Search NASA⌕ Search

Engineering topics

Diallo, A.

Publications and source records attributed to Diallo, A..

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Simultaneous enhancement of tritium burn efficiency and fusion power with low-tritium spin-polarized fuel

This study demonstrates that using spin-polarized deuterium-tritium (D-T) fuel with more deuterium than tritium can increase tritium burn efficiency (TBE) by at least an order of magnitude without compromising fusion power output, compared to unpolarized fuel. Although previous studies show that a low tritium fraction can enhance TBE, this strategy resulted in reduced fusion power density. The surprising improvement in TBE at fixed power reported here is due to the TBE increasing nonlinearly with decreasing tritium fraction but the fusion power density increasing roughly linearly with D-T cross section. A study is performed for an ARC-like tokamak producing 481 MW of fusion power with unpolarized 53:47 D-T fuel, finding the minimum startup tritium inventory (I startup,min ) is 0.69 kg. By spin-polarizing half of the fuel and using a 60:40 D-T mix, I startup,min is reduced to 0.08 kg, and fully spin-polarizing the fuel with a 63:37 D-T mix further reduces I startup,min to 0.03 kg. Some ARC-like scenarios are predicted to achieve plasma ignition with relatively modest spin polarization. These findings indicate that, with advancements in helium divertor pumping efficiency, TBE values of approximately 10%–40% could be achieved using low-tritium-fraction and spin-polarized fuel with minimal power loss. This would dramatically lower tritium startup inventory requirements and reduce the amount of on-site tritium. More generally than just for spin-polarized fuels, increased plasma performance can be used to increase TBE. This strongly motivates the development of spin-polarized fuels and low-tritium-fraction operation for burning plasmas.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

Applicability of alkali beam emission spectroscopy on NSTX-U

Understanding fast pedestal dynamics and turbulent transport in the edge and scrape-off layer (SOL) plasma of spherical tokamaks is crucial for the design and operation of future fusion reactors. The alkali beam emission spectroscopy diagnostic technique offers a means to measure the absolute electron density radial profile and fluctuation amplitude in these regions. Here, in this study, we demonstrate that injecting a sodium neutral beam radially into the plasma and analyzing the light emission from its 3p–3s atomic transition using near-orthogonal viewing angles allows for accurate measurement of the electron density profile and fluctuations in the National Spherical Torus Experiment (NSTX) Upgrade spherical tokamak. Our findings indicate a peak signal-to-noise ratio of 118 in the pedestal and 12 in the SOL under typical NSTX plasma conditions. The spatial resolution for the electron density profile is estimated to be between 2 and 8 mm, while for fluctuation measurements, it ranges from 12 to 15 mm.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

WEST full tungsten operation with an ITER grade divertor

The mission of WEST (tungsten-W Environment in Steady-state Tokamak) is to explore long pulse operation in a full tungsten (W) environment for preparing next-step fusion devices (ITER and DEMO) with a focus on testing the ITER actively cooled W divertor in tokamak conditions. Following the successful completion of phase 1 (2016-2021), phase 2 started in December 2022 with the lower divertor made entirely of actively cooled ITER-grade tungsten mono-blocks. A boronization prior the first plasma attempt allowed for a smooth startup with the new divertor. Despite the reduced operating window due to tungsten, rapid progress has been made in long pulse operation, resulting in discharges with a pulse length of 100 s and an injected energy of around 300 MJ per discharge. Plasma startup studies were carried out with equatorial boron nitride limiters to compare them with tungsten limiters, while Ion Cyclotron Resonance Heating assisted startup was attempted. High fluence operation in attached regime, which was the main thrust of the first campaigns, already showed the progressive build up of deposits and appearance of dust, impacting the plasma operation as the plasma fluence increased. In total, the cumulated injected energy during the first campaigns reached 43 GJ and the cumulated plasma time exceeded 5 h. Demonstration of controlled X-Point Radiator regime is also reported, opening a promising route for investigating plasma exhaust and plasma-wall interaction issues in more detached regime. This paper summarises the lessons learned from the manufacturing and the first operation of the ITER-grade divertor, describing the progress achieved in optimising operation in a full W environment with a focus on long pulse operation and plasma wall interaction.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Design of a Thomson scattering diagnostic for the SMall Aspect Ratio Tokamak (SMART)

Here, we describe the design of a Thomson scattering (TS) diagnostic to be used on the SMall Aspect Ratio Tokamak (SMART). SMART is a spherical tokamak being commissioned in Spain that aims to explore positive triangularity and negative triangularity plasma scenarios at a low aspect ratio. The SMART TS diagnostic is designed to operate at high spatial resolution, 6 mm scattering length in the low-field side and 9 mm in the high-field side regions, and a wide dynamic range, electron temperature from 1 eV to 1 keV and density from 5 x 10 18 m -3 to 1 x 10 20 m -3 ⁠, to resolve large gradients formed at the plasma edge and in the scrape-off layer (SOL) under different triangularities and low aspect ratios. A 2 J @1064 nm laser will be used that is capable of operating in the burst mode at 1, 2, and 4 kHz to investigate fast phenomena and at 30 Hz to study 1 s (or more) long discharges. The scattered light will be collected over an angular range of 60° – 120° from 28 spatial points in the midplane covering the entire plasma width and the outer midplane SOL. Each scattering signal will be spectrally resolved on five wavelength channels of a polychromator to obtain the electron temperature measurement. We will also present a method to monitor in situ laser alignment in the core during calibrations and plasma operations.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Acceleration mechanisms of energetic ion debris in laser-driven tin plasma EUV sources

