Search NASA⌕ Search

Engineering topics

Dillon, J. L.

Publications and source records attributed to Dillon, J. L..

13 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1986

The NASA-Langley 20-inch supersonic wind tunnel

NASA Langley's new 20-inch supersonic wind tunnel is in the process of reassembly, following extensive modifications. These will result in its incorporation of such features as a 'quiet' flow control valve, thick sintered screens with very large pressure drops, special farings in the contraction section, an instantaneous relief hatch in the test section, and a switching exhaust system that permits flow into a vacuum sphere during startup and shutdown and to the atmosphere during data acquisition. Attention is given to the expected operating map of the new tunnel.

Dillon, J. L.↗
NASA NTRS1985

Correlation and analysis of oil flow data for an air-breathing missile model

This paper will present the results of an oil flow investigation on an airbreathing missile model. This oil flow study examined the flow around the model, which can be configured with both axisymmetric and two-dimensional inlets. Flow visualization analyses were conducted for both types of geometries by examining the surface flow patterns made visible by the oil flows for Mach numbers of 2.5 and 3.95. The analysis has shown the extent of flow spillage around the inlet which has helped explain the force and moment data collected during previous testing of the model. The oil flow data has also been used to develop guidelines for modeling the location of the crossflow separation line along inlet fairings. Finally, the oil flow analysis has been used to identify unique features of the boattail flow. These boattail flow characteristics have been correlated with previous oil flow analysis of noncircular body models. This paper demonstrates the use of this type of oil flow analysis in developing missile flow field analysis and aerodynamic predictions ranging from impact angle methods through Navier-Stokes methods.

Stoy, S. L.↗
NASA NTRS1982

Hypersonic airbreathing missile concepts under study at NASA Langley Research Center

The design and performance of several tactical and strategic hypersonic airbreathing missile concepts under study at the NASA Langley Research Center are discussed from an evolutionary perspective. A mid- and chin inlet missile design, constrained to the Navy's vertical box launcher, was investigated; a performance comparison is presented that is favorable to the mid-inlet approach. Parasol wing, confined flow field, and spatula-like cruise missile configurations were examined with strategic applications in mind. The preliminary results are encouraging with respect to aerodynamic and volumetric efficiency and choice of engine integration schemes.

Hunt, J. L.↗
NASA NTRS1980

Aerodynamic and inlet flow characteristics of several hypersonic airbreathing missile concepts

Four conceptual hypersonic missile configurations were examined experimentally and theoretically. Two of the concepts employed twin module bottom-mounted engines and two were designed for upper surface inlets or engines with the intent of reducing the vehicle observables. The tests were conducted at Mach 6 and Reynolds numbers of 6 to 7.5 x 10 to the 6th per foot. Flow field surveys in the vicinity of the engine inlet were made on all configurations and force and moment tests were conducted on three of the vehicles. Stability and control characteristics of the bottom-mounted engine configurations which incorporated slender, low wings were dominated by strong vortices that promoted severe pitchup tendencies. The shock layer and flow quality in the vicinity of the bottom-mounted engine inlets were dependent on nose shape. The spatula-like upper surface engine concept demonstrated good performance and had uniform flow entering the engine inlet, while the upper surface inlet concept with a highly swept forebody incurred large gradients due to interactions with leading edge shocks.

Dillon, J. L.↗
NASA NTRS1979

Aerodynamic characteristics of a hypersonic research airplane concept having a 70 deg swept double-delta wing at Mach numbers from 0.80 to 1.20, with summary of data from 0.20 to 6.0

The static longitudinal, lateral, and directional stability characteristics of a hypersonic research airplane concept having a 70 deg swept double-delta wing were investigated. Force tests were conducted in the Langley 8 foot transonic pressure tunnel for a Reynolds number (based on fuselage length) range of 6.30 x 10 to the 6th power to 7.03 x 10 to the 6th power, at angles of attack from about -4 deg to 23 deg, and at angles of sideslip of 0 deg and 5 deg. The configuration variables included the wing planform, tip fins, the center vertical tail, and scramjet engine modules. Variations of the more important aerodynamic parameters with Mach number for Mach numbers from 0.20 to 6.0 are summarized. A state-of-the-art example of theoretically predicting performance parameters and static longitudinal and directional stability over the Mach number range is included.

Penland, J. A.↗
NASA NTRS1978

Aerodynamic characteristics of a hypersonic research airplane concept having a 70 deg swept double-delta wing at Mach number 0.2

A wind-tunnel of the static longitudinal, lateral and directional stability characteristics of a hypersonic research airplane concept having a 70 deg swept double-delta wing was conducted in the Langley low-turbulence pressure tunnel. The configuration variables included wing planform, tip fins, center fin, and scramjet engine modules. A mach number of 0.2 was investigated over a Reynolds number (based on fuselage length) range of 2,200,000 to 19.75 x 1,000,000 (with a majority of tests at 10.0 x 1,000,000. Tests were conducted through an angle-of-attack range from about -2 deg to 34 deg at angles of sideslip of 0 deg to 5 deg, and at elevon deflection of 0 deg, -5 deg, -10 deg, -15 deg, and -20 deg. The drag coefficient of the integrated scramjet engine appears relatively constant with Reynolds number at the test Mach number of 0.2. Mild pitch-up was exhibited by the models equipped with tip fins. The forward delta, a highly swept forward portion of the wing, was destabilizing. The center fin model has a higher trimmed maximum lift-drag ratio and a wider trim lift and angle-of-attack range than the tip fin model. Both the tip fin models and center fin models exhibited positive dihedral effect and positive directional stability. Roll control was positive for the tip fin model, but yaw due to roll control was unfavorable.

