Search NASA⌕ Search

Engineering topics

Dicarlo, D. J.

Publications and source records attributed to Dicarlo, D. J..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

Investigations of modifications to improve the spin resistance of a high-wing, single-engine, light airplane

A general aviation aircraft with drooped leading edge modifications for improvement of lateral stability at high angles of attack has been flight tested in combination with a ventral fin which improves directional stability. The two modifications were assessed in light of spin-resistance criteria proposed for incorporation into FAA certification regulations. The configuration combining outboard wing leading-edge droop and a ventral fin yielded a substantial increase in spin resistance, but fell short of all requirements encompassed by the proposed spin-resistance criteria.

Manuel, G. S.↗
NASA NTRS1986

Development of spin resistance criteria for light general aviation airplanes

A brief history of stall/spin technology for light general aviation airplanes is presented. Criteria needed to describe desirable characteristics of a spin-resistant airplane and means to evaluate airplanes for compliance with the criteria have been developed. Initial results from limited flight tests of an experimental high-wing airplane indicated that the basic configuration would not meet the spin resistance criteria. Further tests with the airplane modified to enhance its spin resistance are planned.

Dicarlo, D. J.↗
NASA NTRS1985

Leading-edge design for improved spin resistance of wings incorporating conventional and advanced airfoils

Discontinuous wing leading-edge droop designs have been evaluated as a means of modifying wing autorotative characteristics and thus improving airplane spin resistance. Addition of a discontinuous outboard wing leading-edge droop to three typical light airplanes having NACA 6-series wing sections produced significant improvements in stall characteristics and spin resistance. Wind tunnel tests of two wings having advanced natural laminar flow airfoil sections indicated that a discontinuous leading-edge droop can delay the onset of autorotation at high angles of attack without adversely affecting the development of laminar flow at cruise angles of attack.

Stough, H. P., III↗
NASA NTRS1985

Flight investigation of stall, spin and recovery characteristics of a low-wing, single-engine, T-tail light airplane

Flight tests were performed to investigate the stall, spin, and recovery characteristics of a four-place, low-wing, single-engine, T-tail, general aviation research airplane at an aft center-of-gravity position. Most stalls resulted in roll-offs. Spins were oscillatory in roll and pitch at 43 deg angle of attack; the magnitude of the oscillations was determined by aileron position. Power, flap deflection, and landing gear position did not affect the angle of attack to the spin. Antispin rudder followed by forward wheel with ailerons neutral produced the fastest and most consistent recoveries but the initial application of recovery controls did not always stop a spin.

Stough, H. P., III↗
NASA NTRS1984

Use of a discontinuous wing leading-edge modification to enhance spin resistance for general aviation airplanes

Spin resistance of two typical general aviation airplanes has been studied. Improvement in spin resistance due to an outboard wing leading-edge modification was evaluated through wind-tunnel and flight tests. The basic airplanes would readily enter a spin; however, with the wing modification the airplanes were highly spin resistant. Spin resistance has been related to the angle of attack of the outer wing panel and the yaw rate as a step toward development of guidelines for design of more spin resistant airplanes.

Dicarlo, D. J.↗
NASA NTRS1984

Wing design for spin resistance

Use of a discontinuous outboard wing leading edge to improve stall/spin characteristics has been evaluated through wind-tunnel and flight tests. Addition of such a discontinuous outboard wing leading-edge droop design to three light airplanes having NACA 6-series airfoil sections produced significant improvements in stall characteristics and spin resistance. The increased spin resistance of the modified airplanes has been related to the difference in angle of attack between the outer wing panel stall and the maximum attainable angle of attack.

Stough, H. P., III↗
NASA NTRS1983

Wing modification for increased spin resistance

A simple wing leading-edge modification has been developed that delays outer wing panel stall, thus maintaining roll damping to higher angles of attack and delaying the onset of autorotation. The stall angle of attack of the outer wing panel has been shown to be a function of the spanwise length of the leading-edge modification. The margin of spin resistance provided by the modification is being explored through flight tests. Preliminary results have been used to evaluate spin resistance in terms of the difference in angle of attack between outer wing panel stall and the maximum attainable angle of attack.

Stough, H. P.↗
NASA NTRS1981

Applications of dynamic stability parameters to problems in aircraft dynamics

The application and analysis of dynamic stability parameters were examined. The effects of wing leading edge modifications on the stalling and spinning characteristics of a single engine general aviation research airplane are evaluated. It is illustrated how dynamic stability parameters measured in wind tunnel tests are used to predict the spin resistance of this class of aircraft, and that autorotation criteria are derived from the relationships which exist between static and dynamic aerodynamic characteristics.

Chambers, J. R.↗
NASA NTRS1981

Applications of dynamic stability parameters to problems in aircraft dynamics

The paper presents highlights of a recent study which illustrates the application and analysis of dynamic stability parameters. More specifically, the investigation consisted of an evaluation of the effects of wing leading-edge modifications on the stalling and spinning characteristics of a single-engine general aviation research airplane. The results of the investigation illustrate how dynamic stability parameters measured in wind-tunnel tests are used to predict the spin resistance of this class of aircraft; and that autorotation criteria can be derived from the relationships which exist between static and dynamic aerodynamic characteristics.

