Search NASA⌕ Search

Engineering topics

Dillon, Shen J.

Publications and source records attributed to Dillon, Shen J..

At least 19 records

Creep and failure at metal-oxide interfaces

Small-scale bicrystal creep experiments were performed on contacts formed via in situ high-temperature diffusion bonding of metal-oxide interfaces including Ag-ZrO 2 , Pd-ZrO 2 , Pt-ZrO 2 , and Ag-high entropy oxide. This work characterizes deformation and failure at metal-oxide interfaces during mechanical loading. Interfacial sliding can be activated easily, while tensile interfacial creep was not observed at any condition of stress or temperature measured. Plastic strain, instead, localizes within the metal under tensile loading. A variety of mechanisms for plastic strain occur in the metal including lattice dislocation-mediated plasticity, twinning, low-angle grain boundary formation, and low-angle grain boundary creep. Surface and low-angle grain boundary diffusion occur under conditions where no metal-oxide tensile creep is observed, highlighting the significant differences in their interfacial mechanical response. High-temperature interfacial failure occurs when the mean curvature at the contact neck is approximately zero and the applied stresses comparable to brittle fracture stresses. The brittle fracture stresses were measured to be σ ƒ = 180 ± 90 MPa at the Ag-ZrO 2 interface at 225 °C, σ ƒ = 460 ± 160 MPa at the Pd-ZrO 2 interface at 680 °C, and σ ƒ = 640 ± 440 MPa at the Pt-ZrO 2 interface at 1010 °C.

Creep↗

Assessing cathode–electrolyte interphases in batteries

The cathode-electrolyte interphase plays a pivotal role in determining the usable capacity and cycling stability of electrochemical cells, yet it is overshadowed by its counterpart, the solid-electrolyte interphase. This is primarily due to the prevalence of side reactions, particularly at low potentials on the negative electrode, especially in state-of-the-art Li-ion batteries where the charge cutoff voltage is limited. However, as the quest for high-energy battery technologies intensifies, there is a pressing need to advance the study of cathode-electrolyte interphase properties. Here, we present a comprehensive approach to analyse the cathode-electrolyte interphase in battery systems. We underscore the importance of employing model cathode materials and coin cell protocols to establish baseline performance. Additionally, we delve into the factors behind the inconsistent and occasionally controversial findings related to the cathode-electrolyte interphase. In conclusion, we also address the challenges and opportunities in characterizing and simulating the cathode-electrolyte interphase, offering potential solutions to enhance its relevance to real-world applications.

25 ENERGY STORAGE↗

Using in situ UO 2 bicrystal sintering to understand grain boundary dislocation nucleation kinetics and creep

Capillary evolution at bicrystal UO 2 grain boundaries is characterized using in situ transmission electron microscopy. The discontinuous nature of the densification process, both particle rotation and axial strain, along with the large activation stress for densification support a hypothesis that grain boundary strain in UO 2 follows nucleation rate limited kinetics at low to intermediate stresses, that is, less than ≈ 10 8 PA. Further, the temperature dependence of the average activation stress for sintering agrees well with analysis of bulk sintering data and creep data reported within the literature when analyzed in the context of a grain boundary dislocation nucleation rate limited kinetic model.

36 MATERIALS SCIENCE↗

Ultrahigh temperature in situ transmission electron microscopy based bicrystal coble creep in zirconia I: Nanowire growth and interfacial diffusivity

This study demonstrates novel in situ transmission electron microscopy-based microscale single grain boundary Coble creep experiments used to grow nanowires through a solid-state process in cubic ZrO 2 between ≈ 1200 °C and ≈ 2100 °C. Experiments indicate Coble creep drives the formation of nanowires from asperity contacts during tensile displacement, which is confirmed by phase field simulations. The experiments also facilitate efficient measurement of grain boundary diffusivity and surface diffusivity. 10 mol% Sc 2 O 3 doped ZrO 2 is found to have a cation grain boundary diffusivity of $D_{gb} = (0.056 ± 0.05)exp (\frac{-380,000±41,000}{RT})m^2 s^{-1}$, and $D_s = (0.10 ± 0.27)exp(\frac{-380,000 ± 28,000}{RT}) m^2 s^{-1}$.

