Search NASA⌕ Search

Engineering topics

Duan, Lian

Publications and source records attributed to Duan, Lian.

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2020

Direct Numerical Simulations of Acoustic Disturbances in Various Rectangular Nozzle Configurations

We perform Direct Numerical Simulations (DNS) to study the acoustic freestream disturbances radiating from the turbulent boundary layers along the contoured nozzle walls of a hypersonic wind tunnel with a rectangular test section. To begin with, the effects of the spanwise end walls are suppressed by confining the spanwise computational domain to a finite segment of the overall nozzle cross section and by imposing periodic boundary conditions across that spanwise domain. Besides providing a building-block configuration to reveal par- tial effects of the enclosed acoustic environment within the wind tunnel, these computations serve as a stepping stone toward the goal of fully-3D computations including the nozzle end walls. Building upon the earlier simulations of Deegan et al. (2018), we show that the computed acoustic characteristics in the spanwise periodic simulations are insensitive to changes in the grid resolution parameters (e.g., x+ and z+). This is relative to the previous simulations that involved a coarser resolution in the streamwise and wall-normal directions, especially up- stream of the test section. Furthermore, we outline a comparison of the pressure fluctuations induced by the turbulent boundary layers over the contoured nozzle walls and several other calculations involving boundary layers over a single flat plate at nearly the same value of the edge Mach number. We also show the impact of having only one turbulent boundary layer instead of two within the computational setup. Various flow statistics, including the first and second moments of the unsteady flow field, are computed for the different flow configurations. Good comparisons of the statistics of the nozzle-wall boundary-layer turbulence and of the freestream acoustic disturbances between the simulations of coarser and finer grids confirms DNS procedure, but also the insensitivity of noise characteristics t section to the inflow turbulence generation technique.

Hildebrand, Nathaniel↗
NASA NTRS2019

Stabilization of a Swept-Wing Boundary Layer by Discrete Roughness Elements at High Reynolds Numbers

Direct numerical simulations (DNS) are performed to study potential stabilizing ef- fect of spanwise periodic discrete roughness elements (DREs) on cross ow instabilities in a spatially developing three-dimensional boundary layer over an in nite-swept natural- laminar- ow wing at a freestream Mach number of 0:75 and a chord Reynolds number of approximately 25 million. In the DNS, both the spanwise periodic DREs and distributed roughness in the leading-edge region are implemented to simulate a typical experimen- tal scenario in which multiple steady cross ow modes including the most unstable mode (i.e., the \target" mode) emerge because of the presence of naturally distributed surface roughness in the leading edge region and spanwise periodic control cylinders of subcritical wavelength are used to force small-wavelength disturbances (i.e., the control mode) for damping the target mode. The DNS results show that the e ectiveness of DRE control is sensitive to roughness diameter, height, and chordwise placement. For the DRE parame- ters considered in this study, the stabilizing e ect on the target mode is small within the computational domain that ended at about 35% of the chord.

Nicholson, Gary↗
NASA NTRS2018

Direct Numerical Simulation of Receptivity to Roughness in a Swept-Wing Boundary Layer at High Reynolds Numbers

Direct numerical simulations (DNS) are performed to examine the receptivity to roughness in a spatially developing three-dimensional boundary layer over an in finite-swept natural-laminar-flow wing at a free stream Mach number of 0:75 and a chord Reynolds number of approximately 25 million based on the long, swept chord. Stationary cross ow disturbances are excited by applying either critically spaced discrete cylinders of micron size or naturally occurring distributed roughness in the leading-edge region. The DNS data show that the spanwise spectral content of the excited cross ow disturbances is highly dependent upon the shape of roughness elements, and the initial growth of the cross ow structures is a nonlinear function of the element height. The linear growth rate of the excited cross ow disturbances predicted by DNS shows good agreement with linear parabolized stability equations. The receptivity study lays the foundation for investigating the stabilization of the naturally most unstable steady cross ow mode by using spanwise periodic DREs.

