Search NASA⌕ Search

Engineering topics

Duan, Jiaqi

Publications and source records attributed to Duan, Jiaqi.

11 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Microstructural evolution in a precipitate-hardened (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 multi-principal element alloy during high-pressure torsion

Multi-principal element alloys demonstrate high strength, thermal stability, and irradiation resistance, making them excellent candidate materials for applications in nuclear reactors and other harsh environments. Some studies have examined the use of high-pressure torsion to strengthen MPEAs through grain size reduction and strain hardening. However, no studies have investigated the effect of HPT on secondary phases (precipitates) within an MPEA. Two alloys, (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 containing Ni(Ti, Al) B2 phase, and CrFe σ phase, and single-phase Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 , were fabricated by casting and heat treatment. Both alloys were then processed with HPT to study microstructural evolution. Scanning electron microscopy (SEM) and transmission electron microscopy (TEM) were used to characterize the alloys before and after HPT processing. HPT processing produced a nanocrystalline structure in both alloys, but (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 exhibited a significantly smaller grain size and higher dislocation density than Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 , with corresponding higher hardness. Before HPT, the (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 94 Ti 2 Al 4 alloy consisted of large grain (~ 400 μm) and precipitates, including B2 of ~ 38 μm average size, B2 of ~ 0.7 μm average size, and small amounts of σ of ~ 1.5 μm average size. After HPT, the larger B2 precipitates were decreased in size and volume fraction, while the smaller B2 precipitates were completely dissolved; the σ precipitates appeared unaffected by HPT, likely due to their much higher hardness. Finally, observation of the B2 precipitate distribution along radial distance indicates that the strain caused the precipitates to fracture at intermediate strain (γ = 125) and dissolve at high strain (γ = 280).

36 MATERIALS SCIENCE↗
DOE OSTI2024

Effect of impurities on phase transformation and precipitation in a low-carbon steel

Impurity elements have been added to a commercial low carbon steel grade to simulate the levels that could arise as a result of increased scrap recycling during steel production. In this study, continuous cooling transformation (CCT) diagrams were constructed for the steels with varying levels of impurities, and it is shown that impurities suppress the phase transformation across a wide range of cooling rates. It was found that a step was formed in the start temperature curve, separating the reconstructive and displacive transformations. The influence of impurities on both the reconstructive transformation and displacive transformation are discussed. Additionally, Cu precipitates were observed using scanning transmission electron microscopy (STEM) in the highest impurity-containing steel after slow cooling (0.05°C/s), fast cooling (5°C/s) and interrupted cooling. It was found that the precipitation kinetics is in the following order: cementite within the secondary phase and cementite at secondary phase-ferrite interface> ferrite grain boundaries> ferrite grain matrix. Atom-probe tomography (APT) revealed Cu precipitates formed on the surface of cementite lamellae, but not within it. This work offers insights for the phase transformation control and precipitation regulation during the thermomechanical processing of low carbon steels containing impurity elements due to scrap recycling.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Comparison of the Thermal Stability in Equal‐Channel‐Angular‐Pressed and High‐Pressure‐Torsion‐Processed Fe–21Cr–5Al Alloy

Nanostructured steels are expected to have enhanced irradiation tolerance and improved strength. However, they suffer from poor microstructural stability at elevated temperatures. In this study, Fe–21Cr–5Al–0.026C (wt%) Kanthal D (KD) alloy belonging to a class of (FeCrAl) alloys considered for accident‐tolerant fuel cladding in light‐water reactors is nanostructured using two severe plastic deformation techniques of equal‐channel angular pressing (ECAP) and high‐pressure torsion (HPT), and their thermal stability between 500–700 °C is studied and compared. ECAP KD is found to be thermally stable up to 500 °C, whereas HPT KD is unstable at 500 °C. Microstructural characterization reveals that ECAP KD undergoes recovery at 550 °C and recrystallization above 600 °C, while HPT KD shows continuous grain growth after annealing above 500 °C. Enhanced thermal stability of ECAP KD is from significant fraction (>50%) of low‐angle grain boundaries (GBs) (misorientation angle 2–15°) stabilizing the microstructure due to their low mobility. Small grain sizes, a high fraction (>80%) of high‐angle GBs (misorientation angle >15°) and accordingly a large amount of stored GB energy, serve as the driving force for HPT KD to undergo grain growth instead of recrystallization driven by excess stored strain energy.

Arivu, Maalavan↗
DOE OSTI2023

A high-strength precipitation hardened cobalt-free high-entropy alloy

Recent studies on precipitation-hardened high-entropy alloys (HEAs) demonstrate their high strength and thermal stability, making them promising materials for high-temperature structural applications such as nuclear reactors. However, many existing HEAs contain cobalt (Co), which is unsuitable for nuclear applications because of the long-term activation issue of Co. Co is also expensive and considered a critical material for other applications. Therefore, it is desired to exclude Co from the composition. A Co-free (Fe 0.3 Ni 0.3 Mn 0.3 Cr 0.1 ) 88 Ti 4 Al 8 HEA was developed and studied in this work. In contrast to previous Co-free HEAs, this alloy is close to equiatomic in its composition and promises a more pronounced high-entropy effect. Scanning electron microscopy, transmission electron microscopy, atom probe tomography, and synchrotron-based, high-energy X-ray diffraction were used to characterize this alloy and revealed a complex four-phase structure, with an FCC matrix, γ’ precipitates, and a network of B2 and χ phase particles. This structure granted 2151 MPa compressive strength and good thermal stability, but with limited ductility and slow precipitation kinetics. A strengthening analysis of the alloy shows that the B2 and χ provided the most significant strengthening contribution, adding 312 MPa and 788 MPa respectively. Furthermore the strengthening effect from the nanoscale γ' is also considerable, adding 608 MPa in total. This study lays the foundation for the continued development of high-strength Co-free HEAs with improved and satisfactory ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Effects of microstructure on the oxidation behavior of A3 matrix‐grade graphite

Abstract The oxidation behavior of matrix‐grade graphite in air‐ or steam‐ingress accident scenarios is of great interest for high‐temperature gas reactors (HTGRs). In this study, the microstructures of two variants of matrix‐grade graphite based on the German A3‐3 and A3‐27 formulations were characterized with scanning electron microscopy (SEM), transmission electron microscopy (TEM), and Raman spectroscopy, and correlated to oxidation behavior observed through thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC). Through TEM imaging and selected area electron diffraction (SAED), a higher volume fraction of partially graphitized carbon was identified in the A3‐3 type graphite than in the A3‐27 type. This structure is believed to have contributed to the accelerated oxidation exhibited by A3‐3 in the chemical reaction‐controlled oxidation regime.

Bratten, Adam↗