36 MATERIALS SCIENCE↗

Ultrahigh temperature in situ transmission electron microscopy based bicrystal coble creep in Zirconia II: Interfacial thermodynamics and transport mechanisms

This work uses a combination of stress dependent single grain boundary Coble creep and zero-creep experiments to measure interfacial energies, along with grain boundary point defect formation and migration volumes in cubic ZrO 2 . These data, along with interfacial diffusivities measured in a companion paper are then applied to analyzing two-particle sintering. The analysis presented here indicates that the large activation volume, v * = v f + v m primarily derives from a large migration volume and suggests that the grain boundary rate limiting defects are delocalized, possibly due to electrostatic interactions between charge compensating defects. The discrete nature of the sintering and creep process observed in the small-scale experiments supports the hypothesis that grain boundary dislocations serve as sources and sinks for grain boundary point defects and facilitate strain during sintering and Coble creep. Model two-particle sintering experiments demonstrate that initial-stage densification follows interface reaction rate-limited kinetics.

36 MATERIALS SCIENCE↗

Irradiation induced creep in nanocrystalline high entropy alloys

Irradiation induced creep (IIC) compliance in NiCoFeCrMn high entropy alloys is measured as a function of grain size (30 < x < 80 nm) and temperature (23–500 °C). For 2.6 MeV Ag 3+ irradiation at a dose rate of 1.5×10 – 3 dpa – 1 s – 1 the transition from the recombination to sink limited regimes occurs at ~ 100 °C. In the sink-limited regime, the IIC compliance scales inversely with grain size, consistent with a recently proposed model for grain boundary IIC. The thermal creep rate is also measured; it does not become comparable to the IIC rate, however, until ~ 650 °C. Here, the results are discussed in context of defect kinetics in irradiated HEA systems.

36 MATERIALS SCIENCE↗

High temperature irradiation induced creep in Ag nanopillars measured via in situ transmission electron microscopy

Irradiation induced creep (IIC) rates are measured in compression on Ag nanopillar (square) beams in the sink-limited regime. The IIC rate increases linearly with stress at lower stresses, i.e. below ≈2/3 the high temperature yield stress and parabolically with pillar width, L, for L less than ≈300 nm. Here, the data are obtained by combining in situ transmission electron imaging with simultaneous ion irradiation, laser heating, and nanopillar compression. Results in the larger width regime are consistent with prior literature.

36 MATERIALS SCIENCE↗

Final Report: In-Situ TEM Observations of Degradation Mechanisms in Next-Generation High-Energy Density Lithium-Ion Battery Systems

