Search NASA⌕ Search

Engineering topics

Devin E Burns

Publications and source records attributed to Devin E Burns.

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2023

Reduced-Order Modeling and Parameter Identification of Wind Tunnel Measurement Systems

We present a method to develop a physics-based, reduced-order model of a wind tunnel measurement system (including a sting, strain gage force balance, and test article) that can be used to predict the dynamics of the system. This reduced-order model is combined with a simple finite element beam model of a sting to estimate the dynamics of the full assembly. We make comparisons between a full finite element model and the hybrid reduced-order model to show that this hybrid reduced-order model is capable of predicting the first six natural frequencies to within 10% error. This technique could be used to identify reduced-order parameters for a large number of balances and stings, which could then be used to estimate the dynamics of different measurement assemblies.

Reduced-order Modeling↗
NASA NTRS2020

Wind Tunnel Balance Design: A NASA Langley Perspective

This document chronicles and captures force balance design principles accumulated over the last 50 years at NASA Langley Research Center (LaRC). Many design and guidance internal memorandums have been drafted over the years, some as informal as a design engineer€™s notes for a particular balance design. To date, there has been no comprehensive balance design or best practices documentation available on LaRC's extensive design expertise. Therefore, the primary goal of this knowledge capture document is to assemble and organize the presentation of this historical corpus of knowledge for future balance engineers.

Devin E Burns↗
NASA NTRSDate not supplied

Additively Manufactured Wind Tunnel Balances for Propulsive Force Measurement

Propulsive forces and moments during powered descent are not understood well enough to design an entry, decent, and landing vehicle with high confidence using solely computational fluid dynamics modelling (CFD). Therefore, wind tunnel testing is required to quantify uncertainties in computational modeling and simulation. Wind tunnel balances are structural, high-precision, multi-axis force transducers that provide direct measurement of these aerodynamic forces and moments, however their complex designs make them costly and time consuming to produce and approaches used to manufacture them have not changed significantly since the 1960s. This work demonstrates that additive manufacturing (AM) can be used to manufacture wind tunnel balances with significantly reduced fabrication time and expense. Moreover, the design flexibility afforded by the additive manufacturing process has the potential to enable new capabilities with respect to measuring propulsion forces during entry, decent, and landing testing. Here we present two novel balance designs enabled by AM. One will provide direct measurement of aerodynamic interference forces and moments on powered descent models (retropropulsion forces) to support CFD validation and further development of Mars human landing vehicle concepts. The second design will be used to characterize a reaction control system during entry descent and landing testing over a wide Mach number range.

Wind tunnel balance↗
NASA NTRSDate not supplied

Additively Manufactured Balances for Propulsive Force Measurement

Propulsive forces and moments during powered descent are not understood well enough to design an entry, decent, and landing vehicle with high confidence using solely computational fluid dynamics modelling (CFD). Therefore, wind tunnel testing is required to quantify uncertainties in computational modeling and simulation. Wind tunnel balances are structural, high-precision, multi-axis force transducers that provide direct measurement of these aerodynamic forces and moments, however their complex designs make them costly and time consuming to produce and approaches used to manufacture them have not changed significantly since the 1960s. This work demonstrates that additive manufacturing (AM) can be used to manufacture wind tunnel balances with significantly reduced fabrication time and expense. Moreover, the design flexibility afforded by the additive manufacturing process has the potential to enable new capabilities with respect to measuring propulsion forces during entry, decent, and landing testing. Here we present two novel balance designs enabled by AM. One will provide direct measurement of aerodynamic interference forces and moments on powered descent models (retropropulsion forces) to support CFD validation and further development of Mars human landing vehicle concepts. The second design will be used to characterize a reaction control system during entry decent and landing testing over a wide Mach number range.

Wind tunnel balance↗
NASA NTRSDate not supplied

Design of a Wind Tunnel Balance using Topology Optimization Considering Multifunctional Stress Performance

This paper proposes a new topology optimization formulation for multi-functional performance of a compliant sensor structure–a wind tunnel balance. Compliant mechanism design is one of the main applications of topology optimization and plenty of successful design studies have been reported. However, design practicability is still questionable when stress concentration is critical due to complex/combined loads, especially at compliant hinge joints. In this paper, we formulate a new topology optimization formulation considering multiple loading scenarios in a compliant sensor structure design. Two separate constraints,one related to sensor performance and the other focused on structural safety in terms of maximum von Mises stress, are included in the design formulation. This formulation is to achieve excellent sensitivity of an applied axial load while maintaining structure safety with a combined general load applied which is one order higher than the axial load. This challenging problem is solved using a well-known SIMP approach with the relaxation and projection methods.

Myung Kyun Sung↗
NASA NTRSDate not supplied

A New Flow-Through Wind Tunnel Balance for Retropropulsion Testing

Supersonic retropropulsion is believed to be an enabling technology for large-scale human Mars lander vehicle concepts. Ground testing of such vehicles requires the development of new flow-through wind tunnel balances because no suitable balances exist. A new flow-through balance is designed that employs membranes in place of bellows, which have historically been used, and that passes the flow through load bearing parts of the balance. Flow through the balance is optimized via the addition of flow guides, which are manufactured as separate parts, and attached to the balance. Calibration of this new flow-through balance demonstrates that it can suitably characterize the load and pressure ranges it was designed for, which provides aero researchers a new tool to directly measure supersonic retropropulsion performance of powered descent vehicles.

