Dimitri Mavris | Search NASA

NASA NTRS2023

Modeling and Simulation of a Parallel Hybrid-Electric Propulsion System - Electrified Powertrain Flight Demonstration (EPFD) Program

Electrified aircraft propulsion concepts have been proposed to meet aggressive future performance and environmental goals for the next generation of aircraft. However, electrified aircraft present a unique modeling and simulation challenge as they introduce multiple energy sources to the propulsion system, providing various means to meet thrust requirements, compared to conventional gas turbine propulsion architectures where only fuel is available. Additionally, the introduction of an electric powertrain to the existing system enables multiple electrified flight modes to exist (i.e. eTaxi, climb boost, takeoff boost, etc.), further increasing the complexity of the modeling environment. As part of the Electrified Powertrain Flight Demonstration program, this paper presents a modeling and simulation framework for a parallel hybrid-electric propulsion concept using the Environmental Design Space simulation tool. Electrical components are modeled in NPSS, and an overall sizing methodology is introduced. Finally, various operational modes of the electric powertrain are modeled and tested and their impact on key performance parameters is evaluated.

hybrid electric propulsion↗

NASA NTRS2021

Reliability and Safety Assessment of Urban Air Mobility Concept Vehicles

The primary objective of this research effort is to identify failure modes and hazards associated with several configurations of multicopter concept vehicles supplied by NASA. Functional hazard analyses (FHA) and failure modes and effects criticality analyses (FMECA) are performed for each of the eight vehicle configurations under review. Conceptual design of notional powertrain configurations (turboshaft, electric, hybrid electric), notional thrust control systems (rpm control and collective control), and navigation control systems for the concept vehicles were to support the reliability and safety analysis and to assess whether a mission can be completed safely. Two kinds of analyses are performed: static safety analysis which enable the quantification of the likelihood of individual events, and dynamic safety analyses which allows the investigation of multiple time-dependent failures. Their objective is to quantify the likelihood of catastrophic failures.

Urban Air Mobility↗

NASA NTRSDate not supplied

Development of a Lunar Lander Modeling and Simulation Capability

The development and validation of a capability to perform quantitative, physics-based analysis of alternatives of conceptual unmanned, reusable lunar cargo lander architectures is discussed. The lander is conceptualized as a suite of disciplines that need to be sized, synthesized, and optimized for a mission. As such, models of these disciplines were developed and integrated in a recently-developed multi-disciplinary analysis and optimization framework for space systems. The development of the disciplines, as well as how they are integrated into the framework, is discussed. Additionally, validation studies were performed against the Descent Module of the Altair lunar lander. Finally, an example problem for an uncrewed, reusable lander is presented.

Eugina Mendez Ramos↗

NASA NTRSDate not supplied

The Effectiveness of Power Distribution Systems for Deployment on the Lunar Surface

Lunar habitation missions are currently being planned to have astronauts return to the moon by the mid 2020’s with a sustained lunar presence by the end of the decade. The various landed modules needed to support the missions are expected to be distributed around Shackleton Crater at distances ranging from 1 to 15 km and with power needs ranging from 10 kW to 50kW. Current plans call for a solar array to be installed on the rim of the crater that receives near-constant sunlight year around with a power distribution system that transfers power from the source to consumers. This paper details several power distribution systems: DC transmission lines, radio frequency power beaming, and optical power beaming. Sizing algorithms for each of these distributions systems along with their necessary subsystems were developed from literature and subject matter expertise input. Several experiments were then conducted to determine the performance of the systems along with their sensitivities to changes in assumptions for various sub-components. The defined Figures of Merit enable mission designers to select the best power distribution system for each possible power consumer mission scenario. The experimental results were analyzed and compiled into a set of figures that highlight the conditions for which a certain system outperforms the other.

Bradford Robertson↗

NASA NTRSDate not supplied

Development of a Lunar Lander Modeling and Simulation Capability

The development and validation of a capability to perform quantitative, physics-based analysis of alternatives of conceptual unmanned, reusable lunar cargo lander architectures is discussed. The lander is conceptualized as a suite of disciplines that need to be sized, synthesized, and optimized for a mission. As such, models of these disciplines were developed and integrated in a recently-developed multi-disciplinary analysis and optimization framework for space systems. The development of the disciplines, as well as how they are integrated into the framework, is discussed. Additionally, validation studies were performed against the Descent Module of the Altair lunar lander. Finally, an example problem for an uncrewed, reusable lander is presented.

Eugina Mendez Ramos↗

NASA NTRSDate not supplied

Development of a Lunar Lander Modeling and Simulation Capability

The development and validation of a capability to perform quantitative, physics-based analysis of alternatives of conceptual unmanned, reusable lunar cargo lander architectures is discussed. The lander is conceptualized as a suite of disciplines that need to be sized, synthesized, and optimized for a mission. As such, models of these disciplines were developed and integrated in a recently-developed multi-disciplinary analysis and optimization framework for space systems. The development of the disciplines, as well as how they are integrated into the framework, is discussed. Additionally, validation studies were performed against the Descent Module of the Altair lunar lander. Finally, an example problem for an uncrewed, reusable lander is presented.