This project originally sought to characterize nanoscale processes associated with the degradation of next-generation high energy density lithium-ion battery electrodes via in-situ transmission electron microscopy (TEM). The research also focused on developing the experimental techniques necessary for investigating electrochemical systems by in-situ transmission electron microscopy and providing a framework for understanding and quantifying electron beam effects that influence experimental results. In line with these goals, this project demonstrated and published the first in-situ TEM cycling of a Li-ion battery electrode in commercially relevant non-aqueous electrolyte: a technique subsequently adopted by a number of researchers in the field. Experiments performed on Sn anodes, demonstrated porosity evolution during Li dealloying as a mechanism for strain accommodation during the first cycle, and observed partially reversible crystalline to amorphous phase transitions associated with Li insertion and extraction in subsequent cycles. Complementary study of in-situ dealloying in a simple model, Au-Cu, was also performed. We also published the earliest quantitative measurements of electron beam effects in aqueous and non-aqueous liquids. Specifically, we utilized a model system to quantify the fraction of incident electron beam that contributed to charge transfer mediated reactions in non-aqueous liquid, since such liquids are primarily dose sensitive. We also quantified the evolution of model aqueous chemistries as a function of dose rate and chemical potential to better understand the reaction mechanisms active in liquids exposed to electron beams. The original project goals included the use of controlled environments to simulate different battery operational conditions. To aid such experiments, we developed new experimental apparatuses and techniques to perform in-situ liquid cell TEM under controlled temperature, including heating and cooling. We demonstrated this capability in aqueous systems; specifically understanding phase selection and solid-liquid interface interactions with particles during water crystallization and hydrothermal precipitation kinetics of ZnO. We also published the first demonstration of in-situ TEM based high-field (plasma) experiments and in-situ TEM of aqueous photochemistry, which demonstrated an previously unrecognized early growth mode transition during Au sputtering and delocalization of gas bubble nucleation during water splitting, respectively. In addition to the scientific results, this portion of the project greatly expanded the range of systems that can be characterized in realistic environments at the nanoscale via in-situ TEM. Unfortunately, commercial battery electrolytes are quite sensitive to electron dose. This limits the time of acquisition and/or the spatial resolution of the experiments. The same problem has been encountered in all subsequent publications in the field. The major problem, relative to the project original goals, is that long term cycling is challenging to characterize and the desired high resolution or analytical capabilities are limited. In line with our original goals to characterize battery reaction and degradation mechanisms under controlled electrochemical cycling, we developed a completely new type of Li-ion electrochemical cell that has been useful for both structural and analytical characterization. To date, we have demonstrated this platform for in-situ cycling of Li-ion batteries during scanning electron microscopy (SEM), Auger electron spectroscopy (AES), and x-ray photoelectron spectroscopy (XPS). In-situ AES has been found to be a quite powerful tool to characterize the chemical evolution of Li-ion batteries cycled in-situ and much of our effort in the final project period has focused on charactering Li-ion cathodes using the technique. We utilized in-situ SEM to propose a new mechanism for Li whisker/dendrite formation and show the importance of diffusion mediated stress relaxation in fracture of Sn anode particles. A combination of in-situ XPS and AES was used to clarify the CuO anode reaction mechanism. In the final project period, we have gained new insights into surface reactions occurring on cathodes at high voltage using in-situ AES. Specifically, we have discovered that many of the SEI formation reactions typically attributed to electrolyte decomposition are actually more fundamental to the electrode material surface thermodynamics in the presence of an arbitrary carbon source. These insights greatly affect how we understand and control surface degradation induced capacity fade at cathodes. Finally, we have made some effort to apply this novel in-situ platform to TEM characterization and believe this is a fruitful avenue for future research.

25 ENERGY STORAGE↗

LiMn 2 O 4 Surface Chemistry Evolution during Cycling Revealed by in Situ Auger Electron Spectroscopy and X-ray Photoelectron Spectroscopy

This work utilizes in situ electrochemical and analytical characterization during cycling of LiMn 2 O 4 (LMO) equilibrated at different potentials in an ultrahigh vacuum (UHV) environment. The LMO reacts with organic molecules in the vacuum to form a high surface concentration of Li 2 CO 3 (≈50% C) during initial charging to 4.05 V. Charging to higher potentials reduces the overall Li 2 CO 3 concentration (≈15% C). Discharging to 3.0 V increases the Li 2 CO 3 concentration (≈30% C) and over discharging to 0.1 V again reduces its concentration (≈15% C). This behavior is reproducible over 5 cycles. The model geometry utilized suggests that oxygen from LMO can participate in redox of carbon, where LMO contributes oxygen to form the carbonate in the solid electrolyte interphase (SEI). Similar results were obtained from samples cycled ex situ , suggesting that the model in situ geometry provides reasonably representative information about surface chemistry evolution. Finally, carbon redox at LMO and the inherent voltage instability of the Li 2 CO 3 likely contributes significantly to its capacity fade.

