Search NASA⌕ Search

Engineering topics

Dravid, Vinayak P.

Publications and source records attributed to Dravid, Vinayak P..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2025

Steam-Assisted Ammonolysis of MoO2 as a Synthetic Pathway to Oxygenated δ-MoN

A common route for the synthesis of molybdenum nitrides is through the temperature-programmed reaction of molybdenum oxides with NH3, or ammonolysis. In this work, the role of precursor phase, gas phase chemistry (impact of H2O), and temperature profile on the reaction outcome (700 °C) was examined, which resulted in varying amounts of MoO2, H2MoO5, and the nitride phases—cubic γ (nominally Mo2N) and hexagonal δ (nominally MoN). The phase fraction of the δ phase increased with precursor in the sequence MoO2 > MoO3 > H2MoO5. Steam in the reaction gas also favored the production of δ over γ, but with too much steam, MoO2 was obtained in the product. Synthesis conditions for obtaining nearly phase-pure δ were identified: MoO2 as the precursor, 2% H2O in the gas stream, and a moderate heating rate (3 °C/min). In situ X-ray diffraction provided insights into the reaction pathway. Extensive physico-chemical analysis of the δ phase, including synchrotron X-ray and neutron diffraction, electron microscopy, thermogravimetric analysis, X-ray photoelectron spectroscopy, and prompt gamma activation analysis, revealed its stoichiometry to be MoO0.108(8)N0.892(8)H0.012(5), indicating non-trivial oxygen incorporation. The presence of N/O ordering and an impurity phase Mo5N6 were also revealed, detectable only by neutron diffraction. Notably, a computationally predicted MoON phase (doi: 10.1103/PhysRevLett.123.236402), of interest due to its potential to display a metal-insulator transition, did not appear under any reaction condition examined.

Pandey, Shobhit↗
DOE OSTI2024

Enhanced superconducting qubit performance through ammonium fluoride etch

The performance of superconducting qubits is often limited by dissipation and two-level systems (TLS) losses. The dominant sources of these losses are believed to originate from amorphous materials and defects at interfaces and surfaces, likely as a result of fabrication processes or ambient exposure. Here, we explore a novel wet chemical surface treatment at the Josephson junction-substrate and the substrate-air interfaces by replacing a buffered oxide etch (BOE) cleaning process with one that uses hydrofluoric acid followed by aqueous ammonium fluoride. We show that the ammonium fluoride etch process results in a statistically significant improvement in median $\text{T}_1$ by $\sim22\%$ (p = 0.002), and a reduction in the number of strongly-coupled TLS in the tunable frequency range. Microwave resonator measurements on samples treated with the ammonium fluoride etch after niobium deposition and etching also show $\sim33\%$ lower TLS-induced loss tangent compared to the BOE treated samples. As the chemical treatment primarily modifies the Josephson junction-substrate interface and substrate-air interface, we perform targeted chemical and structural characterizations to examine materials differences at these interfaces and identify multiple microscopic changes that could contribute to decreased TLS losses.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Unraveling the adsorption-limited hydrogen oxidation reaction at palladium surface via in situ electron microscopy

Palladium (Pd) catalysts have been extensively studied for the direct synthesis of H 2 O through the hydrogen oxidation reaction at ambient conditions. This heterogeneous catalytic reaction not only holds considerable practical significance but also serves as a classical model for investigating fundamental mechanisms, including adsorption and reactions between adsorbates. Nonetheless, the governing mechanisms and kinetics of its intermediate reaction stages under varying gas conditions remain elusive. This is attributed to the intricate interplay between adsorption, atomic diffusion, and concurrent phase transformation of catalyst. Herein, the Pd-catalyzed, water-forming hydrogen oxidation is studied in situ, to investigate intermediate reaction stages via gas cell transmission electron microscopy. The dynamic behaviors of water generation, associated with reversible palladium hydride formation, are captured in real time with a nanoscale spatial resolution. Our findings suggest that the hydrogen oxidation rate catalyzed by Pd is significantly affected by the sequence in which gases are introduced. Through direct evidence of electron diffraction and density functional theory calculation, we demonstrate that the hydrogen oxidation rate is limited by precursors’ adsorption. These nanoscale insights help identify the optimal reaction conditions for Pd-catalyzed hydrogen oxidation, which has substantial implications for water production technologies. The developed understanding also advocates a broader exploration of analogous mechanisms in other metal-catalyzed reactions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Material and Interface Engineering Strategies to Mitigate Decoherence in Superconducting Qubits