Eugina Mendez Ramos↗

NASA NTRSDate not supplied

A Methodology for Actuating RCS Jets in a Continuous, Time-Accurate CFD Simulation

Computational fluid dynamics simulations of Mars entry vehicle reaction control systems have been used to gain a better understanding of the wide range of flow phenomena encountered during various phases of flight. One aspect of this is simulating the system during controlled flight. Current practices model the system in a continuously actuated state, but this methodology is unable to accurately model the dynamic behavior of the system during EDL. One method to improve this is to create a coupled CFD-RBD-Control simulation. The first step to this is establishing a method of accurately actuating an RCS jet during a time accurate CFD simulation. This paper presents a method to achieve this actuation. There are three phases to the methodology: establishing the off state, creating a ramping function that will initialize the jet flow, and establishing the on state. A test case of a jet in a supersonic crossflow is implemented to establish the success of the methodology in being able to actuate a jet in the midst of an ongoing CFD simulation. It shows significant improvement in boundary condition responsiveness for linear and exponential ramping functions in comparison to the step function. A preliminary demonstration of the methodology is presented for the MSL vehicle which shows significant advantages for the implementation of a linear ramping function over a step function.

Alexandra Hickey↗

NASA NTRSDate not supplied

A Methodology for Actuating RCS Jets in a Continuous, Time-Accurate CFD Simulation

Computational fluid dynamics simulations of Mars entry vehicle reaction control systems have been used to gain a better understanding of the wide range of flow phenomena encountered during various phases of flight. One aspect of this is simulating the system during controlled flight. Current practices model the system in a continuously actuated state, but this methodology is unable to accurately model the dynamic behavior of the system during EDL. One method to improve this is to create a coupled CFD-RBD-Control simulation. The first step to this is establishing a method of accurately actuating an RCS jet during a time accurate CFD simulation. This paper presents a method to achieve this actuation. There are three phases to the methodology: establishing the off state, creating a ramping function that will initialize the jet flow, and establishing the on state. A test case of a jet in a supersonic crossflow is implemented to establish the success of the methodology in being able to actuate a jet in the midst of an ongoing CFD simulation. It shows significant improvement in boundary condition responsiveness for linear and exponential ramping functions in comparison to the step function. A preliminary demonstration of the methodology is presented for the MSL vehicle which shows significant advantages for the implementation of a linear ramping function over a step function.

Alexandra Hickey↗

NASA NTRSDate not supplied

Advanced 2030 Single Aisle Aircraft Modeling for the Electrified Powertrain Flight Demonstration Program

The NASA Electrified Powertrain Flight Demonstration Program is aimed at advancing electrified powertrains for future aircraft platforms through flight demonstrations for various passenger classes and power levels. The objective of this paper is to establish non-electrified reference models for 2030 aircraft with advanced technologies for the large single aisle (150 passenger) and small single aisle (100 passenger) vehicle classes. Current state-of-art aircraft are first identified and modeled using a proprietary design tool called Environmental Design Space. Next, through a comprehensive literature review, engine, airframe and composite material technologies that are expected to be available by 2030 are identified, and their respective benefits are applied to the 2030 vehicles. The engine cycle and the aircraft design are then optimized to provide the maximum fuel burn benefit while meeting all the specified aircraft requirements. While the large single aisle aircraft range requirement is kept the same as the current state-of-art aircraft, the small single aisle aircraft is optimized for a reduced range of 1000 nmi. Expected fuel burn benefit from these technologies along with any propulsive, aerodynamic and weight benefit will be summarized in this paper.

single aisle aircraft↗

NASA NTRSDate not supplied

Closed-Loop Simulations of Human-Scale Mars Lander Descent Trajectories on Frontier

A computational campaign was performed to run high-fidelity, free-flight simulations of a human-scale Mars lander concept vehicle decelerating under retropropulsion through the Martian atmosphere with closed-loop flight control. A novel approach is used to couple computational fluid dynamics (CFD) software with a mature flight mechanics package, where the two applications communicate in real-time across two geographically-dispersed computational facilities. The CFD is performed on the Frontier exascale system located at Oak Ridge National Laboratory, and the flight mechanics are executed on a system located at NASA Langley Research Center. In the current campaign, CFD is performed using finite-rate chemistry to account for the interactions between the LOXCH 4 engines and the CO 2 Martian atmosphere. A simulation of a closed-loop main engine throttling and RCS actuation is presented, demonstrating that the vehicle and model are able to maintain stability in a long-duration CFD-in-the-loop flight simulation. Comparisons are made to a reduced order model ignoring aero-propulsive interactions.

CFD↗