25 ENERGY STORAGE↗

Improved Performance in FeF 2 Conversion Cathodes through Use of a Conductive 3D Scaffold and Al 2 O 3 ALD Coating

FeF 2 is considered a promising conversion compound for the positive electrode in lithium-ion batteries due to its high thermodynamic reduction potential (2.66 V vs Li/Li + ) and high theoretical specific capacity (571 mA h g -1 ). However, the sluggish reaction kinetics and rapid capacity decay caused by side reactions during cycling limit its practical application. Here, the fabrication of Ni-supported 3D Al 2 O 3 -coated FeF 2 electrodes is presented, and it is shown that these structured electrodes significantly overcome these limitations. The electrodes are prepared by iron electrodeposition on a Ni support, followed by a facile fluorination process and Al 2 O 3 coating by atomic layer deposition. The 3D FeF 2 electrode delivers an initial discharge capacity of 380 mA h g -1 at a current density of 200 mA g -1 at room temperature. The 3D scaffold improves the reaction kinetics and enables a high specific capacity by providing an efficient electron pathway to the insulating FeF 2 and short Li diffusion lengths. The Al 2 O 3 coating significantly improves the cycle life, probably by preventing side reactions through limiting direct electrode–electrolyte contact. The fabrication method presented here can also be applied for synthesis of other metal fluoride materials on different 3D conductive templates.

25 ENERGY STORAGE↗

Irradiation-induced creep in metallic nanolaminates characterized by In situ TEM pillar nanocompression

Our work reports on irradiation-induced creep (IIC) measured on nanolaminate (Cu-W and Ni-Ag) and nanocrystalline alloys (Cu-W) at room temperature using a combination of heavy ion irradiation and nanopillar compression performed concurrently in situ in a transmission electron microscope. Furthermore, we observed appreciable IIC in multilayers with 50 nm layer thicknesses at high stress, ≈½ the yield strength, but not in multilayers with only 5 nm layer thicknesses.

36 MATERIALS SCIENCE↗

Large-deformation and high-strength amorphous porous carbon nanospheres

Carbon is one of the most important materials extensively used in industry and our daily life. Crystalline carbon materials such as carbon nanotubes and graphene possess ultrahigh strength and toughness. In contrast, amorphous carbon is known to be very brittle and can sustain little compressive deformation. Inspired by biological shells and honeycomb-like cellular structures in nature, we introduce a class of hybrid structural designs and demonstrate that amorphous porous carbon nanospheres with a thin outer shell can simultaneously achieve high strength and sustain large deformation. The amorphous carbon nanospheres were synthesized via a low-cost, scalable and structure-controllable ultrasonic spray pyrolysis approach using energetic carbon precursors. In situ compression experiments on individual nanospheres show that the amorphous carbon nanospheres with an optimized structure can sustain beyond 50% compressive strain. Both experiments and finite element analyses reveal that the buckling deformation of the outer spherical shell dominates the improvement of strength while the collapse of inner nanoscale pores driven by twisting, rotation, buckling and bending of pore walls contributes to the large deformation.

36 MATERIALS SCIENCE↗

Mechano-Electrochemical Interaction Gives Rise to Strain Relaxation in Sn Electrodes

Tin (Sn) anode active particles were electrochemically lithiated during simultaneous imaging in a scanning electron microscope. Relationships among the reaction mechanism, active particle local strain rate, particle size, and microcrack formation are elucidated to demonstrate the importance of strain relaxation due to mechano-electrochemical interaction in Sn-based electrodes under electrochemical cycling. At low rates of operation, due to significant creep relaxation, large Sn active particles, of size 1 μm, exhibit no significant surface crack formation. Microcrack formation within Sn active particles occurs due to two different mechanisms: (i)large concentration gradient induced stress at the two-phase interface, and (ii) high volume expansion induced stress at the surface of the active particles. From the present study, it can be concluded that majority of the microcracks evolve at or near the particle surface due to high volume expansion induced tension. Concentration gradient induced damage prevails near the center of the active particle, though significantly smaller in magnitude. Comparison with experimental results indicates that at operating conditions of C/2, even 500 nm sized Sn active particles remain free from surface crack formation, which emphasizes the importance of creep relaxation. A phase map has been developed to demonstrate the preferred mechano-electrochemical window of operation of Sn-based electrodes.

25 ENERGY STORAGE↗