Search NASA⌕ Search

Engineering topics

Ding, Kan

Publications and source records attributed to Ding, Kan.

14 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Optimized Incorporation of Furan into Diketopyrrolopyrrole-Based Conjugated Polymers for Organic Field-Effect Transistors

Flexible electronics have received considerable attention in the past decades due to their promising application in rollable display screens, wearable devices, implantable devices, and other electronic applications. Here, in particular, conjugated polymers are favored for flexible electronics due to their mechanical flexibility and potential for solution-processed fabrication techniques, such as blade-coating, roll-to-roll printing, and high-throughput printing allowing for high-performance transistor devices. Thiophene is the prevailing conjugated unit to construct these conjugated polymers due to its favorable electronic properties. On the other hand, furans are among the few conjugated moieties that are easily derived from bio renewable resources. To promote sustainability, we selectively introduced furan into the conjugated backbone of a high-mobility polymer scaffold and systematically studied the effect on the microstructure and charge transport. We show that partially and selectively replacing thiophene units with furan can yield nearly comparable performance compared to the all-thiophene polymer. This strategy offers an improvement in the sustainability of the polymer by incorporating bio-sourced furan without sacrificing the high-performance characteristics. Meanwhile, polymers with incorrect or complete furan incorporation show reduced mobilities. This work serves to develop coherent structure–morphology–performance relationships; such knowledge will establish guidelines for the future development of sustainable, furan-based conjugated materials.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Exceptional Alignment in a Donor–Acceptor Conjugated Polymer via a Previously Unobserved Liquid Crystal Mesophase

Abstract Orienting polymer semiconductors is desirable to optimize device characteristics, provide insight into microstructure, and magnify subtle phase behavior. Here, a combination of uniaxial strain and subsequent heating of the donor–acceptor (DA) polymer PBnDT‐FTAZ is discovered to lead to exceptional optical dichroic ratios of up to 38 (and close to 50 near the polymer's absorption edge). This alignment is achieved due to the existence of a previously undetected thermotropic liquid crystal (LC) mesophase. The LC transition, not discernable through calorimetry, is uncovered through a combination of in situ UV–vis spectroscopy, X‐ray scattering, and dynamic mechanical analysis (DMA). Comparing PBnDT‐FTAZ to the non‐fluorinated PBnDT‐HTAZ and the homo polymer PBnDT, all of which show similar thermal transitions, reveals that exceptional alignment is only found in PBnDT‐FTAZ. This is attributed to the PBnDT‐FTAZ film having two distinct liquid crystal populations, and the polymer templating to a highly aligned, high‐clearing temperature population when heated. The DMA thermal relaxation behavior observed here is also seen in other DA conjugated polymers suggesting that such thermotropic LC mesophases may be common in these materials. These findings demonstrate a polymer semiconductor with remarkable alignment and uncover phase behavior with broad implications for process‐structure‐property relationships in polymer semiconductors.

36 MATERIALS SCIENCE↗
DOE OSTI2024

The role of interfacial donor–acceptor percolation in efficient and stable all-polymer solar cells

Polymerization of Y6-type acceptor molecules leads to bulk-heterojunction organic solar cells with both high power-conversion efficiency and device stability, but the underlying mechanism remains unclear. Here we show that the exciton recombination dynamics of polymerized Y6-type acceptors (Y6-PAs) strongly depends on the degree of aggregation. While the fast exciton recombination rate in aggregated Y6-PA competes with electron-hole separation at the donor–acceptor (D–A) interface, the much-suppressed exciton recombination rate in dispersed Y6-PA is sufficient to allow efficient free charge generation. Indeed, our experimental results and theoretical simulations reveal that Y6-PAs have larger miscibility with the donor polymer than Y6-type small molecular acceptors, leading to D–A percolation that effectively prevents the formation of Y6-PA aggregates at the interface. Besides enabling high charge generation efficiency, the interfacial D–A percolation also improves the thermodynamic stability of the blend morphology, as evident by the reduced device “burn-in” loss upon solar illumination.

