Search NASA⌕ Search

Engineering topics

Duenow, Joel N.

Publications and source records attributed to Duenow, Joel N..

17 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Characterization of n-Type Iodine-Doped and Indium-Doped CdTe/Cd-Se-Te Thin Films Fabricated by Close-Spaced Sublimation Epitaxy

In this study, n-type CdTe thin films, specifically iodine-doped CdTe (CdTe:I), indium-doped CdTe (CdTe:In), and indium-doped Cd-Se-Te (CST:In), were synthesized using close-spaced sublimation epitaxy (CSSE). Characterization techniques secondary ion mass spectrometry (SIMS), electron backscatter diffraction (EBSD), Hall-effect measurements, and time-resolved photoluminescence (TRPL) were employed to analyze the chemical, structural, and electronic properties of these materials. The results indicated epitaxial single crystal CSSE films grew on the single crystal substrates, with carrier density ranging from 10^14 - 10^16 cm -3 , and after post-annealing, the minority-carrier lifetimes reach near the radiative limit. Additionally, a preliminary exploration of homojunction structures with an n- type (CdTe:In /CST:In /CdTe:I) /CdTe:P /Cu /Mo configuration was performed. The best device performance was achieved with CdTe:I including CdS aiding in band alignment, resulting in a power conversion efficiency (..eta..) of 2.61% with open circuit voltage (Voc) of 850 mV, fill factor (FF) of 47.8%, and short-circuit current (Jsc) of 6.44 mA/cm 2 . The observed low Jsc and efficiency may be attributed to a buried junction and a poor interface, due to dopant interdiffusion. Consequently, further investigations focusing on interface optimization, diffusion blocking, and reduced recombination through passivation, are crucial to enhancing the efficiency of CSSE CdTe homojunction devices in the future.

cadmium compounds↗
DOE OSTI2024

Structural and Electronic Properties of Indium-Doped n-type Cd-Se-Te Crystals

Here, we present a comprehensive investigation into the potential of n-type indium-doped cadmium selenide telluride (CST:In) as a high-performance candidate for solar cell applications, without the need for resource-intensive post-growth treatments that are required for CdTe:In. We compared undoped CST and CST:In crystals under different growth conditions, analyzing their structural and electronic properties using x-ray diffraction (XRD), electron probe microanalysis (EPMA), current-voltage (IV) and Hall effect measurements, time-resolved photoluminescence (TRPL), optical transmission, and photoluminescence (PL) mapping. The results reveal that as-grown CST:In crystals achieve nearly 100% carrier activation, yielding an electron concentration of 9.5x1018 cm -3 , mobility of 653 cm 2 /V.s and a 5 ns lifetime which approaches the radiative limit. Furthermore, comparison of PL maps from crystal growths having different cooling profiles suggests a strong effect of cooling rate on selenium segregation and cubic/hexagonal/polytype phase distribution. Slower cooling leads to a more homogeneous cubic structure with lower Se segregation, while a faster cooling rate results in increased Se segregation, and twin boundaries and stacking faults with polytypic and hexagonal character.

14 SOLAR ENERGY↗
DOE OSTI2023

Intra-Grain Local Luminescence Properties of CdSe0.1Te0.9 Thin Films

We report on the local photoluminescence properties of grains and grain boundaries of CdSe 0.1 Te 0.9 thin film deposited by the colossal grain growth method using a wide-field hyperspectral imaging technique. We observed significant variations in the photoluminescence intensity of both individual grains and also that of grain boundaries. Multiple sub-bandgap defect peaks were captured in the luminescence spectra in the energy range 1.2 eV to 1.6 eV. The intensity and peak positions of these sub-gap emissions were slightly different among various grains and at the grain boundaries, revealing intra- and inter-grain variations in these polycrystalline thin films. A recently-developed density-of-states based photoluminescence model was extended to include multiple peaks and was fitted to the data. We observed that at a fixed temperature, the quasi-Fermi level splitting energy and a disordered energy parameter can be extracted locally by use of this model.