Laser-driven tin plasmas are driving new-generation nanolithography as sources of extreme ultraviolet (EUV) radiation centered at 13.5 nm. A major challenge facing industrial EUV source development is predicting energetic ion debris produced during the plasma expansion that may damage the sensitive EUV channeling multilayer optics. Gaining a detailed understanding of the plasma dynamics and ion acceleration mechanisms in these sources could provide critical insights for designing debris mitigation strategies in future high-power EUV sources. Here, we develop a fully kinetic model of tin-EUV sources using one-dimensional particle-in-cell simulations to study ion debris acceleration, which will be valuable for cross-validation of radiation-hydrodynamic simulations. An inverse-bremsstrahlung heating operator is used to model the interaction of a tin target with an Nd:YAG laser, and thermal conduction is included through a Monte Carlo Coulomb collision operator. While the large-scale evolution is in reasonable agreement with analogous hydrodynamic simulations, the significant timescale for collisional equilibration between electrons and ions allows for the development of prominent two-temperature features. A collimated flow of energetic ions is produced with a spectrum that is significantly enhanced at high energies compared to fluid simulations. The dominant acceleration mechanism is found to be a large-scale electric field supported mainly by the electron pressure gradient, which is enhanced in the kinetic simulations due to the increased electron temperature. We discuss the implications of these results for future modeling of tin-EUV sources and the development of debris mitigation schemes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Stability analysis of WEST L-mode discharges with improved confinement from boron powder injection

WEST L-mode plasmas with dominant electron heating and no core torque source have observed improvements in confinement during boron (B) powder injection. These results are reminiscent of previous powder injection experiments on other devices and gaseous impurity seeding experiments on WEST. During powder injection, the stored energy increased up to 25% due to enhanced ion and electron heat and particle confinement. The improvements in confinement were not indicative of an L-H transition. To identify the dominant mechanisms and the causality chain behind these improvements in confinement, we employ interpretative modeling using METIS, predictive integrated modeling using a high-fidelity plasma simulator (HFPS), and stand-alone gyrokinetic simulations using quasi-linear gyrokinetic code. Interpretative modeling with METIS allowed for the estimation of missing data while maintaining good overall consistency with experiment. These results provided the initial conditions for fully predictive flux driven simulations using the HFPS. From these simulations, quasi-linear gyrokinetic analysis was performed at ρ = 0.5 and ρ = 0.65. Collisionality was found to be a strong candidate for the turbulence suppression mechanism at ρ = 0.5, while a combination of collisionality and the T e /T i ratio was found to be the likely mechanism at ρ = 0.65. The results additionally suggested that increased Z eff (through main ion dilution) could play a role in the improved confinement, but this could not be confirmed due to a lack of experimental measurements. The modeling framework established here can now be used to evaluate and exploit a variety of future powder injection experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2023

Toward streaked collective Thomson scattering measurements on an extreme ultraviolet plasma light source

Here we show through forward modeling calculations that streaked collective Thomson scattering measurements are feasible on laser-produced tin plasmas generated under conditions relevant for extreme ultraviolet lithography. Using a 532 nm probe laser beam, the feasibility of simultaneous measurements of electron plasma wave (EPW) and ion acoustic wave (IAW) spectra is investigated. Absolute photon counts for laser scattering off both waves are calculated. Probe laser electron heating and bremsstrahlung background radiation effects are accounted for. While a large spatiotemporal region can be successfully probed based on the IAW feature, only one measurement location can be accessed through the EPW as a result of the low signal to noise ratio. A portable/traveling tabletop system is proposed.

47 OTHER INSTRUMENTATION↗
DOE OSTI2023

Novel angular velocity estimation technique for plasma filaments

Magnetic field aligned filaments such as blobs and edge localized mode filaments carry significant amounts of heat and particles to the plasma facing components and they decrease their lifetime. The dynamics of these filaments determine at least a part of the heat and particle loads. These dynamics can be characterized by their translation and rotation. In this paper, we present an analysis method novel for fusion plasmas, which can estimate the angular velocity of the filaments on frame-by-frame time resolution. After pre-processing, the frames are two-dimensional (2D) Fourier-transformed, then the resulting 2D Fourier magnitude spectra are transformed to log-polar coordinates, and finally the 2D cross-correlation coefficient function (CCCF) is calculated between the consecutive frames. The displacement of the CCCF’s peak along the angular coordinate estimates the angle of rotation of the most intense structure in the frame. Further, the proposed angular velocity estimation method is tested and validated for its accuracy and robustness by applying it to rotating Gaussian-structures. The method is also applied to gas-puff imaging measurements of filaments in National Spherical Torus Experiment plasmas.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