While significant strides have been made to increase the coherence time of superconducting qubits, further advancements are essential for realizing scalable quantum computing. Decoherence is often a result of loss and noise stemming from two-level systems and excess quasiparticles, arising due to material defects, fabrication processes, and ambient exposure, particularly at surfaces and interfaces. Our recent efforts to mitigate these decoherence mechanisms have employed a variety of strategies, including low-loss surface encapsulation materials, advanced substrate preparation techniques, modifications to metal film growth, and the development of novel fabrication processes. The structural and chemical properties of materials, surfaces, and interfaces are studied using scanning probe microscopy, electron microscopy, photoelectron spectroscopy, mass spectrometry, and X-ray diffraction, which is correlated to device performance metrics, including superconducting resonator internal quality factor and qubit T1 time. This information is used to identify and understand material sources of loss and their origins in the device fabrication process. Through multi-institution efforts within SQMS we have identified the loss mechanism of interstitial hydrogen in niobium-based devices and shown how standard fabrication processes introduce these hydrides, developing strategies to mitigate their formation.1 Furthermore, we have characterized the metal-substrate interface, including the loss of niobium-silicides formed at that interface, and developed silicon surface treatments that reduce atomic scale roughness and oxygen content at the metal-substrate and Josephson junction interfaces.2-4 By developing the connection between materials properties and the overall performance of superconducting quantum circuitry, we can develop fabrication strategies to mitigate material losses, thus supporting the ongoing efforts to enhance coherence time in superconducting quantum devices. 1. Torres-Castanedo, C. G.*, Goronzy, D. P.*, et al., Adv. Funct. Mater., 2401365 (2024) 2. Lu, X., et al., Phys. Rev. Materials 6, 064402 (2022) 3. Berti, G., Appl. Phys. Lett. 122, 192605 (2023) 4. Kopas, C. J., Goronzy, D. P., et al., arXiv:2408.02863 (2024)

Goronzy, Dominic P.↗
DOE OSTI2024

Identifying Spectral Descriptors for Protonation in BaZr 0.8 Y 0.2 O 3-x with Electron Energy Loss Spectroscopy

Hydrogen economy is of paramount importance in the global transition to a sustainable, clean energy source that contributes to decarbonization efforts. In particular, the proton conducting proton ceramic fuel cells (PCFCs) play a crucial role in promoting hydrogen energy technology [1-5]. In a PCFC, the electrolyte is typically a solid oxide material that enables proton transport and can operate at temperatures lower than those of traditional oxygen ion conducting fuel cells [6]. The reduced operating temperature of PCFCs contributes to their durability, scalability, and efficiency [7,8]. BaZr 0.8 Y 0.2 O 3-x (BZY) is a promising proton conducting solid oxide electrolyte [9,10]. The emphasis on proton conductivity entails the importance of understanding proton content in the system. However, previous studies have largely relied on bulk techniques such as electrochemical impedance spectroscopy [7,11], Karl-Fischer titration [12,13], and thermogravimetric analysis [14] to obtain proton concentration. This is due to the small atomic size and light mass of hydrogen species making direct detection challenging. Bulk methods may be useful in estimating the proton content; however, it overlooks possible proton concentration gradient or segregation that may occur across or within a nanoparticle, especially when proton incorporation occurs nonuniformly through steam exposure on powder samples. In this paper, BZY is protonated at an estimated 0.15 mol of protons via steam exposure. Electron energy loss spectroscopy (EELS) with nanoscale spatial resolution is explored to identify proxy signals for proton detection using a JEOL ARM300 microscope operated at 300 kV with a Gatan GIF Continuum detector.

08 HYDROGEN↗
DOE OSTI2024

Direct Probing of Radiolysis Chemistry in the Gas Cell Electron Microscopy

Here, the radiolytic decomposition of materials is inevitable in electron microscopy, alongside knock-on effects, electrical charging, and heating damage. Especially with the radiation-susceptible chemistry in the fluidic phase (liquid and gas), consideration of mitigating or leveraging these phenomena is particularly important.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2024

Formation and Microwave Losses of Hydrides in Superconducting Niobium Thin Films Resulting from Fluoride Chemical Processing