data models↗
DOE OSTI2023

Imaging local luminescence variations in CdSe 0.1 Te 0.9 thin films grown by the colossal grain growth process

Clear visualization and understanding of luminescence properties of grain interiors and grain boundaries in polycrystalline thin-film photovoltaic materials are crucial to achieving high-performance solar cells. Luminescence-based measurements, for example, reveal sub-bandgap energetic disorder or impurity-related radiative transitions in these materials, and when performed in the absolute scale, they can show the extent of voltage-limiting non-radiative recombination. Here we use a hyperspectral imaging technique to investigate inter- and intra-grain photoluminescence variations in polycrystalline CdSe 0.1 Te 0.9 films made by the colossal grain growth process. We observe that grain boundaries show higher luminescence than grain interiors for all energies below the bandgap energy. Multiple distinct sub-bandgap defect transitions are detected and determined to be related to donor-acceptor pair impurities. A comparison of the excitation-intensity-dependent photoluminescence at the grain boundaries with grain interiors suggests that carrier concentration is higher at grain boundaries. This finding is supported by photoemission electron microscopy imaging of the films, showing approximately 70 meV upward energy shift in the band structure at the grain boundaries. Finally, we investigate a dramatic thermal quenching behavior related to the donor-acceptor pairs luminescence over a temperature range and use a rate-equation model to attribute it to the sudden redirection of the radiative recombination channels to non-radiative channels with increasing temperature.

14 SOLAR ENERGY↗
DOE OSTI2023

Nanometer-scale electrical potential imaging on absorber of CdSeTe solar cells

Here, we report on nm-scale electrical potential imaging throughout As-doped and Cu-doped CdSeTe absorbers using Kelvin probe force microscopy (KPFM). The potential imaging was conducted both laterally and vertically on beveled films using ion milling at small glancing angle. KPFM images electrical potential on the beveled surface and assesses defect charging in the subsurface region within a screening length from the beveled surface. We found that the grain boundaries were positively charged and that there were significant potential fluctuations in both grain boundary versus grain interior and intragrain. We further found that these potential fluctuations decreased significantly toward the front interface. Time of flight secondary ion mass spectrometry imaging shows that Se content increased toward the front interface, consistent with Se passivation of defects. The potential fluctuation was induced by defect charging, and the results elucidate different details of the defect configurations and grain structures of the films with different CdCl 2 treatment temperatures in the As-doped CdSeTe. The defect configurations in the region near the front interface can be a main factor contributing to the device performance difference. Our potential imaging provides insights about the defects throughout the absorber films, and shows that the potential fluctuation has a direct correlation to the V oc deficit.

14 SOLAR ENERGY↗
DOE OSTI2023

The Effect of Dopant Concentration and Annealing Treatments on N-Type Iodine Doped CdTe

We report properties of highly conducting n-type cadmium telluride single crystals doped with iodine (CdTe:I). These crystals were grown with dopant concentrations in the range of 10^17 cm-3 to 10^19 cm-3 by Modified Vertical Bridgman (MVB) melt growth. Post-growth dopant activation, including Cd annealing, Te annealing, and rapid thermal annealing (RTA), was applied to improve free carrier density. The structural, optical, and electrical properties were analyzed by Glow Discharge Mass Spectroscopy (GDMS), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD), Photoluminescence Spectroscopy (PL), optical absorption, Hall measurements, Capacitance-Voltage (CV) measurements, and time-resolved photoluminescence (TRPL). The results indicate that Cd annealing is the most effective activation method to get 100% donor activation (n is approximately 2 x 10^18 cm-3), which is close to the room temperature solubility limit of iodine. This leads to the lowest resistivity and the highest mobility. Moreover, this data suggests a potential role of Cd vacancy-related defects on electrical self-compensation.