Flow through balance↗
NASA NTRSDate not supplied

A New Flow-Through Balance for Retropropulsion Testing

Supersonic retropropulsion is believed to be an enabling technology for large-scale human Mars lander vehicle concepts. Ground testing of such vehicles requires the development of new flow-through wind tunnel balances because no suitable balances exist. A new flow-through balance is designed that employs membranes in place of bellows, which have historically been used, and that passes the flow through load bearing parts of the balance. Flow through the balance is optimized via the addition of flow guides, which are manufactured as separate parts, and attached to the balance. Calibration of this new flow-through balance demonstrates that it can suitably characterize the load and pressure ranges it was designed for, which provides aero researchers a new tool to directly measure supersonic retropropulsion performance of powered descent vehicles.

Flow through balance↗
NASA NTRSDate not supplied

Advancements in Force and Angle Measurement by the NFMTC

The National Force Measurement Technology Capability (NFMTC) is a nationwide partnership established in 2008 and sponsored by NASA’s Aeronautics Evaluation and Test Capabilities (AETC) project to maintain and further develop force and angle measurement capabilities primarily for NASA’s ground test facilities. One of the NFMTC’s primary objectives is to develop new force and angle measurement capabilities to meet the needs of researchers testing in NASA’s ground test facilities. This work will highlight several new capabilities that are either at or near operational readiness. A new six-component flow-through balance was designed and fabricated to support an upcoming retropropulsion test campaign at the NASA Langley Unitary Plan Wind Tunnel. The balance employs membranes in place of bellows, which have historically been used, and passes the flow through load bearing parts of the balance. Flow through the balance is optimized via the addition of flow guides, which are manufactured as separate parts, and attached to the balance. Calibration of this new flow-through balance demonstrates that it can suitably characterize the load and pressure ranges it was designed for, which provides aero researchers a new tool to directly measure retropropulsion performance of powered descent vehicles. Balances used in NASA’s ground test facilities are typically either single-piece balances or floating-frame balances. Historically, these two types of balances have generally used different front-end (model) attachments. Single-piece balances generally have a cylindrical front end that is forward of any measuring sections and at a reduced diameter relative to the balance outer diameter. Floating-frame balances generally have front end fits that extend over one or more measuring sections and that engage at the balance outer diameter. Recently, the NFMTC fabricated a single-piece balance with a front end fit that is compatible with the hardware used to calibrate floating-frame balances. Calibration results evaluating this front end fit will be presented. From a recent survey of angle measurement needs, the development of smaller angle measurement packages was identified as one area of improvement. Micro-electromechanical systems (MEMS) are continually being refined to provide high performance accelerometers that are a fraction of the volume of the quartz flexure based accelerometers that are standard in wind tunnels. A survey of commercial off-the-shelf MEMS accelerometers was conducted, and it identified the Safran Colibrys MS lines to be of adequate performance. Single-axis test boards and tri-axis rigid-flex production boards were designed and fabricated with a volume of approximately .18 cubic inches. The boards were designed to provide all the necessary conditioning for the MEMS accelerometers at levels to meet or exceed all requirements for the MS line sensors. Preliminary testing of these assembled sensor packages has demonstrated acceptable performance for wind-tunnel angle measurement. Several new rotating balances are at various stages of completion for NASA Glenn Research Center’s fan drive rigs. These balances provide direct measurement of thrust and torque of a driven fan or fan section to provide an estimate of fan efficiency and net thrust. Three two-component balances have been recently completed, and one six-component balance is in active development. A custom rotating telemetry system has been developed to support testing with these balances, and the telemetry system is integrated into the forward end of each one. The telemetry system is designed to remove mechanical sliprings by using an optical ethernet-based slipring for data transmission.

Force measurement↗
NASA NTRSDate not supplied

Testing of Two Mars Powered Descent Vehicle Concepts in the Langley Unitary Plan Wind Tunnel

Testing was conducted in the NASA Langley Unitary Plan Wind Tunnel in order to investigate the aerodynamic interference of sub-scale versions of two Mars powered descent vehicle concepts at supersonic Mach numbers (2.4 and 3.5): a model based on a blunt hypersonic inflatable aerodynamic decelerator (HIAD) and the second representing a more slender rigid vehicle with body flaps (CobraMRV). Each model was designed to accommodate up to eight nozzles, with the HIAD model having five different nozzle configurations to investigate the effects of nozzle location, cant angle, and area ratio. The models were tested with high pressure air as the nozzle plume gas, and included the following instrumentation: high-speed video, discrete steady state and high-frequency pressure, pressure sensitive paint, and a new flow-through force and moment balance for the HIAD model. The high-speed imagery showed the overall expected growth of the shock layer to increasing thrust levels. The discrete stagnation pressure data on the HIAD model with four and eight blowing nozzles was sensitive to thrust coefficient with the nozzles canted at 0 degrees, whereas having nozzles canted outward 20 degrees and/or being located closer to the heatshield shoulder largely removed that sensitivity. The CobraMRV model stagnation pressure was more sensitive to tunnel Mach number and sideslip angle, due to the nozzle arrangement and plume interference. Pressure sensitive paint data quality was compromised by paint damage from frequent model changes, especially for the HIAD model. However, pressure coefficient data on the CobraMRV model showed the same trends as the discrete pressure measurements, as well as a sensitivity to non-zero sideslip angles. The aerodynamic force coefficients were derived from the pressure sensitive paint data. On the HIAD models, the primary force coefficient decreased with increasing thrust due to the nozzle plumes blocking flow to the heatshield area surrounding the nozzle exist. On the CobraMRV model, the force coefficient was relatively insensitive to thrust coefficient at the lower Mach number when sideslip angle was 0 degrees The force coefficient decreases with increasing thrust coefficient when the sideslip angle is 10 degrees. Balance data quality was negatively impacted by thermal drift issues that were not apparent in pre-test calibration measurements, thus preventing usable test data. Results and lessons learned will be used to take further technology development steps, including more advanced ground test techniques and flight testing.

Karl T Edquist↗