Penland, J. A.↗
NASA NTRS1978

Aerodynamic characteristics at Mach 6 of a wing-body concept for a hypersonic research airplane

The static aerodynamic characteristics of a 1/30 scale model of a wing-body concept for a high speed research airplane were investigated in the Langley 20 inch Mach six tunnel. The investigation consisted of configuration buildup from the basic body by adding a wing, center vertical tail, three-module scramjet, and six-module scramjet engine. The test Mach number was six at a Reynolds number, based on model fuselage length, of about 13,700,000. The test angle-of-attack range was 4 to 20 D at constant angles of sideslip of 0, 2, and 4 deg. The elevons were deflected from 10 to -15 D for pitch control. Roll and yaw control were investigated. Experimental aerodynamic characteristics are compared with analytical elements.

Dillon, J. L.↗
NASA NTRS1978

Aerodynamic characteristics at Mach number 0.2 of a wing-body concept for a hypersonic research airplane

The static aerodynamic characteristics were studied on a model wing-body concept for a high-speed research airplane in a low-turbulence pressure tunnel. The experiment consisted of configuration buildup from the basic body by adding a wing, center vertical tail, three-module scramjet, and six-module scramjet engine. The test Mach number was 0.2 at Reynolds numbers, based on fuselage length, ranging from 2.78 x 1 million to 23 x 2 million. The test angle-of-attack range was approximately -5 to 30 deg at constant angles of sideslip of 0 deg and 4 deg. The elevons were deflected from 5 deg to -15 deg. Roll and yaw control were investigated.

Dillon, J. L.↗
NASA NTRS1978

An aerodynamic analysis of several hypersonic research airplane concepts from M = 0.2 to 6.0

Several conceptual hypersonic research airplanes, designed within the constraints of a B-52 launch aircraft, have been studied experimentally and analytically at Mach numbers from 0.2 to 6.0. Vehicles built to these criteria for Mach 6 cruise were shown to be feasible, if careful attention was paid to the low speed lift, drag, and high angle of attack stability to assure successful landings and transonic pitch angle maneuvers. The integrated scramjet engine drag was high at subsonic speeds and appears to be constant with Reynolds number. The variable geometry airfoil used previously to improve directional stability was shown to be equally adaptable to the improvement of longitudinal stability. The vortex lattice theory gave good subsonic predictions of lift, drag due to lift, and pitching moments. Wind tunnel tests must be relied on for the drag at zero lift, trim, static margins and lateral-directional stability. The Gentry Hypersonic Arbitrary Body Program gave good predictions of the trends of lift, drag, and pitching moments with angle of attack at Mach numbers above 3, but the level of the values were not consistently predicted. No currently available theory or program gave accurate predictions of directional stability or dihedral effects at hypersonic speeds.

Penland, J. A.↗
NASA NTRS1977

Aerodynamic characteristics at Mach numbers from 0.33 to 1.20 of a wing-body design concept for a hypersonic research airplane

An experimental investigation of the static aerodynamic characteristics of a model of one design concept for the proposed National Hypersonic Flight Research Facility was conducted in the Langley 8 foot transonic pressure tunnel. The experiment consisted of configuration buildup from the basic body by adding a wing, center vertical tail, and a three module or six module scramjet engine. The freestream test Mach numbers were 0.33, 0.80, 0.90, 0.95, 0.98, 1.10, and 1.20 at Reynolds numbers per meter ranging from 4.8 x 1 million to 10.4 x 1 million. The test angle of attack range was approximately -4 deg to 22 deg at constant angles of sideslip of 0 deg and 4 deg; the angle of sideslip ranged from about -6 deg to 6 deg at constant angles of attack of 0 deg and 17 deg. The elevons were deflected 0 deg, -10 deg, and -20 deg with rudder deflections of 0 deg and 15.6 deg.

Dillon, J. L.↗
NASA NTRS1977

Vortex lattice prediction of subsonic aerodynamics of hypersonic vehicle concepts

The vortex lattice method introduced by Lamar and Gloss (1975) was applied to the prediction of subsonic aerodynamic characteristics of hypersonic body-wing configurations. The reliability of the method was assessed through comparison of the calculated and observed aerodynamic performances of two National Hypersonic Flight Research Facility craft at Mach 0.2. The investigation indicated that a vortex lattice model involving 120 or more panel elements can give good results for the lift and induced drag coefficients of the craft, as well as for the pitching moment at angles of attack below 10 to 15 deg. Automated processes for calculating the local slopes of mean-camber surfaces may also render the method suitable for use in preliminary design phases.

Pittman, J. L.↗