annealing↗
DOE OSTI2022

Titanium Carbide MXene Hole Contacts for CdTe Photovoltaics

CdTe is a high‐efficiency thin‐film photovoltaic technology that has seen tremendous commercial success over the past decade. Yet despite the improvement of other device characteristics, the fabrication of an ohmic hole back contact layer has remained a challenge due to the high ionization potential of CdTe, which limits the external potential that can be feasibly reached even as other characteristics of the device improve. MXenes, a family of 2D materials with rapidly growing scientific and commercial interest, offer a promising route to forming low‐cost, low‐barrier contacts due to their demonstrated high work function, metallic conductivity, and facile solution processing from benign solvents. Here, it is shown that Ti 3 C 2 T x MXene films processed from an aqueous colloidal dispersion can perform as a highly efficient hole contact material for CdTe solar cells, resulting in high power‐conversion efficiencies. The role of the Schottky barrier formation in Ti 3 C 2 T x ‐contacted CdTe devices is probed, and potential pathways for the future development of this potent combination of materials are elucidated. The modularity of the expansive MXene family of materials presents a promising strategy for developing next‐generation hole contacts for CdTe solar cells.

14 SOLAR ENERGY↗
DOE OSTI2021

Dual-Wavelength Time-Resolved Photoluminescence Study of CdSe x Te 1-x Surface Passivation via Mg y Zn 1-y O and Al 2 O 3

Voltage loss is currently one of the biggest challenges facing cadmium telluride (CdTe) based photovoltaics. Determining the location(s) of major voltage loss within the device stack (e.g., front/back interface, grain boundaries) is therefore of primary interest. Here, we present a custom-built time-resolved photoluminescence system with two excitation wavelengths - 670 (standard) and 405 nm - to probe the device stack at depths of approximately 130 and 35 nm, respectively; their comparison helps differentiate interface and bulk contributions to carrier lifetime. We apply this system to examine the passivation effect of two significant recent advances in CdTe: the incorporation of Se to form graded CdSe x Te 1-x and the replacement of CdS with Mg y Zn 1-y O. It is found that x = 0.2 Se is required to obtain lifetime improvements, primarily in the bulk. Additionally, evidence for trapping at the Mg y Zn 1-y O/CdSe x Te 1-x interface was observed. Furthermore, this indicates further work is required to sufficiently passivate the front interface.

CdSeTe↗
DOE OSTI2021

Carrier Lifetime as a Function of Se Content for CdSexTe1-x Films Grown on Al2O3 and MgZnO: Preprint

Time-resolved photoluminescence (TRPL) with two excitation wavelengths – 670 (standard) and 405 nm – was used to examine the effect on carrier lifetime of two significant recent advances in CdTe: the incorporation of Se to form graded CdSe x Te 1-x and the use of Mg y Zn 1-y O buffers. The two excitation wavelengths probe depths of approximately 130 and 35 nm, respectively, and their comparison helps differentiate interface and bulk contributions to carrier lifetime. It was found that x = 0.2 Se was required to obtain lifetime improvements, primarily in the bulk. Additionally, TRPL traces for Mg y Zn 1-y O/CdSe x Te 1-x samples showed fast initial decay followed by a long-lived tail, which may be indicative of trap-dominated recombination. This behavior was not present for CdSe x Te 1-x films grown on Al 2 O 3 , which is currently state-of-the-art for surface passivation in CdTe. This indicates that further work is required to sufficiently passivate the front interface.

cadmium telluride↗
DOE OSTI2021

Carrier Lifetime as a Function of Se Content for CdSexTe1-x Films Grown on Al2O3 and MgZnO