Chambers, J. R.↗
NASA NTRS1980

Spinning for safety's sake

NASA Langley is currently engaged in a comprehensive research program to improve the stall/spin characteristics of general aviation airplanes. Part of this program has included systematic flight tests of a fully instrumented airplane to determine the effects of various tail, wing, and fuselage modifications, and variation of inertia, center-of-gravity, and control positions on the spin and recovery characteristics. Airplane equipment, onboard instrumentation ground equipment, test area, and test procedures have been combined to provide a safe, practical means for conducting research in preplanned hazardous conditions. Configuration changes produced spins varying from easily recoverable to unrecoverable, and wind section design significantly influenced airplane stall, spin, and recovery characteristics.

Stough, H. P., III↗
NASA NTRS1980

Effects of discontinuous drooped wing leading-edge modifications on the spinning characteristics of a low-wing general aviation airplane

Wind tunnel and flight tests were conducted to determine the effects of several discontinuous drooped wing leading-edge configurations on the spinning characteristics of a light, single-engine, low-wing research airplane. Particular emphasis was placed on the identification of modifications which would improve the spinning characteristics. The spanwise length of a discontinuous outboard droop was varied and several additional inboard segments were added to determine the influence of such leading-edge configurations on the spin behavior. Results of the study indicated that the use of only the discontinuous outboard droop, over a specific spanwise area, was most effective towards improving spin and spin recovery characteristics, whereas the segmented configurations having both inboard and outboard droop exhibited a tendency to enter a flat spin.

Dicarlo, D. J.↗
NASA NTRS1979

Exploratory study of the influence of wing leading-edge modifications on the spin characteristics of a low-wing single-engine general aviation airplane

A wide variety of model and airplane tests were conducted to explore the effects of wing leading-edge modifications on the stalling and spinning characteristics of a low-wing general aviation research airplane configuration. The results presented herein discuss the effects of leading-edge airfoil modifications applied to the full wing span and to partial-span locations. The results obtained in the study indicate that the wing modifications can produce large effects (both favorable or unfavorable) on spin resistance, developed spin characteristics, and spin recovery.

Dicarlo, D. J.↗
NASA NTRS1979

Spin flight research summary

An extensive general aviation stall/spin research program is underway at the NASA Langley Research Center. Flight tests have examined the effects of tail design, wing leading edge design, mass distribution, and minor airframe modifications on spin and recovery characteristics. Results and observations on test techniques are presented for the first airplane in the program. Configuration changes produced spins varying from easily recoverable slow, steep spins to unrecoverable, fast flat spins.

Patton, J. M., Jr.↗
NASA NTRS1976

A parametric analysis of visual approaches for helicopters

A flight investigation was conducted to determine the characteristic shapes of the altitude, ground speed, and deceleration profiles of visual approaches for helicopters. Two hundred thirty-six visual approaches were flown from nine sets of initial conditions with four types of helicopters. Mathematical relationships were developed that describe the characteristic visual deceleration profiles. These mathematical relationships were expanded to develop equations which define the corresponding nominal ground speed, pitch attitude, pitch rate, and pitch acceleration profiles. Results are applicable to improved helicopter handling qualities in terminal area operations.

Moen, G. C.↗
NASA NTRS1976

A study to determine the characteristic shapes of helicopter visual approach profiles

On previous helicopter instrument approach studies, pilot comments frequently indicated that the deceleration profiles were characterized by 'unnatural cues', and it was found that the pilots were comparing the motion and attitude cues with those obtained during visual approaches. Prior to this study, the characteristic shape of visual approach profiles had not been formally documented. Over 200 visual approaches were flown using different helicopter types, test subjects, and initial conditions, and the altitude and groundspeed profiles were measured by a precision tracking radar. The data from each approach were then processed, and the characteristic shape of the altitude, groundspeed, and deceleration profiles was determined for each set of initial conditions. These flight data were processed further using graphical analysis techniques and parameterization, which, in turn, led to developing closed-form equations that accurately describe the characteristic groundspeed and deceleration profiles. Results from this study can be used to select instrument approach profiles, to develop instrument approach control laws, and to define the corresponding hardware requirements.

Moen, G. C.↗
NASA NTRS1975

Operational experiences of a commercial helicopter flown in a large metropolitan area

A survey of commercial helicopter-operating experiences was conducted using a helicopter flight recorder in order to provide a basis for extending helicopter design and service-life criteria. These data are representative of 182 flight hours accumulated during 1414 flights comprised of the separate legs of the total route structure employed. The operating experiences are presented in terms of the time spent within different airspeed brackets, within the classifiable flight conditions of climb, en route, and descent, at various rates of climb and descent, and at different rotor rotational speeds. The results indicated that the helicopter spent a majority of the flight time at airspeeds either below 40 knots or above 100 knots. Rates of climb and descent were concentrated at values below 5.1 m/s (1000 ft/min) particularly for higher airspeeds. Normal acceleration experiences were low, both in the total number and peak value realized; however, an extremely large number of pitch angular-velocity experiences were noted. Rotor rotational speeds were normal with no occurrences above the upper red-line limit.

Dicarlo, D. J.↗
NASA NTRS1974

Simulation study of intracity helicopter operations under instrument conditions to category 1 minimums

A fixed-base simulator study was conducted to define pilot workload and task performance associated with instrument flight operations for an intracity helicopter passenger service. Displays considered necessary to provide a minimal capability under Instrument Flight Rules conditions were used to fly a representative commercial helicopter route structure in the New York area, with each terminal assumed to be equipped with a precision approach guidance system. A cross section of pilots participated as test subjects, and despite the high workload level, the results indicated that for the assumptions employed, minimums of 61 m (200 ft) ceiling and 805 m (0.5 mile) visibility were feasible.

Callan, W. M.↗