Search NASA⌕ Search

Engineering topics

Druffel, Thad

Publications and source records attributed to Druffel, Thad.

32 records · Page 2

Copper Electrode on Flexible Substrate by Intense Pulsed Light Sintering of Microsized Copper Particles

Metal electrodes deposited in a grid pattern onto flexible polymer substrates have been shown to be a viable alternative to replace indium tin oxide (ITO) as the transparent anode for organic photovoltaics. copper may be a better alternative in terms of cost and stability for large area low-cost solar modules, specifically on roll-to-roll platforms. These customized electrode patterns can be fabricated from copper nanoparticles through various printing techniques applicable to solution phase processing. The Intense Pulsed Light (IPL) technique has been used to sinter copper nanoparticles (~100nm) to fabricate conductive copper electrodes on flexible polymer substrates. However, compared to nanosized (~100 nm) copper particles, microsized (~2 um) copper is much cheaper. In this work, microsized (~2 um) copper is used to produce high conductive copper inks. The conductivity of the print can be adjusted through the use of surfactant. IPL sintering was optimized to obtain high conductivity copper films. In conclusion, several microscopic and electrical spectroscopic characterization techniques such as scanning electron microscopy (SEM), x-ray diffraction (XRD), 4-point probe resistivity measurements were employed to characterize the copper electrodes.

14 SOLAR ENERGY↗

Fabrication of Flexible Perovskite Solar Cells via Rapid Thermal Annealing

Adaptability, lightweight, and low cost of materials make flexible perovskite solar cells essential for the perovskite technology to breach commercial photovoltaic market. Roll-to-roll manufacturing has great potential for high-throughput perovskite manufacturing; however, conventional annealing methods are not capable of producing flexible perovskite solar cells at scale. Rapid thermal annealing (RTA), a radiative method, is utilized on roll-to-roll lines within many different industries and has shown promising potential for perovskite annealing. Here, we introduce a blade-coated perovskite thin film on flexible ITO-coated PET annealed via RTA that reduces post-deposition processing time from ~150 seconds to ~14 seconds. Performance was not sacrificed for scalability as a perovskite solar cell was produced with a power conversion efficiency (PCE) of 14.58%.

Martin, Blake↗

Phase-Transition Interlayer Enables High-Performance Solid-State Sodium Batteries with Sulfide Solid Electrolyte

All-solid-state sodium (Na) batteries (ASSSBs) using sulfide-based solid electrolytes (SEs) have attracted intensive attention due to their superior safety, high energy density and low cost. However, interfacial issue is one of the biggest challenges to achieve high-performance sulfide-based ASSSBs due to the serious reactions between active Na metal and sulfide SEs at the interface. To address the interfacial challenges, we propose in this paper a simple and efficient approach by introducing a polymer electrolyte as an interlayer to stabilize the interface. Na 3 SbS 4 as a model sulfide SE is used to demonstrate the interlayer strategy to stabilize the interface by preventing the detrimental reactions and inhibiting Na dendrites. As a result, stable Na plating/stripping was observed in Na symmetric cells under the current density of 0.1 mA cm –2 . Moreover, ASSSBs with Na metal and TiS 2 electrode delivered long-term stability over 300 cycles remaining a specific capacity above 100 mAh g –1 , and FeS 2 ||Na cells exhibited an impressive specific capacity of up to 200 mAh g –1 after the 20th cycles. This work demonstrates an efficient strategy to address interfacial challenges between sulfide SEs and Na metal, which contributes to the development of ASSSBs in next-generation energy storage systems.

25 ENERGY STORAGE↗

Intense Pulse Light Annealing of Perovskite Photovoltaics Using Gradient Flashes

Perovskite solar cells (PSCs) have been fabricated through high-speed and low-cost depositions but often require long annealing. Intense pulse light (IPL) can anneal thin films in seconds after deposition by inducing very high temperatures lasting for milliseconds, and multiple flashes can be used to tune the temperature profile. In this study, a gradient flash annealing (GFA) approach is introduced and compared to uniform flash annealing (UFA) by investigating the crystallinity, morphology, and phase evolution of the CH 3 NH 3 PbI 3 perovskite films and their impact on PSC performance. Unlike UFA, low-intensity pulsed irradiation during the pre-annealing stage of GFA played a significant role on enhancing the PSC performance by forming pure-phase CH 3 NH 3 PbI 3 perovskite thin films with superior morphology and high crystallinity. To understand the kinetics, a transient thermal simulation using ANSYS was developed and confirmed with an experimental setup. The results combined with microscopy and spectrophotometry were used to visualize how duration, delay time, photon flux, and flash count parameters participated in crystallization, phase, and morphology evolution. The IPL annealing induced rapid surface temperature increase, reaching as high as 800 °C, while produced well-developed and bound perovskite grains without any surface defects in an uncontrolled ambient environment with high humidity (>60%). The study resulted in PSCs with maximum efficiency and fill factor of 9.27 and 69.92% for the UFA and 11.75 and 68% when annealed through the GFA approach, respectively. Lastly, this work utilized IPL as the sole thermal source for post-deposition annealing to rapidly fabricate efficient PSCs in only 10 s, which opens the pathway for high-speed, low-cost, and large-scale automated fabrication of perovskite photovoltaics and semiconductors.