Time-resolved photoluminescence (TRPL) with two excitation wavelengths – 670 (standard) and 405 nm – was used to examine the effect on carrier lifetime of two significant recent advances in CdTe: the incorporation of Se to form graded CdSe x Te 1-x and the use of Mg y Zn 1-y O buffers. The two excitation wavelengths probe depths of approximately 130 and 35 nm, respectively, and their comparison helps differentiate interface and bulk contributions to carrier lifetime. It was found that x = 0.2 Se was required to obtain lifetime improvements, primarily in the bulk. Additionally, TRPL traces for Mg y Zn 1-y O/CdSe x Te 1-x samples showed fast initial decay followed by a long-lived tail, which may be indicative of trap-dominated recombination. This behavior was not present for CdSe x Te 1-x films grown on Al 2 O 3 , which is currently state-of-the-art for surface passivation in CdTe. This indicates that further work is required to sufficiently passivate the front interface.

cadmium telluride↗
DOE OSTI2021

Exceeding 200 ns Lifetimes in Polycrystalline CdTe Solar Cells

CdTe photovoltaics has achieved one of the lowest levelized costs of electricity among all energy sources. However, for decades, carrier lifetimes have been inferior to those of other prevalent solar cell materials. This quality has inhibited common methods to improve solar cell efficiency such as back-surface fields, electron reflectors, or bifacial solar cells. In this work, a significant increase in carrier lifetime to values exceeding 200 ns in fully functional CdTe solar cells is demonstrated. The increased lifetime is achieved by large CdSeTe grains at the absorber/emitter interface, intragrain passivation in the absorber layer, and chemical passivation by forming nanoscale oxidized tellurium species at the transparent conducting oxide interface. The carrier lifetime is correlated to the open-circuit voltage and enables paths for back-surface manipulation and novel cell architectures to further improve CdTe photovoltaic performance.

14 SOLAR ENERGY↗
DOE OSTI2021

Optimization of Source Material for in-situ Arsenic Doping via Vapor Transport Deposition of CdTe Films

In-situ doping of CdTe/CdSeTe films with arsenic is performed using pre-doped source material prepared by high pressure Bridgman (HPB) melt growth. Arsenic level in the source material is varied from 1018-1020 cm-3. Correspondingly, dopant incorporation in the films prepared using vapor transport deposition (VTD) varied from 3x1017 cm-3–1x1018cm-3. In this range, dopant activation is found to inversely correlate with the dopant incorporation, suggesting compensation. The results from this study indicate film properties can be adjusted by source material.

41 EE - Solar Energy Technologies Office (EE-4S)↗
DOE OSTI2020

Se diffusion in CdTe thin films for photovoltaics

Manipulating CdSeTe bandgrading to enhance photocurrent and carrier lifetime is an essential part of high-performance CdTe photovoltaics (PVs). Here, we examine Se diffusion kinetics in single-crystal and polycrystalline CdTe during deposition, thermal annealing, and CdCl 2 treatments. Se distributions are determined by dynamic secondary-ion-mass spectroscopy and Auger electron spectroscopy depth profiling and coupled with electron backscatter diffraction images of the crystalline structure. Effective bulk and grain boundary diffusion coefficients are determined by analytical models and discussed in the context of processing and film morphology. Se is found to diffuse in CdTe at much higher rates during CdCl 2 treatments than with thermal processing alone. GB diffusion also occurs at a significantly faster rate than bulk diffusion. As a result of these two effects, the near interface bulk and GB Se diffusion during CdCl 2 treatments dominates the bandgrading profiles in CdTe PVs.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Thin-Film Solar Cells with 19% Efficiency by Thermal Evaporation of CdSe and CdTe

CdTe-based solar cells exhibiting 19% power conversion efficiency were produced using widely available thermal evaporation deposition of the absorber layers on SnO2-coated glass with or without a transparent MgZnO buffer layer. Evaporating CdSe and CdTe sequentially by thermal evaporation and subsequent CdCl2 annealing establishes efffective CdSeTe band grading as well as dense, large-grain films. These results show that high-performance II-VI photovoltaics can be made by inexpensive, commercially available evaporation systems without the need to build customized equipment, enabling CdTe photovoltaics research and manufacturing to be more accessible to the broader photovoltaics community.

14 SOLAR ENERGY↗