14 SOLAR ENERGY↗
DOE OSTI2023

Precise synthesis and photovoltaic properties of giant molecule acceptors

Series of giant molecule acceptors DY, TY and QY with two, three and four small molecule acceptor subunits are synthesized by a stepwise synthetic method and used for systematically investigating the influence of subunit numbers on the structure-property relationship from small molecule acceptor YDT to giant molecule acceptors and to polymerized small molecule acceptor PY-IT. Among these acceptors-based devices, the TY-based film shows proper donor/acceptor phase separation, higher charge transfer state yield and longer charge transfer state lifetime. Combining with the highest electron mobility, more efficient exciton dissociation and lower charge carrier recombination properties, the TY-based device exhibits the highest power conversion efficiency of 16.32%. These results indicate that the subunit number in these acceptors has significant influence on their photovoltaic properties. This stepwise synthetic method of giant molecule acceptors will be beneficial to diversify their structures and promote their applications in high-efficiency and stable organic solar cells.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Auxiliary sequential deposition enables 19%-efficiency organic solar cells processed from halogen-free solvents

High-efficiency organic solar cells are often achieved using toxic halogenated solvents and additives that are constrained in organic solar cells industry. Therefore, it is important to develop materials or processing methods that enabled highly efficient organic solar cells processed by halogen free solvents. In this paper, we report an innovative processing method named auxiliary sequential deposition that enables 19%-efficiency organic solar cells processed by halogen free solvents. Our auxiliary sequential deposition method is different from the conventional blend casting or sequential deposition methods in that it involves an additional casting of dithieno[3,2-b:2’,3’-d]thiophene between the sequential depositions of the donor (D18-Cl) and acceptor (L8-BO) layers. The auxiliary sequential deposition method enables dramatic performance enhancement from 15% to over 18% compared to the blend casting and sequential deposition methods. Furthermore, by incorporating a branched-chain-engineered acceptor called L8-BO-X, device performance can be boosted to over 19% due to increased intermolecular packing, representing top-tier values for green-solvent processed organic solar cells. Comprehensive morphological and time-resolved characterizations reveal that the superior blend morphology achieved through the auxiliary sequential deposition method promotes charge generation while simultaneously suppressing charge recombination. This research underscores the potential of the auxiliary sequential deposition method for fabricating highly efficient organic solar cells using environmentally friendly solvents.

14 SOLAR ENERGY↗
DOE OSTI2023

Introducing a Phenyl End Group in the Inner Side Chains of A‐DA'D‐A Acceptors Enables High‐Efficiency Organic Solar Cells Processed with Nonhalogenated Solvent

Abstract Power conversion efficiency (PCE) of organic solar cells (OSCs) processed by nonhalogenated solvents is unsatisfactory due to the unfavorable morphology. Herein, two new small molecule acceptors (SMAs) Y6‐Ph and L8‐Ph are synthesized by introducing a phenyl end group in the inner side chains of the SMAs of Y6 and L8‐BO, respectively, for overcoming the excessive aggregation of SMAs in the long‐time film forming processed by nonhalogenated solvents. First, the effect of the film forming time on the aggregation property and photovoltaic performance of Y6, L8‐BO, Y6‐Ph, and L8‐Ph is studied by using the commonly used solvents: chloroform (CF) (rapid film forming process) and chlorobenzene (CB) (slow film forming process). It is found that Y6‐ and L8‐BO‐based OSCs exhibit a dramatic drop in PCE from CF‐ to CB‐processed devices owing to the large phase separation, while the Y6‐Ph and L8‐Ph based OSCs show obviously increased PCEs Furthermore, L8‐Ph‐based OSCs processed by nonhalogenated solvento‐xylene (o‐XY) achieved a high PCE of 18.40% with an FF of 80.11%. The results indicate that introducing a phenyl end group in the inner side chains is an effective strategy to modulate the morphology and improve the photovoltaic performance of the OSCs processed by nonhalogenated solvents.

Chemistry↗
DOE OSTI2023

Interactions between nonfullerene acceptors lead to unstable ternary organic photovoltaic cells

For organic photovoltaic (OPV) devices to achieve consistent performance and long operational lifetimes, organic semiconductors must be processed with precise control over their purity, composition, and structure. This is particularly important for high volume solar cell manufacturing where control of materials quality has a direct impact on yield and cost. Ternary-blend OPVs containing two acceptor–donor–acceptor (A–D–A)-type nonfullerene acceptors (NFAs) and a donor have proven to be an effective strategy to improve solar spectral coverage and reduce energy losses beyond that of binary-blend OPVs. Here, we show that the purity of such a ternary is compromised during blending to form a homogeneously mixed bulk heterojunction thin film. We find that the impurities originate from end-capping C=C/C=C exchange reactions of A–D–A-type NFAs, and that their presence influences both device reproducibility and long-term reliability. The end-capping exchange results in generation of up to four impurity constituents with strong dipolar character that interfere with the photoinduced charge transfer process, leading to reduced charge generation efficiency, morphological instabilities, and an increased vulnerability to photodegradation. As a consequence, the OPV efficiency falls to less than 65% of its initial value within 265 h when exposed to up to 10 suns intensity illumination. We propose potential molecular design strategies critical to enhancing the reproducibility as well as reliability of ternary OPVs by avoiding end-capping reactions.

