Search NASA⌕ Search

Engineering topics

Denis-Gabriel Caprace

Publications and source records attributed to Denis-Gabriel Caprace.

6 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Simulation of a Single Rotor and a Quadrotor Hovering in Full and Partial Ground Effect

With the development of urban air mobility, the safety of multirotor vehicle operations in proximity to vertiports must be assessed. This paper examines high-fidelity blade-resolved OVERFLOW simulations and medium-fidelity vortex particle–mesh simulations that capture the aerodynamics of a rotorcraft in full and partial ground effect. Results obtained with each CFD method are compared to verify the consistency of the models introduced in the latter, which include an immersed lifting line for the blade aerodynamics and various boundary conditions to account for solid surfaces such as ground and walls. Satisfactory agreement is obtained for the blade loads and rotorwash velocity profiles in the case of a single rotor, except for small discrepancies at the blade tip. Finally, a quadrotor air taxi is simulated to quantify the load imbalance when the vehicle hovers above a rooftop edge. The combined use of high- and medium-fidelity methods is envisioned to accelerate the workflow when a large number of configurations need to be tested.

HEC↗
NASA NTRSDate not supplied

Simulation of the Rotorwash Induced by a Quadrotor Urban Air Taxi in Ground Effect

A rotorcraft hovering near the ground causes downwash and outwash. The impact of these induced velocities on urban air mobility operations has not been extensively quantified. This paper explores the opportunity of using CFD to perform dedicated studies on the aerodynamics of rotorcraft in ground effect (IGE). For this purpose, we compare load and flow predictions obtained with the high-fidelity CFD solver OVERFLOW and with a medium-fidelity vortex particle-mesh (VPM) method, for a single rotor IGE. We show that the computational cost of high-fidelity simulation makes it impractical to sweep through a large number of configurations or operating conditions. However, a small set of cases can be used to verify a medium-fidelity tool. The latter provides a better trade-off between “accuracy” and computational intensity, which enables numerous, longer simulations at a more affordable cost. As an example, the outwash flow is computed for two different designs of a quadrotor air taxi in hover and reveals the existence of increased velocities between the rotors. This work illustrates how CFD can help identify dangerous areas for passengers and ground personnel when they approach the vehicle.

HECC↗
NASA NTRSDate not supplied

Comparing Planetary Helicopter Brownout Observations with Numerical Predictions for Ingenuity

Ingenuity is considered the Martian equivalent of the Wright Flyer. Its sustained flights on Mars proved that non-terrestrial powered flight is possible, even on planets with thin atmospheres. However, Ingenuity was small and carried no payload. Future planetary rotorcraft will be bigger and heavier to accomplish new scientific and exploratory goals. On dusty planets, the associated increase in rotor thrust poses a potential challenge well known to helicopter pilots who have flown in desert environments: dust clouds forming during take-off and landing due to rotor wash, referred to as brownout. This work evaluates the effectiveness of existing numerical simulation models in predicting the severity of this phenomenon for planetary rotorcraft. We compare the output of a CFD-based dust mobilization model with data recently gathered using image processing techniques of Ingenuity’s flights. The simulation results suggest that the sensitivity of the wall friction velocity to the rotorcraft height may be lower than previously assessed. We further evaluate the sensitivity of the total mass of mobilized dust to other model parameters such as the sandblasting efficiency and the saltation threshold velocity. Finally, we discuss the limitations of this comparison due to uncertainty in both the observation and the numerical model.

HEC↗
NASA NTRSDate not supplied

Comparing Methods to Extract Sectional Angle of Attack From Blade-Resolved Rotor Simulations

The angle of attack is widely used to describe the aerodynamics of rotor blades. Models based on lifting lines, actuator lines, and actuator disks use it as a primary variable, assuming the aerodynamics can be represented by the flow around a collection of equivalent 2D airfoils. This paper evaluates the accuracy of existing methods that extract the angle of attack from blade-resolved CFD simulations, towards enabling a direct comparison of angle of attack between blade-resolved and blade-modeled simulations. Results are compared for a 2D airfoil for which the angle of attack is known by definition. The hovering rotor case is also considered, where we look at two different rotor blades. We discuss the factors that impact the accuracy of the 2D predictions. For the 3D rotors, we show that three-dimensional effects in the root and tip regions lead to large discrepancies between methods. This suggests that the very definition of angle of attack is unable to accurately represent the flow in these regions. Finally, based on guidelines that we establish, we propose an alternate method that uses local velocities sampled on a contour located 0.25 chord, or less, away from the airfoil surface and generally yields improved accuracy compared to most existing techniques.

ARMD↗