Abstract Superconducting niobium (Nb) thin films have recently attracted significant attention due to their utility for quantum information technologies. In the processing of Nb thin films, fluoride‐based chemical etchants are commonly used to remove surface oxides that are known to affect superconducting quantum devices adversely. However, these same etchants can also introduce hydrogen to form Nb hydrides, potentially negatively impacting microwave loss performance. Here, comprehensive materials characterization of Nb hydrides formed in Nb thin films as a function of fluoride chemical treatments is presented. In particular, secondary‐ion mass spectrometry, X‐ray scattering, and transmission electron microscopy reveal the spatial distribution and phase transformation of Nb hydrides. The rate of hydride formation is determined by the fluoride solution acidity and the etch rate of Nb 2 O 5, which acts as a diffusion barrier for hydrogen into Nb. The resulting Nb hydrides are detrimental to Nb superconducting properties and lead to increased power‐independent microwave loss in coplanar waveguide resonators. However, Nb hydrides do not correlate with two‐level system loss or device aging mechanisms. Overall, this work provides insight into the formation of Nb hydrides and their role in microwave loss, thus guiding ongoing efforts to maximize coherence time in superconducting quantum devices.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Discovering polyelemental nanostructures with redistributed plasmonic modes through combinatorial synthesis

Coupling plasmonic and functional materials provides a promising way to generate multifunctional structures. However, finding plasmonic nanomaterials and elucidating the roles of various geometric and dielectric configurations are tedious. This work describes a combinatorial approach to rapidly exploring and identifying plasmonic heteronanomaterials. Symmetry-broken noble/non-noble metal particle heterojunctions (~100 nanometers) were synthesized on multiwindow silicon chips with silicon nitride membranes. The metal types and the interface locations were controlled to establish a nanoparticle library, where the particle morphology and scattering color can be rapidly screened. By correlating structural data with near- and far-field single-particle spectroscopy data, we found that certain low-energy plasmonic modes could be supported across the heterointerface, while others are localized. Furthermore, we found a series of triangular heteronanoplates stabilized by epitaxial Moiré superlattices, which show strong plasmonic responses despite largely comprising a lossy metal (~70 atomic %). These architectures can become the basis for multifunctional and cost-effective plasmonic devices.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Ultrasmooth Epitaxial Pt Thin Films Grown by Pulsed Laser Deposition

Platinum (Pt) thin films are useful in applications requiring high-conductivity electrodes with excellent thermal and chemical stability. Ultrasmooth and epitaxial Pt thin films with single-crystalline domains have the added benefit of providing ideal templates for the subsequent growth of heteroepitaxial structures. Here, we grow epitaxial Pt (111) electrodes (ca. 30 nm thick) on sapphire (α-Al 2 O 3 (0001)) substrates with pulsed laser deposition. This versatile technique allows control of the growth process and fabrication of films with carefully tailored parameters. X-ray scattering, atomic-force microscopy, and electron microscopy provide structural characterization of the films. Various gaseous atmospheres and temperatures were explored to achieve epitaxial growth of films with low roughness. A two-step (500 °C/300 °C) growth process was developed, yielding films with improved epitaxy without compromising roughness. The resulting films possess ultrasmooth interfaces (<3 Å) and high electrical conductivity (6.9 × 10 6 S/m). Finally, Pt films were used as current collectors and templates to grow lithium manganese oxide (LiMn 2 O 4 (111)) epitaxial thin films, a cathode material used in Li-ion batteries. In conclusion, using a solid-state ionogel electrolyte, the films were highly stable when electrochemically cycled in the 3.5-4.3 V vs Li/Li + range.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Mapping the Complete Reaction Energy Landscape of a Metal–Organic Framework Phase Transformation

Crystalline materials undergo valuable phase transformations, and the energetic processes that underlie these transformations can be fully characterized through a combination of thermodynamic and kinetic studies. Here, we report the first complete reaction energy landscape of metal–organic framework (MOF) interpenetration, specifically in the phase transformation of NU-1200 to its doubly interpenetrated counterpart, STA-26. We characterized the thermodynamics of this phase transformation by pairing experiments with density functional theory (DFT) calculations. This analysis revealed that factors such as the increase in crystal density likely drive Zr- and Hf-NU-1200 to STA-26 interpenetration, while other chemical interactions such as steric repulsions prevent Th-NU-1200 from interpenetrating. Using time-resolved in situ X-ray diffraction, we monitored phase transformation reaction profiles and extracted quantitative kinetic information using the Avrami-Erofe’ev model. As a result, we obtained activation energies for the Zr- and Hf-NU-1200 transformations to Zr- and Hf-STA-26, respectively, revealing slower phase change kinetics for MOFs with stronger bonds. Finally, we paired the kinetic data with experimental observations to classify the mechanistic model of this phase transformation as partial dissolution. Here, we anticipate that this thermodynamic, kinetic, and mechanistic understanding will broadly inform further studies on the energetics of crystallization.

