyzed using Headspace GCMS Analysis in the recent AES FY14 Brine Processing Test. The results from the analysis describe the number and general chemical species of the chemicals produced. Comparisons were also made between the different chromatograms for each system, and an explanation of the differences in the results is reported.

GCMS↗

Evaluation of Brine Processing Technologies for Spacecraft Wastewater

Brine drying systems may be used in spaceflight. There are several advantages to using brine processing technologies for long-duration human missions including a reduction in resupply requirements and achieving high water recovery ratios. The objective of this project was to evaluate four technologies for the drying of spacecraft water recycling system brine byproducts. The technologies tested were NASA's Forward Osmosis Brine Drying (FOBD), Paragon's Ionomer Water Processor (IWP), NASA's Brine Evaporation Bag (BEB) System, and UMPQUA's Ultrasonic Brine Dewatering System (UBDS). The purpose of this work was to evaluate the hardware using feed streams composed of brines similar to those generated on board the International Space Station (ISS) and future exploration missions. The brine formulations used for testing were the ISS Alternate Pretreatment and Solution 2 (Alt Pretreat). The brines were generated using the Wiped-film Rotating-disk (WFRD) evaporator, which is a vapor compression distillation system that is used to simulate the function of the ISS Urine Processor Assembly (UPA). Each system was evaluated based on the results from testing and Equivalent System Mass (ESM) calculations. A Quality Function Deployment (QFD) matrix was also developed as a method to compare the different technologies based on customer and engineering requirements.

recycling↗

Continued Development of the Brine Evaporation Bag

The Brine Evaporation Bag (BEB) is a membrane-based bag system for the dewatering of brine. Previous studies showed the ability of the BEB to dewater brine at low temperatures with a 96 percent mass reduction. Additionally, a microgravity flight showed the BEB is microgravity compatible. Current work focuses on the effects of temperature, vacuum, purge gas flow rate, membrane area, and membrane permeability on the rate of dewatering within a vacuum oven configured to mimic the Heat Melt Compactor. Within this study, it was found that changing the temperature or level of vacuum would change the rate of dewatering. The purge gas, membrane area, and membrane permeability did not affect the dewater rate. The reason for this behavior may be that the dewatering is heat transfer limited, and out of all the parameters studied, only the temperature and vacuum have an effect on the heat transfer rate. The ISS (International Space Station) produces brine at a rate of 1.2 liters per day. This initial study showed that it is possible to remove water from a BEB at a rate of 1.6 liters per day in this breadboard configuration; even at moderate temperatures. Development of a dedicated BEB Evaporator will be discussed. In addition, it is further postulated that a specifically designed BEB Evaporator would result in an increased dewatering rate allowing for even lower operating temperatures or faster dewatering rates.

Recycling↗

Directed Growth of Carbon Nanotubes Across Gaps

An experiment has shown that when single-walled carbon nanotubes (SWNTs) are grown by chemical vapor deposition in the presence of an electric field of suitable strength, the nanotubes become aligned along the electric field. In an important class of contemplated applications, one would exploit this finding in fabricating nanotube transistors; one would grow SWNTs across gaps between electrodes that would serve, subsequently, as source and drain contacts during operation of the transistors. In preparation for the experiment, a multilayer catalyst comprising a 20-nmthick underlayer of iridium (platinum group), a 1-nm-thick middle layer of iron, and a 0.2-nm-thick outer layer of molybdenum was ion-beam sputtered onto a quartz substrate. A 25 micrometers-diameter iron wire was used as a shadow mask during the sputtering to create a 25 micrometers gap in the catalyst. Then electrical leads were connected to the catalyst areas separated by the gap so that these catalyst areas would also serve as electrodes. The substrate as thus prepared was placed in a growth chamber that consisted of a quartz tube of 1-in. (2.54-cm) diameter enclosed in a furnace. SWNTs of acceptably high quantity and quality were grown in 10 minutes with methane at atmospheric pressure flowing through the chamber at a rate of 1,000 standard cubic centimeters per minute at a temperature of 900 C. To prevent oxidation of the SWNTs, the chamber was purged with 99.999-percent pure argon before and after growth, and the chamber was cooled to less than 300 C before opening it to the atmosphere after growth. When no voltage was applied across the gap, the SWNTs grew in random directions extending out from the edges of the catalyst at the gap. When a potential of 10 V was applied between the catalyst/electrode areas to create an electric field across the gap, the SWNTs grew across the gap, as shown in the figure.

