Engineering topics

Doran, D.

Publications and source records attributed to Doran, D..

4 records

NASA NTRS1996

Overview of CFD Analyses Supporting the Reusable Solid Rocket Motor (RSRM) Program at MSFC

During the past year, various computational fluid dynamic (CFD) analyses were performed at Marshall Space Flight Center to support the Reusable Solid Rocket Motor program. The successful completion of these analyses involved application of the CFD codes FDNS and CELMINT. The topics addressed by the analyses were: (1) the design and prediction of slag pool accumulation within the five inch test motor, (2) prediction of slag pool behavior and its response to lateral accelerations, (3) the clogging of potential insulation debonds within the nozzle by slag accumulation, (4) the behavior of jets within small voids inside nozzle joint gaps, (5) The effect of increased inhibitor stiffness on motor acoustics, and (6) the effect of a nozzle defect on particle impingement enhanced erosion. The emphasis of this presentation will be to further discuss the work in topics 3, 4, and 5.

Stewart, Eric↗

NASA NTRS1996

Numerical Investigation of Slag Behavior for RSRM

It is known that the flow field of the redesigned solid rocket motor (RSRM) is very complicated due to the complex characteristics of turbulent multi-phase flow, chemical reaction, particle combustion, evaporation, breakup and agglomeration etc. It requires multi-phase calculations, chemical reaction simulation, and particle combustion, evaporation, and breakup models to obtain a better understanding of thermophysics for the RSRM design using numerical methods. Also, the slag buildup due to the molten particles is another factor affecting the performance of the RSRM. To achieve this goal, the volume of fluid (VOF) method is used to capture the free surface motion so as to simulate the accumulation of the molten particles (slag) of the RSRM. A finite rate chemistry model is used to simulate the chemical reaction effects. For multi-phase calculations, the Hermsen combustion model is used for the aluminum particle combustion analysis and the Taylor Analogy Breakup (TAB) model is used for the particle breakup analysis. An interphase mas-exchange model introduced by Spalding is used for the evaporation calculation. The particle trajectories are calculated using a one-step implicit method for several groups of particle sizes by which the drag forces and heat fluxes are then coupled with the gas phase equations. The preliminary results predicted a reasonable physical simulation of the particle effects using a simple two dimensional solid rocket motor configuration. It shows that the AL/AL2O3 particle sizes are reduced due to the combustion, evaporation, and breakup. The flow field is disturbed by the particles. Mach number distributions in the nozzle are deformed due to the effect of particle concentrations away from the center line.

Liaw, P.↗

NASA NTRS1989

Conjugate (solid/fluid) computational fluid dynamics analysis of the space shuttle solid rocket motor nozzle/case and case field joints

Three-dimensional, conjugate (solid/fluid) heat transfer analyses of new designs of the Solid Rocket Motor (SRM) nozzle/case and case field joints are described. The main focus was to predict the consequences of multiple rips (or debonds) in the ambient cure adhesive packed between the nozzle/case joint surfaces and the bond line between the mating field joint surfaces. The models calculate the transient temperature responses of the various materials neighboring postulated flow/leakpaths into, past, and out from the nozzle/case primary O-ring cavity and case field capture O-ring cavity. These results were used to assess if the design was failsafe (i.e., no potential O-ring erosion) and reusable (i.e., no excessive steel temperatures). The models are adaptions and extensions of the general purpose PHOENICS fluid dynamics code. A non-orthogonal coordinate system was employed and 11,592 control cells for the nozzle/case and 20,088 for the case field joints are used with non-uniform distribution. Physical properties of both fluid and solids are temperature dependent. A number of parametric studies were run for both joints with results showing temperature limits for reuse for the steel case on the nozzle joint being exceeded while the steel case temperatures for the field joint were not. O-ring temperatures for the nozzle joint predicted erosion while for the field joint they did not.

Doran, D.↗

NASA NTRS1967

Simple colorimetric method determines uranium in tissue

Simple colorimetric micromethod determines concentrations of uranium in tissue. The method involves dry ashing organic extraction, and colorimetric determination of uranyl ferrocyanide. This uranium determination technique could be used in agricultural research, tracer studies, testing of food products, or medical research.

Doran, D.↗