Engineering topics

Dodd, Evan S.

Publications and source records attributed to Dodd, Evan S..

4 records

DOE OSTI2023

Roadmap for the exposé of radiation flows (Xflows) experiment on $\mathrm{NIF}$

Here, the goal of the Xflows experimental campaign is to study the radiation flow on the National Ignition Facility (NIF) reproducing the sensitivity of the temperature (±8 eV, ±23 μm) and density (±11 mg/cc) measurements of the COAX platform. This new platform will enable future astrophysical experiments involving supernova shock breakout, such as Radishock on OMEGA-60, and stochastic media (such as XFOL on OMEGA). Greater energy and larger physical scale on NIF will enable a greater travel distance of radiation flow, higher density, and more manufacturable foams and enable exploration of a greater range of radiation behavior than achievable in the prior OMEGA experiments. This publication will describe the baseline configuration for the Xflows experimental campaign and the roadmap to achieve its primary objectives.

47 OTHER INSTRUMENTATION↗

DOE OSTI2022

Density measurements for the National Ignition Facility (NIF) opacity platform

The Opacity Platform on the National Ignition Facility (NIF) has been developed to measure opacities at varying densities and temperatures relevant to the solar interior and thermal cooling rates in white dwarf stars. The typical temperatures reached at NIF range between 150 and 210 eV, which allow these measurements to be performed experimentally. The captured opacities are crucial to validating radiation-hydrodynamic models that are used in astrophysics. The NIF opacity platform has a unique new capability that allows in situ measurement of the sample expansion. The sample expansion data are used to better understand the plasma conditions in our experiments by inferring the sample density throughout the duration of the laser drive. Here, we present the details of the density measurement technique, data analysis, and recent results for Fe and MgO.

47 OTHER INSTRUMENTATION↗

DOE OSTI2022

Fast ignition inertial fusion energy using laser-driven ion beams

Ion fast ignition (IFI), or fusion fast ignition initiated by a laser-driven ion beam, is a promising path to high-gain inertial fusion energy (IFE). In IFI, cold, dense deuterium-tritium (DT) fuel is first assembled using lasers or pulsed power drivers. Then, a high-power ion beam is focused onto a small volume within the fuel (the hot spot), heating the fuel rapidly to conditions where fusion ignition takes place. Fusion burn in this hot spot propagates to the fuel surrounding the hot spot, leading to burnup of a significant fraction of this fuel and the possibility of high gain (G~100), as needed for inertial fusion energy. IFI uses separate drivers for the two basic elements, fuel compression and ignition, allowing maximum control and optimization of each. On the other hand, conventional laser fusion uses multiple beams of the same driver to compress the fuel and shock-heat its very center to ignite a burn wave. Despite impressive progress in conventional laser fusion, the precise spatial symmetry, temporal pulse shaping and timing required for high gain and IFE remain a serious unmet challenge.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗

DOE OSTI2020

Opacity on NIF: Anchor 2 Iron (Level 2 Milestone 7118 Report)

In FY2020 we fulfilled the exit criteria of milestone 7118. We fielded iron opacity experiments at higher densities and temperatures approaching anchor 2 conditions and made good progress on overcoming the problems that we found. This report describes in detail the progress that has been made. We presented the results in a LANL seminar on August 10 and we gave two talks on our results to the National Opacity Workshop Series, one on July 9 and the other on September 14. Before discussing the anchor 2 measurements, we present an update of the NIF anchor 1 data. We did a new analysis of the anchor 1 data and compared the results to a series of calculations using the LANL ATOMIC code. Figures 1 and 2 compare the data with the best-fit to calculations. This result is significantly improved over the result published in Atoms. The differences are small for the iron quasi-continuum between 8-9.5 Å and for the Mg Heα and Lyα lines. The opacities near the centers of the iron bound-bound features also match fairly well in the 9.5-12.5 Å range. However, the opacity windows between the large iron bound-bound features are deeper in the Atomic predictions than the measurement. Furthermore, large discrepancies exist for the Mg He β, γ, and δ lines and for the short-wavelength quasicontinuum. The experiment and analysis refinements described below have set the stage for unraveling these discrepancies. Specifically, we can repeat the Anchor 1 experiments using improved backlighter, hohlraum, and spectrometers to obtain reduced backgrounds and better spectral resolution. Exploiting the AlMg calibration experiments and repeating the Anchor 1 measurements multiple times will enable formal and rigorous uncertainty determination. This well-defined path gives us confidence that high quality opacity data can be obtained on NIF.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