Nicholson, Gary↗
NASA NTRS2018

Direct Numerical Simulation of Acoustic Disturbances in the Rectangular Test Section of a Hypersonic Wind Tunnel

Direct numerical simulations (DNS) of the full-scale rectangular nozzle of a hypersonic wind tunnel are conducted to study the acoustic freestream fluctuations radiating from turbulent boundary layers (TBLs) along the nozzle walls. The nozzle geometry and the flow conditions of the DNS match those of the NASA 20-Inch Mach 6 Tunnel, and the DNS has been completed for a domain without spanwise sidewall boundary conditions. The turbulent boundary layer parameters based on the DNS compare well with those derived from Reynolds Averaged Navier-Stokes (RANS) calculations as well as with the predictions based on Pate’s correlation. A similarly good comparison is observed for both the Mach number distribution and the Reynold’s stresses obtained from the DNS and RANS calculations, respectively. Various characteristics of the acoustic pressure fluctuations within the inviscid core of the nozzle flow are compared with those associated with a single flat plate at a similar freestream Mach number. The frequency spectrum and bulk propagation speeds match well between the nozzle and the flat plate, but the rms pressure fluctuation is higher for the nozzle configuration, likely due to the combined effect of acoustic radiation from the top and bottom walls. Spatial contours of the two-point correlation coefficient display elliptical tails with approximately equal but opposite angles corresponding to the preferred directionality of acoustic structures radiated from both walls. Future work will focus on DNS of the full nozzle configuration, including the effects of the nozzle side walls.

Deegan, Cole P.↗
NASA NTRS2018

Characterization of Freestream Disturbances in Conventional Hypersonic Wind Tunnels

While low disturbance ("quiet") hypersonic wind tunnels are believed to provide more reliable extrapolation of boundary layer transition behavior from ground to flight, the presently available quiet facilities are limited to Mach 6, moderate Reynolds numbers, low freestream enthalpy, and subscale models. As a result, only conventional ("noisy") wind tunnels can reproduce both Reynolds numbers and enthalpies of hypersonic flight configurations, and must therefore be used for flight vehicle test and evaluation involving high Mach number, high enthalpy, and larger models. This article outlines the recent progress and achievements in the characterization of tunnel noise that have resulted from the coordinated effort within the AVT-240 specialists group on hypersonic boundary layer transition prediction. New Direct Numerical Simulation (DNS) datasets elucidate the physics of noise generation inside the turbulent nozzle wall boundary layer, characterize the spatiotemporal structure of the freestream noise, and account for the propagation and transfer of the freestream disturbances to a pitot-mounted sensor. The new experimental measurements cover a range of conventional wind tunnels with different sizes and Mach numbers from 6 to 14 and extend the database of freestream fluctuations within the spectral range of boundary layer instability waves over commonly tested models. Prospects for applying the computational and measurement datasets for developing mechanism-based transition prediction models are discussed.

Duan, Lian↗
NASA NTRS2017

Direct Numerical Simulation of Acoustic Noise Generation from the Nozzle Wall of a Hypersonic Wind Tunnel

The acoustic radiation from the turbulent boundary layer on the nozzle wall of a Mach 6 Ludwieg Tube is simulated using Direct Numerical Simulations (DNS), with the flow conditions falling within the operational range of the Mach 6 Hypersonic Ludwieg Tube, Braunschweig (HLB). The mean and turbulence statistics of the nozzle-wall boundary layer show good agreement with those predicted by Pate's correlation and Reynolds Averaged Navier-Stokes (RANS) computations. The rms pressure fluctuation P'(rms)/T(w) plateaus in the freestream core of the nozzle. The intensity of the freestream noise within the nozzle is approximately 20% higher than that radiated from a single at pate with a similar freestream Mach number, potentially because of the contributions to the acoustic radiation from multiple azimuthal segments of the nozzle wall.

