Engineering topics
Publications and source records attributed to Dolling, David S..
The focus was on developing means of controlling and reducing unsteady pressure loads in separated shock wave turbulent boundary layer interactions. Section 1 describes how vortex generators can be used to effectively reduce loads in compression ramp interaction, while Section 2 focuses on the effects of 'boundary-layer separators' on the same interaction.
Fluctuating wall pressure measurements have been made in a separated shock wave/turbulent boundary layer interaction produced by an unswept compression corner in a Mach 5 flow. Wheeler doublet vortex generators were placed 15.8 boundary layer thicknesses upstream of the corner to study their effect on the fluctuating pressure loads produced by the translating separation shock. The vortex generators produced significant three-dimensionality in an otherwise two-dimensional interaction. They reduced the upstream influence and the length of the region of shock motion by 60% and 64%, respectively, decreased the maximum wall pressure rms by 23%, and shifted the fluctuations to a higher frequency band. The maximum fraction of energy in the 100-500 Hz frequency band is decreased by 11%. These changes are due to a fuller boundary layer profile, a weaker separation shock, and increased boundary layer turbulence causing increased separation shock jitter.
Fluctuating surface pressure measurements have been made to investigate the effectiveness of boundary layer separators (BLS's) in reducing the fluctuating pressure loads produced by separated shock wave turbulent boundary layer interactions. Measurements have been made under unswept and swept compression corner interactions in a Mach 5 flow. BLS's fix the separation location and eliminate the large-amplitude, low-frequency fluctuating pressure loads upstream of the compression corners. The loads on the unswept compression corner face are reduced by as much as 59%. The BLS's also shift the mean pressure distribution on the unswept corner face in the streamwise direction. Results show that the loads on the corner face vary with the BLS height and the distance between the BLS and the compression corner. Suggestions for the optimum placement and the use of the BLS's are also made.
Fluctuating wall pressure measurements have been made on centerline upstream of a blunt fin in a Mach 5 turbulent boundary layer. By examining the ensemble averaged wall pressure distributions for different separation shock foot positions, it has been shown that local fluctuating wall pressure measurements are due to a distinct pressure distribution, Rho(sub i), which undergoes a stretching and flattening effect as its upstream boundary translates aperiodically between the upstream influence and separation lines. The locations of the maxima and minima in the wall pressure standard deviation can be accurately predicted using this distribution, providing quantitative confirmation of the model. This model also explains the observed cross-correlations and ensemble average measurements within the interaction. Using the Rho(sub i) model, wall pressure signals from under the separated flow region were used to reproduce the position-time history of the separation shock foot. Further, the negative time delay peak in the cross-correlation between the predicted and actual shock foot histories suggests that the separated region fluctuations precede shock foot motion. The unsteady behavior of the primary horseshoe vortex and its relation to the unsteady separation shock are described.
Over the period of this grant (1986-92), 23 graduate students were supported by the Center and received education and training in hypersonics through MS and Ph.D. programs. An additional 8 Ph.D. candidates and 2 MS candidates, with their own fellowship support, were attracted to The University of Texas and were recruited into the hypersonics program because of the Center. Their research, supervised by the 10 faculty involved in the Center, resulted in approximately 50 publications and presentations in journals and at national and international technical conferences. To provide broad-based training, a new hypersonics curriculum was created, enabling students to take 8 core classes in theoretical, computational, and experimental hypersonics, and other option classes over a two to four semester period. The Center also developed an active continuing education program. The Hypersonics Short Course was taught 3 times, twice in the USA and once in Europe. Approximately 300 persons were attracted to hear lectures by more than 25 of the leading experts in the field. In addition, a hypersonic aerodynamics short course was offered through AIAA, as well as short courses on computational fluid dynamics (CFD) and advanced CFD. The existence of the Center also enabled faculty to leverage a substantial volume of additional funds from other agencies, for research and graduate student training. Overall, this was a highly successful and highly visible program.
A computational study has been performed of sharp fin-induced swept shock wave/turbulent boundary layer interactions at low hypersonic Mach numbers. The objective was to determine if results obtained using a conical Navier-Stokes code, particularly the peak heating and pressure, are adequate for engineering predictions. The advantage of the conical approach is that the problem becomes two-dimensional and requires much less computational effort than a fully three-dimensional calculation. In this code, the standard Baldwin-Lomax model is used for turbulent closure and its performance is studied in some detail. To assess the approach interactive flowfields generated by unswept sharp fins at two angles of attack at each of three hyprsonic freestream Mach numbers (5, 6, 11) have been calculated and the results compared with experimental wall pressure and heat transfer data. Although the conical Navier-Stokes/Baldwin-Lomax approach is reasonably successful at Mach numbers up to 5, the performance deteriorates as the Mach number is increased. Nevertheless, the approach could be a valuable tool in preliminary parametric design studies.
Explore the source record for details and available documents.
A combined experimental/computational study has been performed of sharp fin induced shock wave/turbulent boundary layer interactions at Mach 5. The current paper focuses on the experiments and analysis of the results. The experimental data include mean surface heat transfer, mean surface pressure distributions and surface flow visualization for fin angles of attack of 6, 8, 10, 12, 14 and 16-degrees at Mach 5 under a moderately cooled wall condition. Comparisons between the results and correlations developed earlier show that Scuderi's correlation for the upstream influence angle (recast in a conical form) is superior to other such correlations in predicting the current results, that normal Mach number based correlations for peak pressure heat transfer are adequate and that the initial heat transfer peak can be predicted using pressure-interaction theory.
Wall pressure fluctuations have been measured under the unsteady separation shock and on the ramp face in an unswept Mach 5 compression ramp interaction. The freestream Reynolds number was 51.0 x 10 to the 6th/m, and the incoming turbulent boundary layer developed on the tunnel floor under approximately adiabatic wall temperature conditions. Standard data-acquisition methods, as well as real-time and posttest conditional sampling techniques were used. The results show that the mean and rms pressure levels are strong functions of separation shock position. At all stations on the ramp, from the corner to where the pressure reaches the theoretical inviscid value, the pressure signals have two dominant components: a low frequency component characteristic of the global unsteadiness, which correlates with the separation shock motion, and a higher frequency component associated with turbulence. The former is the major contributor to the overall signal variance.