14 SOLAR ENERGY↗
DOE OSTI2023

Control of Host-Matrix Morphology Enables Efficient Deep-Blue Organic Light-Emitting Devices

Mixing a sterically bulky, electron-transporting host material into a conventional single host–guest emissive layer is demonstrated to suppress phase separation of the host matrix while increasing the efficiency and operational lifetime of deep-blue phosphorescent organic light-emitting diodes (PHOLEDs) with chromaticity coordinates of (0.14, 0.15). Here, the bulky host enables homogenous mixing of the molecules comprising the emissive layer while suppressing single host aggregation; a significant loss channel of nonradiative recombination. By controlling the amorphous phase of the host-matrix morphology, the mixed-host device achieves a significant reduction in nonradiative exciton decay, resulting in 120 ± 6% increase in external quantum efficiency relative to an analogous, single-host device. In contrast to single host PHOLEDs where electrons are transported by the host and holes by the dopants, both charge carriers are conducted by the mixed host, reducing the probability of exciton annihilation, thereby doubling of the deep-blue PHOLED operational lifetime. These findings demonstrate that the host matrix morphology affects almost every aspect of PHOLED performance.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Characterizing and Improving the Thermal Stability of Organic Photovoltaics Based on Halogen-Rich Non-Fullerene Acceptors

In this work, the thermal stability of inverted, halogen-rich non-fullerene acceptor (NFA)-based organic photovoltaics (OPVs) with MoO x as the hole transporting layer is studied at temperatures up to 80°C. Over time, the power conversion efficiency shows a “check-mark” shaped thermal aging pattern, featuring an early decrease, followed by a long-term recovery. A high Cl concentration at the BHJ/MoO x interface in the thermally aged device is found using energy dispersive X-ray spectroscopy. X-Ray photoelectron spectroscopy shows that the MoO x is chlorinated after thermal aging. With bulk quantum efficiency analysis, we propose an explanation to the check-mark shaped pattern. Inserting a thin C 70 layer between the BHJ and MoO x suppresses the thermal degradation mechanisms, resulting in 3 orders of magnitude increase in device lifetime at 80°C.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Non-fullerene acceptor organic photovoltaics with intrinsic operational lifetimes over 30 years

Abstract Organic photovoltaic cells (OPVs) have the potential of becoming a productive renewable energy technology if the requirements of low cost, high efficiency and prolonged lifetime are simultaneously fulfilled. So far, the remaining unfulfilled promise of this technology is its inadequate operational lifetime. Here, we demonstrate that the instability of NFA solar cells arises primarily from chemical changes at organic/inorganic interfaces bounding the bulk heterojunction active region. Encapsulated devices stabilized by additional protective buffer layers as well as the integration of a simple solution processed ultraviolet filtering layer, maintain 94% of their initial efficiency under simulated, 1 sun intensity, AM1.5 G irradiation for 1900 hours at 55 °C. Accelerated aging is also induced by exposure of light illumination intensities up to 27 suns, and operation temperatures as high as 65 °C. An extrapolated intrinsic lifetime of > 5.6 × 10 4 h is obtained, which is equivalent to 30 years outdoor exposure.

14 SOLAR ENERGY↗
DOE OSTI2020

Fast Organic Vapor Phase Deposition of Thin Films in Light-Emitting Diodes

Fast deposition of thin films is essential for achieving low-cost, high throughput phosphorescent organic light emitting diode (PHOLED) production. In this work, we demonstrate rapid and uniform growth of semiconductor thin films by organic vapor phase deposition (OVPD). A green PHOLED comprising an emission layer (EML) grown at 50 Å/s with bis[2-(2-pyridinyl-N)phenyl-C](acetylacetonato)iridium(III) (Ir(ppy)2(acac)) doped into 4,4 bis(N-carbazolyl)-1,1zolylld (CBP) exhibits a maximum external quantum efficiency of 20 ± 1%. The morphology, charge transport properties, and radiative efficiency under optical and electrical excitation of the PHOLED EML are investigated as functions of the deposition rate via both experimental and theoretical approaches. The EML shows no evidence for gas phase nucleation of the organic molecules at deposition rates as high as 50 Å/s. However, the roll-off in quantum efficiency at high current progressively increases with deposition rate due to enhanced triplet-polaron annihilation. The roll-off results from accumulation of stress within the PHOLED EML that generates a high density of defect states. Here, the defects, in turn, act as recombination sites for triplets and hole polarons, leading to enhanced triplet-polaron annihilation at high current. We introduce a void nucleation model to describe the film morphology evolution that is observed using electron microscopy.

42 ENGINEERING↗