Search NASA⌕ Search

Engineering topics

Dunand, David C.

Publications and source records attributed to Dunand, David C..

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Recent progress in high-temperature superconducting undulators

Considerable effort has been devoted to the development of superconducting undulators (SCUs) intended for particle accelerator-based light sources, including synchrotrons and free electron laser (FEL) facilities. Recently, a high-temperature superconducting (HTS) undulator prototype, consisting of staggered-array Re-Ba-Cu-O bulks, achieved an on-axis sinusoidal magnetic field profile with a peak amplitude B$_0$ of 2.1 T and a period length of 10 mm, resulting in a deflection parameter K = 1.96. Such a short period HTS undulator not only enables the generation of higher-energy photons, but also supports the construction of economically feasible and compact FELs with shorter linear accelerators (LINACs). This article provides a comprehensive review of recent advances in the staggered-array bulk HTS undulator as well as other types of HTS undulators. Furthermore, it offers insights into the development of engineering HTS undulator prototypes designed for deployment in synchrotron and free electron laser (FEL) facilities. We conclude by discussing opportunities for and the challenges facing the use of HTS undulators in practical applications.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Hypereutectic Al-Ce-X (X=Mn, Cr, V, Mo, W) alloys fabricated by laser powder-bed fusion

Here, we characterize the microstructures and high-temperature mechanical properties of Al-2Ce and ternary Al-2Ce-1X (at.%) alloys fabricated by laser powder-bed fusion (LPBF), where X = Mn, Cr, V, Mo, and W are slow-diffusing transition metals. All ternary alloys show a hypereutectic microstructure in the as-LPBF state, containing an interconnected network of eutectic Al 11 Ce 3 phases (~10 vol.%) and an additional population of submicron, equiaxed Al 20 CeX 2 primary precipitates (~10 vol.%) which are isomorphous among these five alloys. Similar microstructures are present in arc-melted rods and atomized powders but are coarser due to the slower cooling rates in these processes. The hardness of the as-LPBF ternary Al-Ce-X alloys (1300–1400 MPa) is higher than that of the binary Al-Ce alloy (~1100 MPa) due to the higher volume fraction of strengthening phases. Furthermore, during exposure at 400 °C for up to three months, greater hardness retention is achieved in the ternary Al-Ce-X alloys (65–75%) than in the binary Al-Ce alloy (~55%), which is attributed to the extreme coarsening resistance of the Al 20 CeX 2 precipitates imparted by the very slow-diffusing ternary solute. These coarsening-resistant Al 20 CeX 2 precipitates also substantially improve alloy creep resistance, increasing the threshold stress for dislocation creep at 300°C from ~32 MPa for the binary Al-Ce alloy to ~77–100 MPa for the ternary Al-Ce-X alloys, and at 400°C from <10 MPa for the binary Al-Ce alloy to >40 MPa for the ternary Al-Ce-V alloy.

36 MATERIALS SCIENCE↗
DOE OSTI2024

3D-ink-printing of monocrystalline YBCO superconductor

Single-crystal microstructure can bring high performance for many materials includingpiezoelectrics1, 2, semiconductors3, 4, and cuprate superconductors5. Unlike single-crystal metalsthat can be machined into complex components6, most single-crystal ceramics are limited to theshape of thin films or plates due to their brittleness. However, more designs of advanced devicesneed to break these geometric limitations. 3D-ink-printing can efficiently fabricate complex architectured ceramics, but the microstructure is polycrystals. Here, for the first time, we demonstrate a route to grow single-crystal on 3D printed ceramic-YBa2Cu3O7-x (YBCO)superconductors that can simultaneously have complex architectures and high critical currentdensity. An ink containing precursor powders was 3D extruded and sintered to obtain polycrystalYBCO micro-lattices. A single-crystal seed is then utilized to grow single crystal on 3D-printedmicro-lattices by melt growth method. We found that the geometric details of 3D printed microlatticecan survive after it went through liquid + solid phase region above its peritectic temperature.More complex YBCO single-crystal parts, such as horizontal and toroidal coils, were thensuccessfully fabricated. In addition, Origami can be implemented on our 3D printed sample to increase their complexity. This research provides a new way to develop superconducting devicessuch as undulators for synchrotron radiation and microwave cavities for dark-matter axion search7.We expect this new process will inspire more studies about 3D printing of single-crystal ceramics. For example, 3D printing of BaTiO3 can be developed to grow a single crystal8 for the applications of dielectric capacitors and transducers.

43 PARTICLE ACCELERATORS↗
DOE OSTI2024

Creep deformation and cavitation in an additively manufactured Al-8.6Cu-0.4Mn-0.9Zr (wt%) alloy