38 RADIATION CHEMISTRY, RADIOCHEMISTRY, AND NUCLEA↗
DOE OSTI2023

Beneficial Effects of La 0.5 Sr 0.5 CoO 3 Coatings on Thin‐Film LiMn 2 O 4 Cathodes for Lithium Ion Batteries

Abstract The severe capacity loss of spinel LiMn 2 O 4 (LMO) limits the utility of this otherwise promising lithium ion battery cathode material. One of the strategies to mitigate capacity fade is applying a coating on LMO particle surfaces. While this approach yields promising results, there is limited understanding of mechanisms whereby coatings improve LMO capacity retention. Herein, the effects of a new protective coating material, La 0.5 Sr 0.5 CoO 3 (LSCO), in a thin‐film battery geometry that is amenable to fundamental studies of electrode processes, are reported. RF sputtering deposition is used to produce high quality 25–100 nm LMO cathodes on Al 2 O 3 substrates with an intervening Pt/Ti back‐side contact layer. Cycling of the un‐coated cathodes results in capacity loss of 18% over 300 cycles. Adding a 2 nm LSCO layer reduces the capacity loss to 3%. While this may be due in part to reduced Mn dissolution, scanning transmission electron microscopy results indicate that the coating helps to preserve crystallinity and reduce lattice structure distortion due to inhibited formation of defect tetragonal spinel. Three‐electrode electrochemical impedance spectroscopy results reveal that the LSCO coating increases charge transfer and ohmic resistances, but the increases are generally too small to significantly impact cell performance even at high C‐rates.

25 ENERGY STORAGE↗
DOE OSTI2023

Suppressed phase segregation for triple-junction perovskite solar cells

The tunable band gaps and facile fabrication of perovskites make them attractive for multi-junction photovoltaics. However, light-induced phase segregation limits their efficiency and stability: this occurs in wide band gap (> 1.65 eV) I/Br mixed perovskite absorbers, and becomes even more acute in the top cells of triple-junction solar photovoltaics that requires a fully 2.0 eV band gap absorber. We report herein that lattice distortion in I/Br mixed perovskites is correlated with the suppression of phase segregation, generating an increased ion migration energy barrier arising from the decreased average interatomic distance between A-site cation and iodide. Using a ~2.0 eV Rb/Cs mixed-cation inorganic perovskite with large lattice distortion in the top subcell, we fabricated all-perovskite triple-junction solar cells and achieved an efficiency of 24.3% (23.3% certified quasi-steady-state efficiency) with an open-circuit voltage of 3.21 V. This is, to our knowledge, the first reported certified efficiency for perovskite-based triple-junction solar cells. The triple-junction devices retain 80% of their initial efficiency following 420 hours of operation at the maximum power point.

14 SOLAR ENERGY↗
DOE OSTI2023

GaSb doping facilitates conduction band convergence and improves thermoelectric performance in n-type PbS

P-type lead chalcogenides have superior thermoelectric performance because they exhibit the energy convergence of several valence bands. However, despite the existence of two conduction bands, there has been no report about conduction band (CB) convergence for n-type counterparts because of the large energy difference between them. Therefore, new strategies are required to manipulate the CBs if enhancing the electrical transport performance of n-type lead chalcogenides is to be achieved. PbS is a highly attractive member of the lead chalcogenides because of its high earth-abundance and low cost. Here, we report that the introduction of GaSb can successfully dope the PbS matrix with Ga and Sb atoms occupying the Pb site in its rock salt structure. GaSb doping leads to conduction band convergence and enlarged effective density of state mass for n-type PbS. This effect results in superior power factor and decreased lattice thermal conductivity caused by the soft phonon modes and point defect scattering of phonons. Consequently, a record-high average power factor PF avg of ~20.4 μW cm –1 K –2 and figure of merit ZT avg of ~0.84 in the temperature range of 400 K to 923 K were obtained, higher than any n- and p-type PbS-based thermoelectric materials.

36 MATERIALS SCIENCE↗