Search NASA⌕ Search

Engineering topics

Dillman, Robert

Publications and source records attributed to Dillman, Robert.

10 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Human Mars Entry, Descent and Landing Architecture Study: Deployable Decelerators

NASA’s Entry, Descent and Landing Architecture Study uses a trajectory simulation framework to evaluate various technologies and concepts of operations for human scale EDL at Mars. The study results inform agency technology investments. This paper summarizes the design assumptions and analysis of two deployable entry concepts performed in Phase 2 of the study. The entry concepts include a rigid deployable called the Adaptable Deployable Entry Placement Technology and an inflatable concept called the Hypersonic Inflatable Aerodynamic Decelerator. This paper describes the concept operations of these vehicles to deliver a 20-metric ton payload to the surface of Mars. Details of vehicle design and flight performance are summarized along with results of analysis on the aft body heating and its effect on the payload. Finally, recommended technology investments based on the results are presented.

Dwyer Cianciolo, Alicia↗
NASA NTRS2015

Entry Descent and Landing Workshop Proceedings: Inflatable Reentry Vehicle Experiment-3 (IRVE-3) Project Overview & Instrumentation - Volume 1

Entry mass at Mars is limited by the payload size that can be carried by a rigid capsule that can fit inside the launch vehicle fairing. Landing altitude at Mars is limited by ballistic coefficient (mass per area) of entry body. Inflatable technologies allow payload to use full diameter of launch fairing, and deploy larger aeroshell before atmospheric interface, landing more payload at a higher altitude. Also useful for return of large payloads from Low Earth Orbit (LEO).

Dillman, Robert↗
NASA NTRS2014

Planned Flight of the Terrestrial HIAD Orbital Reentry (THOR)

The Terrestrial HIAD Orbital Reentry (THOR) is planned for flight in 2016 as a secondary payload on an Orbital Sciences commercial resupply mission to the International Space Station. THOR will launch with its Hypersonic Inflatable Aerodynamic Decelerator (HIAD) stowed as a small cylinder between the second stage motor and the launch vehicle fairing. Once the Cygnus cargo vehicle has separated from the second stage, THOR will likewise separate, autonomously re-orient itself, perform a deorbit burn, then inflate the HIAD to a 3.5m diameter cone before atmospheric interface. THOR is a follow-on mission to the IRVE-3 flight test of 2012. The high energy of orbital reentry will allow THOR to demonstrate the performance of its improved, second-generation inflatable structure and flexible TPS materials, in a more energetic entry environment than previous suborbital test flights.This paper discusses the sequence of events planned to occur as part of the THOR mission. Specific topics will include the THOR mission concept, reentry vehicle design for the expected flight environment, the on-board sensors that will allow quantification of vehicle performance, and how we intend to retrieve the flight data from a reentry vehicle splashing down in international waters.

Dillman, Robert↗
NASA NTRS2013

Woven Thermal Protection System Based Heat-shield for Extreme Entry Environments Technology (HEEET)

NASA's future robotic missions utilizing an entry system into Venus and the outer planets, namely, Saturn, Uranus, Neptune, result in extremely high entry conditions that exceed the capabilities of state of the art low to mid density ablators such as PICA or Avcoat. Therefore mission planners typically assume the use of a fully dense carbon phenolic heat shield similar to what was flown on Pioneer Venus and Galileo. Carbon phenolic is a robust TPS material however its high density and relatively high thermal conductivity constrain mission planners to steep entries, with high heat fluxes and pressures and short entry durations, in order for CP to be feasible from a mass perspective. The high entry conditions pose challenges for certification in existing ground based test facilities and the longer‐term sustainability of CP will continue to pose challenges. In 2012 the Game Changing Development Program (GCDP) in NASA's Space Technology Mission Directorate funded NASA ARC to investigate the feasibility of a Woven Thermal Protection System (WTPS) to meet the needs of NASA's most challenging entry missions. This project was highly successful demonstrating that a Woven TPS solution compares favorably to CP in performance in simulated reentry environments and provides the opportunity to manufacture graded materials that should result in overall reduced mass solutions and enable a much broader set of missions than does CP. Building off the success of the WTPS project GCDP has funded a follow on project to further mature and scale up the WTPS concept for insertion into future NASA robotic missions. The matured WTPS will address the CP concerns associated with ground based test limitations and sustainability. This presentation will briefly discuss results from the WTPS Project and the plans for WTPS maturation into a heat‐shield for extreme entry environment.

