Search NASA⌕ Search

Engineering topics

Detrois, Martin

Publications and source records attributed to Detrois, Martin.

At least 73 records · Page 4

Partitioning of tramp elements Cu and Si in a Ni-based superalloy and their effect on creep properties

An alloy's processing history, including melting, remelting or the choice of stock material, affects its purity and eventually involves tramp element pickup or retention. Herein, variants of a novel Ni-based superalloy were manufactured with different levels of purity. The so-called low purity alloys contained 0.138 wt. % Cu and 0.019 wt. % Si while the Cu and Si levels were below x-ray fluorescence (XRF) detection limits of 0.003 and 0.010 wt. %, respectively, in the high purity ingots. Atom-probe tomography (APT) was carried out and revealed Si partitioning at the following interfaces: grain boundaries, MC carbide/γ, M 3 B 2 boride/$γ$ and M 3 B 2 boride/$γ$'. Copper was found to primarily segregate to the $γ$' precipitates. An average of 2.4 × decrease in creep life and 4.3 × decrease in creep ductility was measured in the low purity alloys, which was attributed to the embrittlement caused by Si segregation to grain boundaries. Furthermore, the positive effect of B on the creep properties was mitigated by the presence of Si. Thermodynamic predictions for the matrix and γ' precipitate compositions represented the trends observed experimentally although the extent of preferential partitioning lacks accuracy. Monte Carlo simulations were performed to describe the partitioning of Cu and Si atoms to either $γ$ or $γ$' phases.

36 MATERIALS SCIENCE↗

An Alternative Casting Technique to Improve the Creep Resistance of Cast INCONEL Alloy 740H

The increasing performance requirements of power plant designs, such as advanced-ultra supercritical (A-USC), require the use of Ni-based superalloys to replace high-strength, ferritic-martensitic steels for components subjected to temperatures above 898 K (625 °C) and for austenitic stainless steels components at temperatures above 973 K (700 °C). To date, commercial Ni-based superalloy INCONEL 740H has been shown to be appropriate for use in A-USC power plants as boiler components in a wrought product. However, large complex components in boilers as well as other casings in the turbine and valve chest require castings of a thick-wall nature. Using the alloy in its cast form would be significantly valuable in terms of range of component size, geometry and complexity. Previous investigations revealed short creep lives from cast INCONEL alloy 740H. Here in this investigation, an alternative casting route that utilized a melt procedure resulting in a fine-grain casting, and in conjunction with a computationally optimized homogenization heat treatment, not only controlled the grain size and grain boundary structure but minimized chemistry variability and segregation. A primarily equiaxed and homogenous grain size distribution was obtained from this approach with better repartition of M 23 C 6 carbides along the grain boundaries. Furthermore, better than 38 pct increase was obtained for this material in comparison to the creep life obtained from the best performing conventionally cast material. More importantly, the fine-grain homogenized (FGH) casting route resulted in the Larson–Miller plot for this material that coincided with that of wrought alloy 740. At low creep stresses (with a test still in progress), the FGH casting is resulting in higher values of the LMP than the wrought alloy.

36 MATERIALS SCIENCE↗

Advancing Development and Application of Superalloys

This JOM topic is sponsored by the High Temperature Alloys Committee of TMS and addresses advances in the development and application of superalloys. Each year, the High Temperature Alloys Committee organizes symposia at the TMS and Materials Science and Technology annual meetings. In 2020, two symposia were organized for the TMS annual meeting on February 23–27 in San Diego, CA: Materials Design Approaches & Experiences V, co-sponsored by the Integrated Computational Materials Engineering Committee and Advancing Current and State-of-the-Art Applications of Ni- and Co-base Superalloys, co-sponsored by the Corrosion and Environmental Effects Committee. Later this year, the 14th International Symposium on Superalloys will be held on September 13-17 in Seven Springs, PA. The conference, held every 4 years, convenes members of the superalloy community to discuss recent challenges and discoveries affecting future performance and use of superalloys. The TMS High Temperature Alloys Committee meets at both the TMS Annual Meeting & Exhibition and the annual Materials Science and Technology conference. The meetings are open to anyone interested in high-temperature alloys. This special topic on Advancing Development and Application of Superalloys includes a range of sub-topics including mechanical performance, corrosion resistance, processing and advanced manufacturing techniques, which were submitted by research groups from industry, national laboratories and universities.

