Search NASA⌕ Search

Engineering topics

Deyst, J. J.

Publications and source records attributed to Deyst, J. J..

12 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

F-8 DFBW sensor failure identification using analytic redundancy

The structure of a sensor failure detection and identification system designed for the NASA F-8 DFBW aircraft is outlined. The system is for use in a dual-redundant environment, and it takes maximal advantage of all functional relationships among the sensed variables. The identification logic uses the quality sequential probability ratio, which provides a useful on-line measure of confidence in the various forms of analytic redundancy. Preliminary simulation results indicate good behavior of the analytic decision statistic, based on the sequential probability ratio test.

Deckert, J. C.↗
NASA NTRS1977

Evaluation of the F-8 DFBW analytic redundancy sensor FDI algorithm using telemetry data

In this paper we present a reliable technique for failure detection and identification (FDI) for dual redundant flight control sensors aboard the NASA F-8 digital fly-by-wire (DFBW) aircraft, and we discuss the successful application of the technique to identifying failures injected on test flight telemetry data. The technique exploits the analytic redundancy which exists as relationships among variables being measured by dissimilar instruments. With straightforward modification the technique may be extended to provide failure monitoring of a single remaining sensor after the identified failure of its companion sensor.

Deckert, J. C.↗
NASA NTRS1976

Dual redundant sensor FDI techniques applied to the NASA F8C DFBW aircraft

An onboard failure detection and identification (FDI) technique for dual redundant sensors on the NASA F8C digital fly-by-wire (DFBW) aircraft is presented. The failure of one of a pair of sensors of the same type is detected by a direct redundancy trigger which observes the difference between the outputs of these two sensors. Identification of the failed sensor is accomplished utilizing the analytic redundancy that exists as kinematic and functional relationships among the variables being measured by dissimilar instruments. In addition, identification of generic failures, common to both instruments of a given type, is accomplished by using a time trigger to periodically initiate analytic redundancy failure identification tests for individual sensors. The basic form of these tests is the comparison of the measurement of a variable using the suspect instrument with another measurement of the same variable obtained using other instrument types.

Desai, M. N.↗
NASA NTRS1975

Two self-test methods applied to an inertial system problem

The paper describes two self-test procedures applied to the problem of estimating the biases in accelerometers and gyroscopes on an inertial platform. The first technique is the weighted sum-squared residual (WSSR) test, with which accelerator bias jumps are easily isolated, but gyro bias jumps are difficult to isolate. The WSSR method does not take full advantage of the knowledge of system dynamics. The other technique is a multiple hypothesis method developed by Buxbaum and Haddad (1969). It has the advantage of directly providing jump isolation information, but suffers from computational problems. It might be possible to use the WSSR to detect state jumps and then switch to the BH system for jump isolation and estimate compensation.

Willsky, A. S.↗
NASA NTRS1975

Maximum likelihood failure detection techniques applied to the shuttle orbiter reaction control subsystem

A technique for on-board detection and identification of hard failures and leaks of the shuttle orbiter reaction control subsystem jets, during the orbital flight phase, is presented. The method uses gimbal angle and linear accelerometer measurements from the orbiter inertial measurement unit and requires no additional hardware. Extended Kalman filters with residual traps are employed for state estimation, and generalized likelihood ratio tests for jet failure identification. Rigid body simulation results indicate identification times of less than 2 seconds for hard jet failures and less than 70 seconds for jet leaks.

Deckert, J. C.↗
NASA NTRS1974

A passive wingtip load alleviation system

A passive wingtip load alleviation system was devised, tested, and analyzed for its effect on the reduction of structural deformations and the extension of flutter speed. The sensors responded to changes in angle of attack and vertical movement of the wingtip and were used to deflect a trailing edge flap to alleviate the induced loads.

Harlan, R. B.↗