Ellerby, Donald↗
NASA NTRS2013

Flight Performance of the Inflatable Reentry Vehicle Experiment 3

The Inflatable Reentry Vehicle Experiment 3 (IRVE-3) launched July 23, 2012, from NASA Wallops Flight Facility (WFF) on a Black Brant XI suborbital sounding rocket and successfully performed its mission, demonstrating the survivability of a hypersonic inflatable aerodynamic decelerator (HIAD) in the reentry heating environment and also illustrating the effect of an offset center of gravity on the HIAD's lift-to-drag ratio. IRVE-3 was a follow-on to 2009's IRVE-II mission, which demonstrated exo-atmospheric inflation, reentry survivability - without significant heating - and the aerodynamic stability of a HIAD down to subsonic flight conditions. NASA Langley Research Center is leading the development of HIAD technology for use on future interplanetary and Earth reentry missions.

Dillman, Robert↗
NASA NTRS2013

Woven Thermal Protection System Based Heat-shield for Extreme Entry Environments Technology (HEEET)

NASA's future robotic missions utilizing an entry system into Venus and the outer planets, namely, Saturn, Uranus, Neptune, result in extremely severe entry conditions that exceed the capabilities of state of the art low to mid density ablators such as PICA or Avcoat. Therefore mission planners typically assume the use of a fully dense carbon phenolic heat shield similar to what was flown on Pioneer Venus and Galileo. Carbon phenolic (CP) is a robust TPS material however its high density and relatively high thermal conductivity constrain mission planners to steep entries, with high heat fluxes and pressures and short entry durations, in order for CP to be feasible from a mass perspective. The high entry conditions pose challenges for certification in existing ground based test facilities and the longer-­‐term sustainability of CP will continue to pose challenges. In 2012 the Game Changing Development Program (GCDP) in NASA's Space Technology Mission Directorate funded NASA ARC to investigate the feasibility of a Woven Thermal Protection System (WTPS) to meet the needs of NASA's most challenging entry missions. This project was highly successful demonstrating that a Woven TPS solution compares favorably to CP in performance in simulated reentry environments and provides the opportunity to manufacture graded materials that should result in overall reduced mass solutions and enable a much broader set of missions than does CP. Building off the success of the WTPS project GCDP has funded a follow on project to further mature and scale up the WTPS concept for insertion into future NASA robotic missions. The matured WTPS will address the CP concerns associated with ground based test limitations and sustainability. This presentation will briefly discuss results from the WTPS Project and the plans for WTPS maturation into a heat-­‐shield for extreme entry environment.

Chinnapongse, Ronald↗
NASA NTRS2008

Overview of the Mars Sample Return Earth Entry Vehicle

NASA's Mars Sample Return (MSR) project will bring Mars surface and atmosphere samples back to Earth for detailed examination. Langley Research Center's MSR Earth Entry Vehicle (EEV) is a core part of the mission, protecting the sample container during atmospheric entry, descent, and landing. Planetary protection requirements demand a higher reliability from the EEV than for any previous planetary entry vehicle. An overview of the EEV design and preliminary analysis is presented, with a follow-on discussion of recommended future design trade studies to be performed over the next several years in support of an MSR launch in 2018 or 2020. Planned topics include vehicle size for impact protection of a range of sample container sizes, outer mold line changes to achieve surface sterilization during re-entry, micrometeoroid protection, aerodynamic stability, thermal protection, and structural materials selection.

Dillman, Robert↗
NASA NTRS2005

Development and Test Plans for the MSR EEV

The goal of the proposed Mars Sample Return mission is to bring samples from the surface of Mars back to Earth for thorough examination and analysis. The Earth Entry Vehicle is the passive entry body designed to protect the sample container from entry heating and deceleration loads during descent through the Earth s atmosphere to a recoverable location on the surface. This paper summarizes the entry vehicle design and outlines the subsystem development and testing currently planned in preparation for an entry vehicle flight test in 2010 and mission launch in 2013. Planned efforts are discussed for the areas of the thermal protection system, vehicle trajectory, aerodynamics and aerothermodynamics, impact energy absorption, structure and mechanisms, and the entry vehicle flight test.

Dillman, Robert↗
NASA NTRS1989

Lunar lander conceptual design

A conceptual design is presented of a Lunar Lander, which can be the primary vehicle to transport the equipment necessary to establish a surface lunar base, the crew that will man the base, and the raw materials which the Lunar Station will process. A Lunar Lander will be needed to operate in the regime between the lunar surface and low lunar orbit (LLO), up to 200 km. This lander is intended for the establishment and operation of a manned surface base on the moon and for the support of the Lunar Space Station. The lander will be able to fulfill the requirements of 3 basic missions: A mission dedicated to delivering maximum payload for setting up the initial lunar base; Multiple missions between LLO and lunar surface dedicated to crew rotation; and Multiple missions dedicated to cargo shipments within the regime of lunar surface and LLO. A complete set of structural specifications is given.

Lee, Joo Ahn↗