Engineering topics

Deutsch, Todd

Publications and source records attributed to Deutsch, Todd.

5 records

DOE OSTI2024

Perovskite/Perovskite Tandem Photoelectrodes for Low-Cost Unassisted Photoelectrochemical Water Splitting

In this project, we aim to address the challenges of achieving efficient and cost-effective unassisted photoelectrochemical water splitting using perovskite/perovskite tandem photoelectrodes. We utilized the following unique approaches to advance our innovation. (1) We developed stable and efficient low-E g (1.2 – 1.4 eV) perovskites as the bottom electrodes. We demonstrated approaches to improve the photovoltaic performance and photothermal stability of low-E g Sn-Pb iodide perovskite solar cells. (2) We developed a low-temperature synthesis route to fabricate wide-E g (>1.8 eV) perovskite top electrodes. By combining theoretical and experimental investigation, we found methods to reduce the formation of defects and dislocations in the wide-E g mixed halide perovskites and suppress halide segregation. (3) We developed a robust metal oxide-based interconnecting layer to integrate two perovskite layers into tandem photoelectrodes. Our monolithically integrated tandem devices feature a high V OC of more than 2 V and a high J SC of more than 15 mA/cm 2 . We showed the new design of the tandem photoelectrodes that is critical to the stable operation of tandem photoelectrodes for unassisted PV/PEC water splitting. (4) We demonstrated a water-impermeable barrier of carbon paste/epoxy/metal foil composite, which can prevent photocorrosion and water ingress of perovskite active layers. This surface protection enabled the operation of perovskite photoelectrodes in water and significantly enhanced the long-term stability of our tandem devices. (5) We conducted standardized PEC characterization in collaboration with NREL and reported accurate determination of solar-to-hydrogen conversion efficiencies of perovskite/perovskite tandem photoelectrodes. At the end of the project, we demonstrated perovskite/perovskite tandem photoelectrodes with STH efficiencies of up to 18% and less than 20% efficiency loss after continuous operation for more than 500 hours in water. Our results demonstrate the potential to develop a low-cost, durable, and efficient water-splitting system that meets the DOE 2026 and 2031 cost targets for hydrogen production.

08 HYDROGEN↗

DOE OSTI2024

NX Fuels H2 Shot Incubator Phase I (CRADA Final Report)

NX Fuels will work with NREL to perform Life-Cycle Analysis (LCA) and Techno-Economic Analysis (TEA) for NX Fuels' solar H 2 system. TEA/LCA modeling developed early on will provide insight on the most critical parameters related to the green H 2 cost and environmental impacts and help us create the business case at scale. This project will advance the Nation’s decarbonization goals by demonstrating the economic feasibility of NX Fuels clean hydrogen production pathway and evaluate its impact on CO 2 emissions.

08 HYDROGEN↗

DOE OSTI2023

HydroGEN Seedling: Monolithically Integrated Thin Film/Silicon Tandem Photoelectrodes for High-Efficiency and Stable Photoelectrochemical Water Splitting

In this project, we propose to develop monolithically integrated Si-based tandem photoelectrodes to achieve both high solar-to-hydrogen (STH) efficiency (>15%) and long-term stability (>1,000 hours) in spontaneous water splitting systems. The proposed tandem devices consist of a Ta 3 N 5 , BCTSSe, or In 0.5 Ga 0.5 N top junction, which has a bandgap of ~1.7-2.0 eV and can split the solar spectrum with the Si bottom junction. Ta 3 N 5 , BCTSSe, and InGaN will be grown/deposited on a low-resistivity nanowire tunnel junction on Si substrates using atomic layer deposition (ALD), sputtering, and molecular beam epitaxy (MBE), respectively. Both n and p-type Si solar wafers will be utilized, which can serve as the photoanode or photocathode, respectively. We will use N-rich GaN ultrathin passivation layers to protect photoelectrodes from corrosion and oxidation.

08 HYDROGEN↗

DOE OSTI2022

DOE EERE AMO Electrochemistry for Manufacturing (Workshop Report)

The Advanced Manufacturing Office (AMO) aims to improve the efficiency, productivity, environmental impact, and competitiveness of the manufacturing sector. The use of electrochemistry in manufacturing could help AMO achieve these goals with its potential to have significant impact on sustainability, energy and carbon efficiency, and U.S. manufacturing competitiveness. The “Electrochemistry for Manufacturing” workshop series was designed to help AMO understand (1) how electrochemistry can be used within the manufacturing sector to achieve AMO’s goals and (2) the support for technology and workforce development that is needed from AMO to leverage crosscutting efforts that can enable successful outcomes.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

DOE OSTI2020

Modeling Water Electrolysis in Bipolar Membranes

Bipolar membranes (BPMs) have proven useful in numerous electrochemical energy conversion and storage applications, including fuel cells and electrolyzers. However, water dissociation in bipolar membrane electrolysis cells (BPMECs) is a complicated phenomenon that occurs via several different pathways. In this work, we develop a model based on the Poisson-Nernst-Planck system that includes a multistep water-dissociation mechanism to observe the fundamental processes that contribute to BPMEC performance. The model, which is validated to in-house experimental data, demonstrates that the junction potential is the most significant contributor to the total electrolysis voltage. We investigated the effects of water-dissociation catalysts and found that the optimal catalyst $p{K}_{a}$ depends on how the catalyst is integrated into the BPM (although values near 7 are typically best, in accordance with conventional wisdom). We also simulated the water content across the BPM and found that dry-out is not a significant issue when the membrane is in contact with liquid water on both sides. The species conservation approach taken here leads to a physical understanding of the system without using any fitting parameters.

25 ENERGY STORAGE↗