Engineering topics

Dinh, Long N.

Publications and source records attributed to Dinh, Long N..

3 records

DOE OSTI2022

Outgassing of casted and 3D printed silicones

Outgassing of 3D printed and casted silica-filled silicones was studied using a standard ASTM E-595 procedure and a modified Soreq’s method that allows very sensitive measurements of the outgassing kinetics even at low temperatures, 20 – 50 °C. We studied three different silica-filled silicones, non-porous cased M9787, and 3D printed LL50 and 40P materials. The present report shows that vacuum outgassing products of polysiloxane-based materials include multiple species. In addition to chemisorbed and physisorbed water outgassing, previously studied by TPD, polymer fragments of varying sizes evaporate as well. The chemical composition of the condensable volatile species collected on a Germanium substrate, was analyzed by FTIR. It was shown that all studied materials produce mostly PDMS-based outgassing products that form stable droplet-like structure on the Ge substrate. The highest amount of the condensable volatile species was measured for LL50. Isothermal TGA in nitrogen atmosphere of the LL50 material was compared to the standard vacuum outgassing. The results of TGA showed lower mass loss and higher water regain. The kinetics of the outgassing at relatively low temperatures of 20, 30 and 50 °C was studied using Thermoelectric Quartz Crystal Microbalance (TQCM). The TQCM surface was held at -10 °C to enhance condensation of the outgassed moisture. The analysis presented here, when combined with the extensive previous work on moisture outgassing, provides a better understanding of the aging mechanism of polysiloxane-based materials. In this work we show that outgassing techniques, usually applied for qualification of polymers for space-related applications, may be used as a complementary method to study thermal degradation and aging of silica-based silicones. Our results indicate that the long-term degradation mechanics and thermal degradation products depend primarily on the chemical composition of silicone-based material and only slightly affected by the manufacturing process. Surprisingly, the surface-to-volume ratio of the 3D printed vs. casted/molded materials showed only minor effect on the outgassing kinetic parameters.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Hydrogen Uptake Kinetics of 1,4-Bis(phenylethynyl)benzene Rubberized O-Rings: Measurements, Modeling, and Comparison with Additional Forms of Organic Getters

A class of molecules called “hydrogen getters” can react with, or scavenge, H 2 in applications where the hydrogen presence and/or buildup are not desirable. One such “getter”, 1,4-bis(phenylethynyl)benzene or DEB, can be incorporated into a silicone matrix in the form of an O-ring for added flexibility, environmental resiliency, and convenient use as a gasket in sealed applications. However, the performance and kinetics of this DEB-loaded rubberized O-ring have not yet been characterized. Here in this work, the hydrogen uptake kinetics of the rubberized DEB O-ring were extracted by the isoconversional analysis from isothermal isobaric data under conditions of 13,332 Pa H 2 and 305–325 K. The isoconversional and cylindrical diffusion approximations were then used to predict and model the hydrogen uptake of rubberized DEB O-rings under any arbitrary condition, as illustrated in this work for the simple case of a constant rate of hydrogen generation/input. In comparison with other Pd/carbon-based/organic getter systems, these rubberized DEB O-rings provide a type of hydrogen getter material with enhanced flexibility and catalyst protection in applications where an O-ring seal is needed.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Solid state NMR Investigation of Structural Differences in Pelletized DEB Samples

Upon hydrogenation of DEB pellets, which are composed of 75% virgin DEB and 25% of nanometer scale Pd catalysts on activated carbon, the uptake rate is strong, and the hydrogenation process is fast. However, the last batch of DEB pellets from KCNSC uptakes 10 times slower than traditional DEB pellets after ~ 50% consumption. In addition, the last batch of DEB getter pellets also became partially molten/wet during the hydrogenation process. This molten/wet phase during hydrogenation has only been observed with DPB and never with DEB formulation. DRIFT (diffuse reflection infrared Fourier transform) and XRD (x-ray diffraction) confirm that the questionable batch of DEB pellets from KCNSC are truly 100% DEB and not a mixture of DEB and DPB. So, there must be something different in the composition (like concentration and distribution of Pd) or interaction between the DEB molecules with the surrounding environment (activated carbon spreading medium). The possibility of some chemical contamination in the processing of this batch of questionable DEB getter pellets also comes to mind. Due to the ability of NMR to detect intermolecular interaction and sensitivity to small chemical concentration, NMR investigation was requested for this questionable batch of DEB getter pellets from KCNSC.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