Search NASA⌕ Search

Engineering topics

Di Stefano, Carlos

Publications and source records attributed to Di Stefano, Carlos.

At least 19 records

Evaluation of the relative importance of preheat from hohlraum x rays and a radiative shock on a low-density foam

Indirectly driven shock-tube experiments were performed on the Omega Laser Facility to evaluate the relative importance of hohlraum x ray and radiative shock preheat sources on a low-density foam. X rays emitted from the hohlraum and a subsequent shock wave are channeled into a low-density foam sample, which contains a plastic preheat-witness disk placed downstream of the foam. Simultaneous radiographic measurements of the shock speed in the foam and the expansion rate of the witness disk due to preheat allow for the observation of effects from the hohlraum's low-energy and high-energy x-ray spectrum. Here we showed, from simulations, that low-energy x rays from the hohlraum are preferentially absorbed near the ablator surface (where the hohlraum and the shock tube meet), while higher-energy x rays largely pass through the ablator and foam and are volumetrically absorbed by the witness disk. Reproducing the experimentally measured shock speed and expansion of the witness disk simultaneously, we extracted the temperature evolution of preheated foam from the simulation and evaluated the relative importance of preheat sources on a low-density foam from hohlraum x-ray radiation and radiative shock. We found that radiation from the shock front was more effective at preheating the low-density foam than the high-energy x rays from the hohlraum. This shock-tube preheat experiment is important for understanding the results of the MARBLE experiments at the National Ignition Facility because initial conditions of foam-filled MARBLE capsules are sensitive to preheat.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

HED Hydrodynamics in the Common Modeling Framework

Within the Common Modeling Framework (CMF), the HED Hydrodynamics Project has implemented a common methodology, or "Authority", for modeling high energy density (HED) experiments by extending development of the Eulerian Applications Project code Authority, "EAPA," to include relevant physics models, customization tools and templates, and in situ and post-processing capabilities. Additionally, several models for small-scale HED experiments were successfully added to the CMF and simulations reproduce the results of preexisting, benchmarked input decks. We expect use of the CMF to improve our effectiveness in developing predictive capabilities for experiments ranging from small-scale planar single-interface, single-shock to multi-interface, multi-shock configurations and up through multi-shell inertial confinement fusion (ICF) implosions. Additionally, this will strengthen our ability to design future targeted experiments. Using the CMF infrastructure and Authorities for HED modeling has three key impacts. First, it enables a version-controlled, pedigreed and archived base model for each experiment with tools that allow easy setup, execution and analysis of simulations to assess and/or expose sensitivities to various parameters. Second, having a common base set of inputs and physics definitions helps identify systematic differences between models in the codes and experimental data to support code validation, and build confidence in our predictive capabilities. Finally, designed to work in concert with multiple programs and projects including PEM, IC, OES, V&V and DSW, the CMF supports improved collaboration and integration through shared model definitions, data, simulations and results, enhancing the workflow required to underwrite the knowledge base and capabilities ultimately required for stockpile stewardship

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Reducing Direct Drive Preheat with Dopants

Preheat in laser-driven experiments can have negative impacts on inertial confinement fusion (ICF) and hydrodynamic experiments. While many groups employ the use of dopants to reduce or block preheat, direct quantification has not previously been explored. We developed a planar platform and a series of ablator targets to measure the electron and x-ray spectra generated by laser-plasma interactions with a direct drive using OMEGA-60. By comparing both thin ablators (75 μm) and thick ablators (270 μm) that were either pure CH, 3% Si doped or 3% I doped, we were able to measure differences in electron and x-ray spectra. In addition, we observed the preheat growth of tracer layers and observed reductions in the growth with different materials. We find that iodine or a thin gold layer is the best at tamping the direct-drive preheat at OMEGA, but that the growth is still significant.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Mshock, a thin layer Richtmyer-Meshkov instability experiment

The Mshock campaign is studying the feed through of the Richtmyer-Meshkov instability (RMI) in a thin layer in the high energy density (HED) regime. Experiments utilize a beryllium shock tube filled with low density foam and a high density plastic to study the instability. Initial experiments were performed at the OMEGA laser facility and recently at the National Ignition facility. While the basic design of the experiment is the same, critical components were changed to optimize the data quantity and clarity for the more energetic NIF.

42 ENGINEERING↗

Machining Specific Fourier Power Spectrum Profiles into Plastics for High Energy Density Physics Experiments [Machining Specific Fourier Power Spectrum Profiles into Plastics for HEDP Experiments]

In this paper, the High Energy Density Physics program at Los Alamos National Laboratory (LANL) has had a multiyear campaign to verify the predictive capability of the interface evolution of shock propagation through different profiles machined into the face of a plastic package with an iodine-doped plastic center region. These experiments varied the machined surface from a simple sine wave to a double sine wave and finally to a multitude of different profiles with power spectrum ranges and shapes to verify LANL’s simulation capability. The MultiMode-A profiles had a band-pass flat region of the power spectrum, while the MultiMode-B profile had two band-pass flat regions. Another profile of interest was the 1-Peak profile, a band-pass concept with a spike to one side of the power spectrum. All these profiles were machined in flat and tilted orientations of 30 and 60 deg. Tailor-made machining profiles, supplied by experimental physicists, were compared to actual machined surfaces, and Fourier power spectra were compared to see the reproducibility of the machining process over the frequency ranges that physicists require.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

H_Hyd_Shktub_Mshock_III, JJJ, KKK (S01,S02,S03) on the National Ignition Facility

These experiments are the first experiments in the Mshock campaign at the National Ignition Facility. The experiment is scheduled to be conducted on Dec. 14, 2017. The goal of the Mshock campaign is to study feedthrough dynamics of the Richtmyer- Meshkov instability in a thin layer. These dynamics will be studied in both a reshock configuration (initially) and then in a multi-shock configuration where it is planned to reshock the RM instability up to 3 times (four shocks total).

42 ENGINEERING↗