Engineering topics

Doan, David

Publications and source records attributed to Doan, David.

6 records

DOE OSTI2024

High absorptivity nanotextured powders for additive manufacturing

The widespread application of metal additive manufacturing (AM) is limited by the ability to control the complex interactions between the energy source and the feedstock material. Here, we develop a generalizable process to introduce nanoscale grooves to the surface of metal powders which increases the powder absorptivity by up to 70% during laser powder bed fusion. Absorptivity enhancements in copper, copper-silver, and tungsten enable energy-efficient manufacturing, with printing of pure copper at relative densities up to 92% using laser energy densities as low as 83 joules per cubic millimeter. Simulations show that the enhanced powder absorptivity results from plasmon-enabled light concentration in nanoscale grooves combined with multiple scattering events. The approach taken here demonstrates a general method to enhance the absorptivity and printability of reflective and refractory metal powders by changing the surface morphology of the feedstock without altering its composition.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Direct Observation of the Pressure-Induced Structural Variation in Gold Nanoclusters and the Correlated Optical Response

The ability to gradually modify the atomic structures of nanomaterials and directly identify such structural variation is important in nanoscience research. Here, we present the first example of a high-pressure single-crystal X-ray diffraction analysis of atomically precise metal nanoclusters. The pressure-dependent, subangstrom structural evolution of an ultrasmall gold nanoparticle, Au 25 S 18 , has been directly identified. We found that a 0.1 Å decrease of the Au–Au bond length could induce a blue-shift of 30 nm in the photoluminescence spectra of gold nanoclusters. From theoretical calculations, the origins of the blue-shift and enhanced photoluminescence under pressure are investigated, which are ascribed to molecular orbital symmetry and conformational locking, respectively. Here, the combination of the high-pressure in situ X-ray results with both theoretical and experimental optical spectra provides a direct and generalizable avenue to unveil the underlying structure–property relations for nanoclusters and nanoparticles which cannot be obtained through traditional physical chemistry measurements.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2022

Nanoparticle-enhanced absorptivity of copper during laser powder bed fusion

We report laser powder bed fusion (LPBF) of pure copper for thermal and electrical applications is hampered by its low near-infrared absorptivity and high thermal diffusivity. These material properties make it very difficult to localize the thermal energy needed to produce high density 3D printed parts. Modification of metal powders via nanoparticle additives is a promising approach to increasing absorptivity, but the effect of nanoparticles on absorptivity and melting behavior during LPBF is not well understood. In this study, we developed an in situ calorimetry system to measure effective absorptivity during LPBF on copper substrates. We decorated copper substrates using three nanoparticle systems (CuS, TiB 2 , multilayer graphene flakes) and demonstrated an enhanced absorptivity of the decorated substrates relative to pure copper. Graphene nanoflakes resulted in the highest improved absorption relative to pure copper from 0.09 to 0.48, due to their stability at high laser scanning powers. A thermomechanical model with convective heat transfer provided confidence in the measurements by reproducing the experimental melt pool traces. Full 3D cylindrical prints demonstrated an improvement in relative density of the copper-graphene powder prints (in the range of 0.930–0.992), relative to that of as-purchased copper powder prints (in the range of 0.854–0.972). This work provides a fundamental study of nanoparticle-enabled LPBF of highly reflective metals and demonstrates a viable route for expanding the library of reliably printable metals.

36 MATERIALS SCIENCE↗

DOE OSTI2020

Stress-Induced Structural Transformations in Au Nanocrystals

Nanocrystals can exist in multiply twinned structures like icosahedron or single crystalline structures like cuboctahedron. Transformations between these structures can proceed through diffusion or displacive motion. Experimental studies on nanocrystal structural transformations have focused on high-temperature diffusion-mediated processes. Limited experimental evidence of displacive motion exists. We report structural transformation of 6 nm Au nanocrystals under nonhydrostatic pressure of 7.7 GPa in a diamond anvil cell that is driven by displacive motion. X-ray diffraction and transmission electron microscopy were used to detect the structural transformation from multiply twinned to single crystalline. Single crystalline nanocrystals were recovered after unloading, then quickly reverted to the multiply twinned state after dispersion in toluene. Furthermore, the dynamics of recovery was captured using TEM which showed surface recrystallization and rapid twin boundary motion. Molecular dynamics simulations showed that twin boundaries are unstable due to defects nucleated from the interior of the nanocrystal.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

DOE OSTI2020

Hardening in Au-Ag nanoboxes from stacking fault-dislocation interactions

Porous, nano-architected metals with dimensions down to ~10 nm are predicted to have extraordinarily high strength and stiffness per weight, but have been challenging to fabricate and test experimentally. Here, we use colloidal synthesis to make ~140 nm length and ~15 nm wall thickness hollow Au-Ag nanoboxes with smooth and rough surfaces. In situ scanning electron microscope and transmission electron microscope testing of the smooth and rough nanoboxes show them to yield at 130 ± 45 MPa and 96 ± 31 MPa respectively, with significant strain hardening. A higher strain hardening rate is seen in rough nanoboxes than smooth nanoboxes. Finite element modeling is used to show that the structure of the nanoboxes is not responsible for the hardening behavior suggesting that material mechanisms are the source of observed hardening. Molecular dynamics simulations indicate that hardening is a result of interactions between dislocations and the associated increase in dislocation density.

42 ENGINEERING↗

DOE OSTI2020

Nucleation of Dislocations in 3.9 nm Nanocrystals at High Pressure

As circuitry approaches single nanometer length scales, it has become important to predict the stability of single nanometer-sized metals. The behavior of metals at larger scales can be predicted based on the behavior of dislocations, but it is unclear if dislocations can form and be sustained at single nanometer dimensions. Here, we report the formation of dislocations within individual 3.9 nm Au nanocrystals under nonhydrostatic pressure in a diamond anvil cell. We used a combination of x-ray diffraction, optical absorbance spectroscopy, and molecular dynamics simulation to characterize the defects that are formed, which were found to be surface-nucleated partial dislocations. These results indicate that dislocations are still active at single nanometer length scales and can lead to permanent plasticity.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