Search NASA⌕ Search

Engineering topics

Demkowicz, M. J.

Publications and source records attributed to Demkowicz, M. J..

7 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Near-Surface Layer Perforations as Precursors to Fracture in Accumulative Roll Bonding of a Multilayered Metal Composite

We use micro-computed tomography (µ-CT) to characterize the sizes, shapes, and locations of layer perforation (LP) defects in laminates of copper (Cu) and tantalum (Ta) processed by accumulative roll bonding (ARB). One—termed Cu/Ta—was processed from an initial stacking of seven alternating Cu and Ta sheets, with the exterior sheets being Cu. In the other—termed Ta/Cu—the exterior sheets are Ta. Cu/Ta remained intact during processing and exhibits an approximately uniform spatial distribution of LPs. By contrast, Ta/Cu fractured by longitudinal splitting. LPs in this latter sample are concentrated near the sample surfaces. Moreover, their density increases with decreasing distance to the fracture surface. Furthermore, these findings show that materials undergoing ARB may remain intact, despite profuse formation of LPs, provided that the LPs are uniformly distributed. However, a non-uniform distribution of LPs is correlated with longitudinal splitting.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Quasi-static and dynamic response of a Cu/Nb composite following equal channel angular extrusion

The article presents a study of the plastic properties of a Cu–18%Nb composite following equal channel angular extrusion under both low- and high-strain rate loadings. The microstructures are characterized by optical and scanning electron microscopy as well as electron backscatter diffraction. Comparisons are also made with a Cu–50%Nb laminate made by accumulative roll bonding. Textures obtained within the respective phases in the extruded composite closely mimic those previously reported for the pure components alone (Cu, Nb). Grain sizes of the major phase (Cu) exhibit broad distributions, due largely to partial recrystallization during the extrusion process. Further re-crystallization is obtained within localized deformation bands produced at high strain rates (3 × 10 3 s –1 ). While the degree of anisotropy and the strain rate sensitivity of the composite response are similar to those of pure Cu after extrusion, the strength levels of the composite are somewhat greater, falling broadly between those obtained in the pure components after extrusion to comparable plastic strains. Furthermore, the implications for selection of composite composition and processing for achieving higher strengths are briefly discussed.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Shear strain alters the structure and migration mechanism of self-interstitial atoms in copper

Here, we use atomistic modeling to show that externally applied shear strain causes the lowest energy self-interstitial atom (SIA) structure in copper (Cu) to change from a <100>-type dumbbell to a <110>-type dumbbell. Concurrently, SIA migration switches from the 3-D random walk characteristic of <100>-type dumbbells to a 1-D mechanism analogous to that of crowdion SIAs. Furthermore, the relative energies of these two dumbbell structures as a function of strain are well predicted using elastic dipole tensors computed at zero strain, indicating that examination of these tensors may be used to assess the likelihood of strain-induced SIA structure transitions in other materials. Changes in lowest energy SIA structures and associated migration mechanisms stand to impact predictions of SIA behavior in irradiated solids.

36 MATERIALS SCIENCE↗
DOE OSTI2016

Non-random walk diffusion enhances the sink strength of semicoherent interfaces

Clean, safe and economical nuclear energy requires new materials capable of withstanding severe radiation damage. One strategy of imparting radiation resistance to solids is to incorporate into them a high density of solid-phase interfaces capable of absorbing and annihilating radiation-induced defects. Here we show that elastic interactions between point defects and semicoherent interfaces lead to a marked enhancement in interface sink strength. Our conclusions stem from simulations that integrate first principles, object kinetic Monte Carlo and anisotropic elasticity calculations. Surprisingly, the enhancement in sink strength is not due primarily to increased thermodynamic driving forces, but rather to reduced defect migration barriers, which induce a preferential drift of defects towards interfaces. The sink strength enhancement is highly sensitive to the detailed character of interfacial stresses, suggesting that ‘super-sink’ interfaces may be designed by optimizing interface stress fields. Lastly, such interfaces may be used to create materials with unprecedented resistance to radiation-induced damage.

36 MATERIALS SCIENCE↗