36 MATERIALS SCIENCE↗

Hot deformation behavior and flow stress modeling of a Ni-based superalloy

The deformation behavior of a novel Ni-based superalloy was investigated using isothermal compression on a Gleeble system at temperatures between 1050 and 1210 °C with strain rates between 0.001 and 0.1 s –1 . Flow-stress curves and electron backscatter diffraction maps were employed to experimentally identify the various flow mechanisms operative during deformation. Deformation at temperatures below 1130 °C presented strong work hardening with limited restoration during dynamic softening leading to partially recrystallized microstructures. Increasing the deformation temperature to and above 1130°C enhanced the driving force for dislocation and grain boundary mobility thereby enabling dynamic recovery (DRV) and dynamic recrystallization (DRX) mechanisms to better operate. Here, the influence of the strain rate was more evident during deformation at these temperatures. Increasing the strain rate from 0.001 s –1 to 0.1 s –1 resulted in a transition in dominant softening mechanism from DRV to DRX. Flow stress modeling using the Zener-Hollomon parameter was performed to obtain the activation energy and the constitutive equation for hot deformation of the alloy. Strong changes in flow behavior affected the accuracy of the flow stress model, and thus, the model was used alternatively to identify deformation parameters associated with various flow regimes. In doing so, the activation energy and the other equation constants were obtained for each deformation mechanism observed experimentally.

36 MATERIALS SCIENCE↗

Evolution of Tantalum Content During Vacuum Induction Melting and Electroslag Remelting of a Novel Martensitic Steel

The need for materials with superior thermal and mechanical properties while mitigating cost increases interest in new complex alloy compositions which brings challenges to manufacturing processes. In this investigation, vacuum induction melting (VIM) and electroslag remelting (ESR) of a novel tantalum (Ta)-containing martensitic steel was performed using standard industry practices at a laboratory scale. A 25 pct loss of Ta was measured from the VIM electrode to the ESR ingot using X-ray fluorescence. Several tools were used for broad characterization of the ingots, including LECO for chemistry analysis, scanning electron microscopy, and electron probe microanalysis for observation of the precipitate and inclusion phases post-VIM and post-ESR as well as computational modeling of the ESR process for the calculation of macrosegregation and inclusion travel. It was found that a significant amount of Ta{sub 2}O{sub 5} inclusions formed during VIM and were transferred to the slag during ESR. While ESR was particularly successful at decreasing the number density of inclusions by 95 pct, additional efforts are needed with regard to vacuum leak rate and purity of stock material when melting novel advanced steels.

36 MATERIALS SCIENCE↗

Design and thermomechanical properties of a γ' precipitate-strengthened Ni-based superalloy with high entropy γ matrix

A novel Ni-based superalloy was designed with γ' precipitate strengthening, controlled γ/γ' lattice misfit and high configurational entropy of the γ matrix for improved high temperature performance up to 800 degrees C. The alloy contains nano-sized γ' precipitates, MC and other grain boundary carbides. Three variants of the alloy were fabricated using vacuum induction melting, a computational-based homogenization cycle for reducing solidification segregation, and thermomechanical processing steps of forging followed by hot rolling to produce plates from which ASTM standard test specimens were extracted. Tensile testing at room temperature and elevated temperatures up to 800 degrees C revealed superior yield stress when compared to Nimonic 105 with good tensile strength values. Furthermore, the three alloys are machinable with maximum stresses comparable to standard practices as determined using deformation mechanisms maps obtained from Gleeble testing and EBSD analysis. Due to the composition of the experimental alloys falling outside the typical range used to populate thermodynamic databases, differences in phase predictions and related temperatures were observed between the experiment and Thermo-Calc predictions. Here, the γ' forming elements Ti and Nb had a similar effect on the γ' precipitates and indirectly contributed to changing the entropy of the γ matrix. Based on the results of this study, these alloys have the potential for use at 800 degrees C in energy structural applications. Definitions related to this novel class of alloys are discussed.

36 MATERIALS SCIENCE↗