14 SOLAR ENERGY↗

Interface stability of LiCl-rich argyrodite Li 6 PS 5 Cl with propylene carbonate boosts high-performance lithium batteries

In solid-state lithium (Li)-metal batteries (SSLMBs), sulfide-based Li-ion conductors represent one of the most popular solid electrolytes (SEs). However, the development of sulfide-based SSLMBs is significantly hampered by interfacial issues including large solid-solid contact resistance and serious side reactions at the SE/electrode interface. To address these issues, here, we demonstrated a simple and efficient strategy by using LiCl-rich argyrodite Li 6 PS 5 Cl (Li 6 PS 5 Cl-LiCl) SE and trace amount of propylene carbonate (PC) at the SE/electrode interface to facilitate the formation of stable and robust solid electrolyte interphase (SEI). Additionally, the formed SEI not only serves as a buffer layer to passivate the interfacial reactions and suppress Li dendrite growth, but also acts as a bridge for Li-ion conduction to reduce the contact resistance. As a result, the Li||Li symmetric cell exhibited long-term electrochemical cycling stability over 1000 h at a current density of 0.2 mA cm -2 . Furthermore, the assembled Li||Li 4 Ti 5 O 12 (LTO) batteries delivered a specific capacity of 175 mAh g–1 at 0.2 C, and remained an excellent specific capacity of 116 mAh g –1 after 200 cycles at a high current rate of 1 C. These features indicate a feasible strategy to enhance the interfacial property of high-performance SSLMBs.

25 ENERGY STORAGE↗

Regulated lithium ionic flux through well-aligned channels for lithium dendrite inhibition in solid-state batteries

The utilization of solid electrolyte (SE) to suppress lithium (Li) dendrites is promising but still far from satisfactory due to the inhomogeneous Li plating/stripping. In this paper, we demonstrated a novel strategy to inhibit Li dendrites via regulating Li-ion flux in SE by using vertically aligned channels. The ion-insulating walls facilitated uniform distribution of Li-ion flux through the channels, leading to a homogeneous Li deposition, thus alleviating Li dendrite formation. As a result, symmetric cells with this SE exhibited excellent long-term stability (1000 h) against Li metal. In addition, Li4Ti5O12 (LTO)/Li cell with the developed SE achieved good battery performance over 100 cycles. The mechanism for dendrite suppression was further investigated by phase-field simulation. This work provides a novel strategy by manipulating uniform Li-ion flux to fabricate SE to inhibit Li dendrites and facilitates the development of high-performance rechargeable Li batteries.

25 ENERGY STORAGE↗

Fabrication of flexible perovskite solar cells via rapid thermal annealing

Adaptability, lightweight, and low cost of materials make flexible perovskite solar cells essential for the perovskite technology to breach commercial photovoltaic markets. Roll-to-roll manufacturing has great potential for high-throughput perovskite manufacturing; however, conventional annealing methods are not capable of producing flexible perovskite solar cells at scale. Conventional methods are time consuming and may compromise functionality of flexible substrates under tension. Here, we introduce a bladecoated perovskite thin film on flexible ITO-coated PET annealed via rapid thermal annealing (RTA) that reduces post-deposition processing time from ~150 s to ~14 s. As a result, performance was not sacrificed for scalability as a perovskite solar cell was produced with a power conversion efficiency (PCE) of 14.58%.

14 SOLAR ENERGY↗

Roll-to-roll Manufacturing of Continuous Perovskite Modules

This project researched the development of inks that were roll-to-roll compatible and that could reduce processing time to achieve high speed operation. This necessitated the development of two nanoparticle inks, tin oxide (SnO 2 ) and nickel oxide (NiO) as electron transport layer (ETL) and hole transport layer (HTL) respectively. Several PVSK inks were also developed including a methyl ammonium lead iodide (MAPI), a mixed cation chemistry (MC) and a triple cation (TC) chemistry. All of these layers were demonstrated in roll-to-roll compatible processes utilizing Intense Pulsed Light (IPL) processing.

14 SOLAR ENERGY↗