Search NASA⌕ Search

Engineering topics

Duane M Revilock

Publications and source records attributed to Duane M Revilock.

5 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2026

Impact Testing of 410 Stainless Steel for Material Impact Model Development

A project is underway to develop a consistent set of material properties, impact test data, and failure analysis for a variety of metallic aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the Federal Aviation Administration William J. Hughes Technical Center. Particular features of this set of data are that all material property and impact test data are obtained using traceable material, the test methods and procedures are extensively documented, and all the raw data are available. Four parallel efforts are currently underway: measurement of material deformation and failure response over a wide range of strain rates and temperatures, failure analysis of material property specimens and impact test articles, development of improved numerical modeling techniques for deformation and failure, and impact testing of flat panels and substructures for model validation. This report describes impact testing performed on 410 stainless steel sheet and plate samples of different thicknesses with two different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

410 Stainless Steel↗
NASA NTRS2024

Hopkinson Bar Impact Force Measurement for Application to Development of an Artificial Bird

A test method has been published for measuring forces from bird cadavers and artificial birds to demonstrate equivalency to support the use of artificial birds in aircraft certification testing. The test method involves a large diameter Hopkinson bar as the technique for measuring and comparing forces. The method involves the assumption that a force on one end of the bar results in a one-dimensional plane wave that travels down the bar. To avoid reflected waves from the end of the bar overlapping the input pulse, and due to practical limitations on the length of the bar, strain transducers are located relatively close to the impacted face of the bar, raising questions about the validity of the assumption of one-dimensional wave propagation. In addition, the large diameter of the bar can introduce dispersion effects in the propagated pulse. These must be assessed to determine the impact on the accuracy of impact force measurements and, if significant, dispersion correction techniques must be used. In this study analytical, experimental, and computational methods are used to analyze the wave propagation characteristics for impact forces expected from realistic bird impacts. While wave dispersion and effects of non-concentric impacts are present, the resulting errors are relatively small. For the response we expect to see in bird impacts up to velocities of approximately 300 m/sec the large diameter Hopkinson bar test appears to be an acceptable method for measuring the impact forces and comparing the response of real and proposed artificial birds.

Birdstrike↗
NASA NTRS2020

Impact Testing of Inconel 718 for Material Impact Model Development

One of the difficulties with developing and verifying accurate impact models is that parameters such as high strain-rate material properties, failure modes, static properties, and impact test measurements are often obtained from a variety of different sources using different materials, with little control over consistency among the different sources. In addition, there is often a lack of quantitative measurements in impact tests to which the models can be compared. To alleviate some of these problems, a project is underway to develop a consistent set of material property, impact test data, and failure analysis for a variety of aircraft materials that can be used to develop improved impact failure and deformation models. This project is jointly funded by the NASA Glenn Research Center and the Federal Aviation Administration (FAA) William J. Hughes Technical Center. Unique features of this set of data are that all material property and impact test data are obtained using traceable material, the test methods and procedures are extensively documented, and all of the raw data is available. Four parallel efforts are currently underway. The Ohio State University conducts both measurement of material deformation and failure response over a wide range of strain rates and temperatures and failure analysis of material property specimens and impact test articles. The George Mason University conducts the development of improved numerical modeling techniques for deformation and failure. Glenn conducts the impact testing of flat panels and substructures. This report describes impact testing performed on Inconel 718 sheet and plate samples of different thicknesses with different types of projectiles, one a regular cylinder and one with a more complex geometry incorporating features representative of a jet engine fan blade. Data from this testing will be used in validating material models developed under this program. The material tests and the material models developed in this program will be published in separate reports.

J Michael Pereira↗
NASA NTRSDate not supplied

Simulating High Energy Dynamic Impact of IM7/PEKK Continuous Fiber Laminated Thermoplastic Composite using Open Hole Coupon Experiments

The use of advanced thermoplastic composites (TPC) for structural applications in the aerospace and automotive industries has grown increasingly popular due to their high performance, high manufactured part output, and sustainability. Enhancing verification simulations of the progressive failure in TPCs at the coupon scale is needed to better validate advanced composite material models at larger length scales, such as element level panels. MAT_213, a tabulated composite material model, has been applied to simulate high velocity dynamic impact (HEDI) and is integrated in the LS-DYNA explicit finite element (FE) software. Previous efforts using MAT_213 have calibrated HEDI simulated failures with experimental data. Traditionally simulations have relied on a structured mesh to represent quasi-isotropic panels. For this study, a continuous fiber unidirectional tape, IM7/PEKK, was analyzed through a series of verification studies of notched laminate coupons, then validation analyses of quasi-isotropic panels under HEDI were compared with experimental data. Experiments using unidirectional TPC were performed to obtain tabulated stress vs strain curves using Digital Image Correlation (DIC) for input into MAT_213. Next, notched coupon experiments were used as an intermediate step to calibrate the damage and failure behavior in MAT_213. Lastly, investigations into differences between HEDI simulations using a fiber aligned mesh were compared with experimental failure patterns and damage sizes. The use of experimentally generated material behavior along with selective mesh layout improved HEDI predictions with minimal material parameter calibration.

Polymer matrix composites↗