Delzeit, Lance↗

Multiwalled Carbon Nanotube/nanofiber Arrays as Conductive and Dry Adhesive Interface Materials

We demonstrate the possibility of making conductive and dry adhesive interfaces between multiwalled carbon nanotube (MWNT) and nanofiber (MWNF) arrays grown by chemical vapor deposition with transition-metal as catalyst on highly Boron doped silicon substrates. The maximum observed adhesion force between MWNT and MWNF surfaces is 3.5 mN for an apparent contact area of 2 mm by 4 mm. The minimum contact resistance measured at the same time is approx.20 Omega. Contact resistances of MWNT-MWNT and MWNT-gold interfaces were also measured as pressure forces around several mN were applied at the interface. The resulting minimum contact resistances are on the same order but with considerable variation from sample to sample. For MWNT-MWNT contacts, a minimum contact resistance of approx.1 Omega is observed for a contact area of 2 mm by 1 mm. The relatively high contact resistances, considering the area density of the nanotubes, might be explained by the high cross-tube resistances at the contact interfaces.

Tong, Tao↗

CVD Growth of Carbon Nanotubes: Structure, Catalyst, and Growth

Carbon nanotubes (CNTs) exhibit extraordinary mechanical and unique electronic properties and hence have been receiving much attention in recent years for their potential in nanoelectronics, field emission devices, scanning probes, high strength composites and many more applications. Catalytic decomposition of hydrocarbon feedstock with the aid of supported transition metal catalysts - also known as chemical vapor deposition (CVD) - has become popular to produce single-walled and multi-walled nanotubes (SWNTs, MWNTs) and multiwalled nanofibers (MWNFs). The ability to grow CNTs on patterned substrates and in vertically aligned arrays, and the simplicity of the process, has made CVD growth of CNTs an attractive approach.

Delzeit, Lance↗

Development of Metal-impregnated Single Walled Carbon Nanotubes for Toxic Gas Contaminant Control in Advanced Life Support Systems

The success of physico-chemical waste processing and resource recovery technologies for life support application depends partly on the ability of gas clean-up systems to efficiently remove trace contaminants generated during the process with minimal use of expendables. Highly purified metal-impregnated carbon nanotubes promise superior performance over conventional approaches to gas clean-up due to their ability to direct the selective uptake gaseous species based both on the nanotube s controlled pore size, high surface area, and ordered chemical structure that allows functionalization and on the nanotube s effectiveness as a catalyst support material for toxic contaminants removal. We present results on the purification of single walled carbon nanotubes (SWCNT) and efforts at metal impregnation of the SWCNT's.

Cinke, Martin↗

Plasma-enhanced chemical vapor deposition of multiwalled carbon nanofibers

Plasma-enhanced chemical vapor deposition is used to grow vertically aligned multiwalled carbon nanofibers (MWNFs). The graphite basal planes in these nanofibers are not parallel as in nanotubes; instead they exhibit a small angle resembling a stacked cone arrangement. A parametric study with varying process parameters such as growth temperature, feedstock composition, and substrate power has been conducted, and these parameters are found to influence the growth rate, diameter, and morphology. The well-aligned MWNFs are suitable for fabricating electrode systems in sensor and device development.

Nanotechnology/instrumentation/methods↗

The Surface Interface Characteristics of Vertically Aligned Carbon Nanotube and Graphitic Carbon Fiber Arrays Grown by Thermal and Plasma Enhanced Chemical Vapor Deposition

The development of nano-arrays for sensors and devices requires the growth of arrays with the proper characteristics. One such application is the growth of vertically aligned carbon nanotubes (CNTs) and graphitic carbon fibers (GCFs) for the chemical attachment of probe molecules. The effectiveness of such an array is dependent not only upon the effectiveness of the probe and the interface between that probe and the array, but also the array and the underlaying substrate. If that array is a growth of vertically aligned CNTs or GCFs then the attachment of that array to the surface is of the utmost importance. This attachment provides the mechanical stability and durability of the array, as well as, the electrical properties of that array. If the detection is to be acquired through an electrical measurement, then the appropriate resistance between the array and the surface need to be fabricated into the device. I will present data on CNTs and GCFs grown from both thermal and plasma enhanced chemical vapor deposition. The focus will be on the characteristics of the metal film from which the CNTs and GCFs are grown and the changes that occur due to changes within the growth process.

Delzeit, Lance↗

Plasma CVD of Carbon Nanotubes

Carbon nanotubes(CNT) exhibit remarkable mechanical and unique electronic properties and thus have created excitement in the research community about their potential in electronics, computing, sensor and structural applications. Realization of these applications critically depends on the ability to control the properties(such as diameter, chirality) as well purity. We have investigated CNT growth using an inductively coupled plasma(ICP) process using hydrocarbon feedstock. The catalyst required for nanotube growth consists of thin sputtered layers of aluminum and iron(10 nm each) and aligned carbon nanotubes have been obtained. Optical emission diagnostics as well as a plasma modeling effort have been undertaken to understand growth mechanisms. This presentation will discuss growth characteristics under various pressure, power and feedgas compositions and our understanding from modeling and diagnostics.

Delzeit, Lance↗