Huang, Junji↗
NASA NTRS2017

Direct Numerical Simulation of Hypersonic Turbulent Boundary Layer inside an Axisymmetric Nozzle

As a first step toward a study of acoustic disturbance field within a conventional, hypersonic wind tunnel, direct numerical simulations (DNS) of a Mach 6 turbulent boundary layer on the inner wall of a straight axisymmetric nozzle are conducted and the results are compared with those for a flat plate. The DNS results for a nozzle radius to boundary-layer thickness ratio of 5:5 show that the turbulence statistics of the nozzle-wall boundary layer are nearly unaffected by the transverse curvature of the nozzle wall. Before the acoustic waves emanating from different parts of the nozzle surface can interfere with each other and undergo reflections from adjacent portions of the nozzle surface, the rms pressure fluctuation beyond the boundary layer edge increases toward the nozzle axis, apparently due to a focusing effect inside the axisymmetric configuration. Spectral analysis of pressure fluctuations at both the wall and the freestream indicates a similar distribution of energy content for both the nozzle and the flat plate, with the peak of the premultiplied frequency spectrum at a frequency of [(omega)(delta)]/U(sub infinity) approximately 6.0 inside the free stream and at [(omega)(delta)]/U(sub infinity) approximately 2.0 along the wall. The present results provide the basis for follow-on simulations involving reverberation effects inside the nozzle.

Huang, Junji↗
NASA NTRS2016

Direct Numerical Simulation of Transition Due to Traveling Crossflow Vortices

Previous simulations of laminar breakdown mechanisms associated with stationary crossflow instability over a realistic swept-wing configuration are extended to investigate the alternate scenario of transition due to secondary instability of traveling crossflow modes. Earlier analyses based on secondary instability theory and parabolized stability equations have shown that this alternate scenario is viable when the initial amplitude of the most amplified mode of the traveling crossflow instability is greater than approximately 0.03 times the initial amplitude of the most amplified stationary mode. The linear growth predictions based on the secondary instability theory and parabolized stability equations agree well with the direct numerical simulation. Nonlinear effects are initially stabilizing but subsequently lead to a rapid growth followed by the onset of transition when the amplitude of the secondary disturbance exceeds a threshold value. Similar to the breakdown of stationary vortices, the transition zone is rather short and the boundary layer becomes completely turbulent across a distance of less than 15 times the boundary layer thickness at the completion of transition.

Li, Fei↗
NASA NTRS2016

Stationary Crossflow Breakdown due to Mixed Mode Spectra of Secondary Instabilities

Numerical simulations are used to study laminar breakdown characteristics associated with stationary crossflow instability in the boundary-layer flow over a subsonic swept-wing configuration. Previous work involving the linear and nonlinear development of individual, fundamental modes of secondary instability waves is extended by considering the role of more complex, yet controlled, spectra of the secondary instability modes. Direct numerical simulations target a mixed mode transition scenario involving the simultaneous presence of Y and Z modes of secondary instability. For the initial amplitudes investigated in this paper, the Y modes are found to play an insignificant role during the onset of transition, in spite of achieving rather large, O(5%), amplitudes of RMS velocity fluctuation prior to transition. Analysis of the numerical simulations shows that this rather surprising finding can be attributed to the fact that the Y modes are concentrated near the top of the crossflow vortex and exert relatively small influence on the Z modes that reside closer to the surface and can lead to transition via nonlinear spreading that does not involve interactions with the Y mode. Finally, secondary instability calculations reveal that subharmonic modes of secondary instability have substantially lower growth rates than those of the fundamental modes, and hence, are less likely to play an important role during the breakdown process involving complex initial spectra.

