Search NASA⌕ Search

Engineering topics

Dietderich, D R

Publications and source records attributed to Dietderich, D R.

Test Results of 15 T Nb3Sn Quadrupole Magnet HQ01 with a 120 mm Bore for the LHC Luminosity Upgrade

In support of the luminosity upgrade of the Large Hadron Collider (LHC), the US LHC Accelerator Research Program (LARP) has been developing a 1-meter long, 120 mm bore Nb{sub 3}Sn IR quadrupole magnet (HQ). With a short sample gradient of 219 T/m at 1.9 K and a conductor peak field of 15 T, the magnet will operate under higher forces and stored-energy levels than that of any previous LARP magnet models. In addition, HQ has been designed to incorporate accelerator quality features such as precise coil alignment and adequate cooling. The first 6 coils (out of the 8 fabricated so far) have been assembled and used in two separate tests-HQ01a and HQ01b. This paper presents design parameters, summary of the assemblies, the mechanical behavior as well as the performance of HQ01a and HQ01b.

43 PARTICLE ACCELERATORS↗

Introduction of Nonlinear Properties Into Hierachical Models of Nb3Sn Strands

The development of computational models representing Rutherford cable formation and deformation is necessary to investigate the strain state in the superconducting filaments in Nb{sub 3}Sn magnets. The wide variety of length scales within accelerator magnets suggests usage of a hierarchical structure within the model. As part of an ongoing investigation at LBNL, a three-dimensional simplified nonlinear multiscale model is developed as a way to extend previous linear elastic versions. The inclusion of plasticity models into the problem formulation allows an improved representation of strand behavior compared to the linear elastic model. This formulation is applied to a single Nb{sub 3}Sn strand to find its effective properties as well as the strain state in the conductor under loading.

43 PARTICLE ACCELERATORS↗

Analysis of Bulk and Thin Film Model Samples Intended for Investigating the Strain Sensitivity of Niobium-Tin

Bulk samples and thin films were fabricated and characterized to determine their suitability for studying the effect of composition and morphology on strain sensitivity. Heat capacity and resistivity data are used to determine the critical temperature distribution. It is found that all bulk samples contain stoichiometric Nb{sub 3}Sn regardless of their nominal Nb to Sn ratio. Furthermore, in bulk samples with Cu additions, a bi-modal distribution of stoichiometric and off-stoichiometric Nb-Sn is found. Thus the nominally off-stoichiometric bulk samples require additional homogenization steps to yield homogeneous off-stoichiometric samples. A binary magnetron-sputtered thin film has the intended off-stoichiometric Nb-Sn phase with a mid-point critical temperature of 16.3 K. This type of sample is a suitable candidate for investigating the strain sensitivity of A15 Nb{sub 1-{beta}}Sn{sub {beta}}, with 0.18 < {beta} < 0.25. The strain sensitivity of Nb-Sn as a function of composition and morphology is important for an in-depth understanding of the strain sensitivity of composite Nb{sub 3}Sn wires.

43 PARTICLE ACCELERATORS↗

Numerical Investigation of the Quench Behavior of Bi2Sr2CaCu2Ox Wire

The quench behavior of Bi{sub 2}Sr{sub 2}CaCu{sub 2}O{sub x} (Bi2212) wire is investigated through numerical simulations. This work is part of the U.S. Very High Field Superconducting Magnet Collaboration (VHFSMC). Numerical simulations are carried out using a one-dimensional computational model of thermal transport in Bi2212 composite wires. A quench is simulated by introducing heat in a section of the wire, and the voltage and temperature are monitored as function of time and position. The quench energy, normal zone propagation velocity, and spatial distribution of temperature are calculated for varying transport current and applied magnetic field. The relevance of these simulations in defining criteria for experimental measurements is discussed.

43 PARTICLE ACCELERATORS↗

A Superconducting transformer system for high current cable testing

This article describes the development of a direct-current (dc) superconducting transformer system for the high current test of superconducting cables. The transformer consists of a core-free 10 464 turn primary solenoid which is enclosed by a 6.5 turn secondary. The transformer is designed to deliver a 50 kA dc secondary current at a dc primary current of about 50 A. The secondary current is measured inductively using two toroidal-wound Rogowski coils. The Rogowski coil signal is digitally integrated, resulting in a voltage signal that is proportional to the secondary current. This voltage signal is used to control the secondary current using a feedback loop which automatically compensates for resistive losses in the splices to the superconducting cable samples that are connected to the secondary. The system has been commissioned up to 28 kA secondary current. The reproducibility in the secondary current measurement is better than 0.05% for the relevant current range up to 25 kA. The drift in the secondary current, which results from drift in the digital integrator, is estimated to be below 0.5 A/min. The system's performance is further demonstrated through a voltage-current measurement on a superconducting cable sample at 11 T background magnetic field. The superconducting transformer system enables fast, high resolution, economic, and safe tests of the critical current of superconducting cable samples.

43 PARTICLE ACCELERATORS↗