Engineering topics

Dlott, Dana D. (ORCID:0000000187197093)

Publications and source records attributed to Dlott, Dana D. (ORCID:0000000187197093).

3 records

DOE OSTI2022

Shock ignition and deflagration growth in plastic-bonded TATB (1, 3, 5-trinitro-2, 4, 6-triaminobenzene) microstructures

TATB (1,3,5-triamino-2,4,6-trinitrobenzene) plastic-bonded explosives (PBX) were shocked with laser-launched flyer plates. The spectral radiance of the emitted light from a small portion of the microstructure (a “microenvironment”) containing a small number of TATB particles with an estimated mass of 150 ng was measured every 0.8 ns from 1 ns to 200 μs and was analyzed to give radiance and time-dependent graybody temperatures. By fabricating an array with 186 PBX charges, we could obtain ≥15 shots at each of 12 velocities between 1.8 and 4.7 km/s. We found that every microenvironment generated a unique radiance fingerprint. Some of these microenvironments were much more reactive than average. The radiance has two peaks around 20 ns and 5 μs, associated with shock ignition and deflagration growth. In our interpretation, the shock creates an ensemble of hot spots of various sizes and temperatures. Of those hot spots that ignite, only a small portion, at about 2200 K, was large enough and hot enough to survive long enough (>100 ns) to ignite individual TATB particles, leading to deflagration. Integrating various time intervals of the radiance can quantify the strength of the shock–PBX interaction, and the decay and growth of the hot spot ensemble and the deflagration.

Akhtar, Meysam (ORCID:0000000243897837)↗

DOE OSTI2022

Comparing the shock sensitivity of insensitive energetic materials

We present a tabletop method to study the shock sensitivity of plastic-bonded explosives that are considered shock insensitive using high dynamic range optical emission spectroscopy with laser-launched km/s flyer plate impacts (2, 3, and 4 km/s), which measures the spectral radiance (the emission spectrum vs a calibrated intensity standard) every 0.8 ns in the nanosecond and microsecond regimes. The explosives were TATB (1,3,5 trinitro, 2,4,6 triamino benzene), FOX-7 (1,1-diamino-2,2-dinitroethylene), LLM-105 (2,6-diamino-3,5-dinitropyrazine-1-oxide), and NTO (nitrotriazolone), all with 20% Sylgard 182 binder. Time resolving emission from shocked explosives produces a unique fingerprint at each shock pressure, and the emission temporal profile can be used to understand each material's shock response and the underlying mechanisms within the framework of the well-known shock ignition and growth models. Ignition was characterized by the emission intensity during nanosecond hot spot ignition. The growth process, which occurs after the shock has unloaded, was characterized by the time derivative of microsecond emission intensity. Singular-value decomposition was used to determine a characteristic spectral radiance over the entire time range, and this radiance was fit to a graybody model to determine a characteristic temperature Tc. Even though these insensitive explosives have similar shock sensitivities, our method can clearly distinguish their shock response. FOX-7 and NTO were the most sensitive, with FOX-7 having the greatest shock ignition sensitivity, growth rate, and Tc. LLM-105 was much less sensitive than FOX-7 and NTO, and TATB consistently showed the lowest sensitivity by any measure.

Akhtar, Meysam (ORCID:0000000243897837)↗

DOE OSTI2021

Laser-driven flyer plate impact: Computational studies guided by experiments

We present a computational approach using a multimaterial, arbitrary Lagrangian–Eulerian code termed ALE3D to model the nanosecond/micrometer dynamics of the launch of 0.5–4.5 km/s laser-driven metal flyer plates and the impact with stationary targets of Pyrex and fused silica glasses, and Lexan and Plexiglas polymers, producing pressures in the target in the range of 5–20 GPa. The simulations are compared to experimental results where the flyer velocity profile and the velocity profile imparted to the target material were measured with high-speed velocimetry. The experimental flyer launch by a high-intensity pulsed laser is modeled by depositing heat into a thin vaporizable layer under the flyer plate. This model produces a flyer plate that has not been exposed to the laser pulse, allowing us to compare the properties of the real flyer to a simulated ideal flyer. The simulations of target impact are generally in good agreement with the experiment except at the highest impact velocities where the shock release process in the experiment is slower than that in the simulation. The cause of this disagreement is attributed to an inadequate description of the shock viscosity during the nanosecond unloading process.

Stekovic, Svjetlana (ORCID:0000000163878070)↗