Li, Fei↗
NASA NTRS2016

Acoustic Radiation From a Mach 14 Turbulent Boundary Layer

Direct numerical simulations (DNS) are used to examine the turbulence statistics and the radiation field generated by a high-speed turbulent boundary layer with a nominal freestream Mach number of 14 and wall temperature of 0:18 times the recovery temperature. The flow conditions fall within the range of nozzle exit conditions of the Arnold Engineering Development Center (AEDC) Hypervelocity Tunnel No. 9 facility. The streamwise domain size is approximately 200 times the boundary-layer thickness at the inlet, with a useful range of Reynolds number corresponding to Re 450 􀀀 650. Consistent with previous studies of turbulent boundary layer at high Mach numbers, the weak compressibility hypothesis for turbulent boundary layers remains applicable under this flow condition and the computational results confirm the validity of both the van Driest transformation and Morkovin's scaling. The Reynolds analogy is valid at the surface; the RMS of fluctuations in the surface pressure, wall shear stress, and heat flux is 24%, 53%, and 67% of the surface mean, respectively. The magnitude and dominant frequency of pressure fluctuations are found to vary dramatically within the inner layer (z/delta 0.< or approx. 0.08 or z+ < or approx. 50). The peak of the pre-multiplied frequency spectrum of the pressure fluctuation is f(delta)/U(sub infinity) approx. 2.1 at the surface and shifts to a lower frequency of f(delta)/U(sub infinity) approx. 0.7 in the free stream where the pressure signal is predominantly acoustic. The dominant frequency of the pressure spectrum shows a significant dependence on the freestream Mach number both at the wall and in the free stream.

Zhang, Chao↗
NASA NTRS2015

Acoustic Radiation from High-Speed Turbulent Boundary Layers in a Tunnel-Like Environment

Direct numerical simulation of acoustic radiation from a turbulent boundary layer in a cylindrical domain will be conducted under the flow conditions corresponding to those at the nozzle exit of the Boeing/AFOSR Mach-6 Quiet Tunnel (BAM6QT) operated under noisy-flow conditions with a total pressure p(sub t) of 225 kPa and a total temperature of T(sub t) equal to 430 K. Simulations of acoustic radiation from a turbulent boundary layer over a flat surface are used as a reference configuration to illustrate the effects of the cylindrical enclosure. A detailed analysis of acoustic freestream disturbances in the cylindrical domain will be reported in the final paper along with a discussion pertaining to the significance of the flat-plate acoustic simulations and guidelines concerning the modeling of the effects of an axisymmetric tunnel wall on the noise field.

Duan, Lian↗
NASA NTRS2014

Analysis of Numerical Simulation Database for Pressure Fluctuations Induced by High-Speed Turbulent Boundary Layers

Direct numerical simulations (DNS) of Mach 6 turbulent boundary layer with nominal freestream Mach number of 6 and Reynolds number of Re(sub T) approximately 460 are conducted at two wall temperatures (Tw/Tr = 0.25, 0.76) to investigate the generated pressure fluctuations and their dependence on wall temperature. Simulations indicate that the influence of wall temperature on pressure fluctuations is largely limited to the near-wall region, with the characteristics of wall-pressure fluctuations showing a strong temperature dependence. Wall temperature has little influence on the propagation speed of the freestream pressure signal. The freestream radiation intensity compares well between wall-temperature cases when normalized by the local wall shear; the propagation speed of the freestream pressure signal and the orientation of the radiation wave front show little dependence on the wall temperature.

Duan, Lian↗
NASA NTRS2014

Nonlinear Development and Secondary Instability of Traveling Crossflow Vortices

Transition research under NASA's Aeronautical Sciences Project seeks to develop a validated set of variable fidelity prediction tools with known strengths and limitations, so as to enable "sufficiently" accurate transition prediction and practical transition control for future vehicle concepts. This paper builds upon prior effort targeting the laminar breakdown mechanisms associated with stationary crossflow instability over a swept-wing configuration relevant to subsonic aircraft with laminar flow technology. Specifically, transition via secondary instability of traveling crossflow modes is investigated as an alternate scenario for transition. Results show that, for the parameter range investigated herein, secondary instability of traveling crossflow modes becomes insignificant in relation to the secondary instability of the stationary modes when the relative initial amplitudes of the traveling crossflow instability are lower than those of the stationary modes by approximately two orders of magnitudes or more. Linear growth predictions based on the secondary instability theory are found to agree well with those based on PSE and DNS, with the most significant discrepancies being limited to spatial regions of relatively weak secondary growth, i.e., regions where the primary disturbance amplitudes are smaller in comparison to its peak amplitude. Nonlinear effects on secondary instability evolution is also investigated and found to be initially stabilizing, prior to breakdown.

Li, Fei↗
NASA NTRS2014

Direct Numerical Simulations of High-Speed Turbulent Boundary Layers over Riblets

Direct numerical simulations (DNS) of spatially developing turbulent boundary layers over riblets with a broad range of riblet spacings are conducted to investigate the effects of riblets on skin friction at high speeds. Zero-pressure gradient boundary layers under two flow conditions (Mach 2:5 with T(sub w)/T(sub r) = 1 and Mach 7:2 with T(sub w)/T(sub r) = 0:5) are considered. The DNS results show that the drag-reduction curve (delta C(sub f)/C(sub f) vs l(sup +)(sub g )) at both supersonic speeds follows the trend of low-speed data and consists of a `viscous' regime for small riblet size, a `breakdown' regime with optimal drag reduction, and a `drag-increasing' regime for larger riblet sizes. At l l(sup +)(sub g) approx. 10 (corresponding to s+ approx 20 for the current triangular riblets), drag reduction of approximately 7% is achieved at both Mach numbers, and con rms the observations of the few existing experiments under supersonic conditions. The Mach- number dependence of the drag-reduction curve occurs for riblet sizes that are larger than the optimal size, with smaller slopes of (delta C(sub f)/C(sub f) for larger freestream Mach numbers. The Reynolds analogy holds with 2(C(sub h)=C(sub f) approximately equal to that of at plates for both drag-reducing and drag-increasing configurations.

Duan, Lian↗
NASA NTRS2013

Direct Numerical Simulation of Transition in a Swept-Wing Boundary Layer

Direct numerical simulation (DNS) is performed to examine laminar to turbulent transition due to high-frequency secondary instability of stationary crossflow vortices in a subsonic swept-wing boundary layer for a realistic natural-laminar-flow airfoil configuration. The secondary instability is introduced via inflow forcing derived from a two-dimensional, partial-differential-equation based eigenvalue computation; and the mode selected for forcing corresponds to the most amplified secondary instability mode which, in this case, derives a majority of its growth from energy production mechanisms associated with the wall-normal shear of the stationary basic state. Both the growth of the secondary instability wave and the resulting onset of laminar-turbulent transition are captured within the DNS computations. The growth of the secondary instability wave in the DNS solution compares well with linear secondary instability theory when the amplitude is small; the linear growth is followed by a region of reduced growth resulting from nonlinear effects before an explosive onset of laminar breakdown to turbulence. The peak fluctuations are concentrated near the boundary layer edge during the initial stage of transition, but rapidly propagates towards the surface during the process of laminar breakdown. Both time-averaged statistics and flow visualization based on the DNS reveal a sawtooth transition pattern that is analogous to previously documented surface flow visualizations of transition due to stationary crossflow instability. The memory of the stationary crossflow vortex is found to persist through the transition zone and well beyond the location of the maximum skin friction.

Duan, Lian↗
NASA NTRS2013

Towards Bridging the Gaps in Holistic Transition Prediction via Numerical Simulations

The economic and environmental benefits of laminar flow technology via reduced fuel burn of subsonic and supersonic aircraft cannot be realized without minimizing the uncertainty in drag prediction in general and transition prediction in particular. Transition research under NASA's Aeronautical Sciences Project seeks to develop a validated set of variable fidelity prediction tools with known strengths and limitations, so as to enable "sufficiently" accurate transition prediction and practical transition control for future vehicle concepts. This paper provides a summary of selected research activities targeting the current gaps in high-fidelity transition prediction, specifically those related to the receptivity and laminar breakdown phases of crossflow induced transition in a subsonic swept-wing boundary layer. The results of direct numerical simulations are used to obtain an enhanced understanding of the laminar breakdown region as well as to validate reduced order prediction methods.

Choudhari, Meelan M.↗