Creep deformation and cavitation were investigated at 300 ºC in both tension and compression for an additively manufactured Al-8.6Cu-0.5Mn-0.9Zr (wt%) alloy in the as-fabricated state and after various aging treatments (aging at 300 °C/200 h or 350 °C/24 h and overaging at 400 °C/200 h). Creep mechanisms at 300 °C were determined by relating the measured creep response to corresponding microstructural and X-ray computed tomography observations. In compression, alloys in the as-fabricated and two aging conditions exhibited similarly high creep resistance. Overaging (400 °C/200 h) led to substantial coarsening of intragranular θ-Al2Cu precipitates and an expected drop in their Orowan strengthening contribution. In tension, minimum strain rates comparable to those in compression were obtained at any given stress; however, upon accumulation of some plastic strain in the matrix, creep cavities started to form, leading to accelerated tertiary stage creep deformation and rupture. Cavitation occurred exclusively along melt pool boundaries due to locally enhanced diffusion enabled by (i) large grain-boundary area in adjacent fine-grained zones and (ii) localization of creep strain in nearby heat-affected zones. Although cavity growth was initially diffusion-controlled, its rate was determined by matrix creep rate, consistent with constrained cavity growth mechanisms. This study reveals how microstructural complexities induced by the additive manufacturing process affect the creep and cavitation behavior of Al-Cu-Mn-Zr alloys. The underlying creep and cavitation mechanisms uncovered in this study point to pathways that improve the high-temperature properties of additively manufactured alloys.

36 MATERIALS SCIENCE↗
DOE OSTI2024

An additively manufactured near-eutectic Al-Ce-Ni-Mn-Zr alloy with high creep resistance

A new additively manufactured (AM) Al-7.5Ce-4.5Ni-0.4Mn-0.7Zr (wt.%) near-eutectic alloy is reported, which shows unprecedented creep resistance up to 400 °C (a homologous temperature of 0.72). The eutectic solidification microstructure comprises ~ 27 vol% of coarsening-resistant second phase network with an ultrafine (<100 nm) inter-phase spacing. Both Mn and Zr contribute to creep resistance of the alloy. Small amount of Mn addition promotes selection of coarsening resistant phases without compromising the alloy processability. Zr not only improves hot-tearing resistance, but further enhances the second phase coarsening resistance resulting in improved creep resistance. Neutron diffraction performed during creep deformation reveals that the underlying mechanism for creep resistance in this alloy is impedance to dislocation motion stemming from the ultrafine eutectic solidification microstructure, whereas load transfer strengthening becomes less effective as the creep temperature increases. The second phase forms a continuous network in the as-fabricated condition, which is maintained during long-term creep at 300 °C. However, this network is fragmented into fine dispersoids at higher temperatures. It is proposed that the rate-limiting deformation mechanism at 300–400 °C is (i) dislocation climb for the alloy with fragmented second phase dispersoids and (ii) Orowan looping for the alloy with a continuous second phase network. In conclusion, the present design of an AM-processable multicomponent eutectic alloy with high creep resistance can be applied to other metallic systems exhibiting eutectic reactions, with expected extreme creep resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Combining solution-, precipitation- and load-transfer strengthening in a cast Al-Ce-Mn- Sc -Zr alloy

Here, a cast Al-9Ce-0.75Mn-0.18Sc-0.12Zr (wt%) alloy is designed to combine three strengthening phases: (i) micron-scale Al 11 Ce 3 platelets formed during eutectic solidification, (ii) nano-scale L1 2 -Al 3 (Sc,Zr) precipitates formed during aging, and (iii) Mn in solid solution in the α-Al matrix. Microstructural analyses by SEM, TEM, and atom-probe tomography reveal that Mn remains in solid solution in the as-cast alloy, providing solution strengthening with no influence on the eutectic Al-Al 11 Ce 3 microstructure, which provides precipitation- and load-transfer strengthening. During long-term over-aging at 400 °C, Mn-rich precipitates grow at the Al-Al 11 Ce 3 interface, with no effect on the microhardness. However, after short aging at 350 °C, a high number density of fine L1 2 -Al 3 (Sc,Zr) nanoprecipitates form in the Al matrix (with a coarser size at the Al-Al 11 Ce 3 interface), providing precipitation strengthening. The synergistic combination of the three strengthening mechanisms (solution, precipitation, and load transfer) in our Al-Ce-Mn-Sc-Zr alloy results in higher microhardness after aging at 350 and 400 °C, and higher creep resistance at 300 °C, as compared to alloys with two strengthening mechanisms: an Al-10Ce-0.93Mn control alloy (without precipitation strengthening from Sc and Zr), Al-Ce-Sc-Zr (without solution strengthening from Mn), and Al-Mn-Zr-Er (without load-transfer strengthening from Ce). Furthermore, these dual-strengthened alloys are more creep resistant than alloys with a single strengthening mechanism (Al-Ce, Al-Mn, and Al-Sc-Zr), confirming that the three mechanisms can be combined in pairs or all together.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure and strengthening of Al-6Ce-3Ni-0.7Fe (wt%) alloy manufactured by laser powder-bed fusion

In this study, an Al-6Ce-3Ni-0.7Fe (wt%) alloy was fabricated via laser powder-bed fusion and its microstructure, thermal stability, tensile properties, and creep properties are investigated for two rapid-solidification rates with different eutectic spacings. For both faster- and slower-cooled states, the as-fabricated alloy mostly shows elongated grains with very fine eutectic networks (~40 nm lamellar width) comprising a high-volume fraction (~18 %) of intermetallic phases. Faster-cooled samples, however, display a less continuous eutectic network with finer spacing (~100 nm), leading to higher Orowan strengthening and therefore superior microhardness and yield stress up to ~350 °C. Upon aging (300 - 450 °C), micron-size Al 9 (Ni,Fe) 2 needle-like precipitates form within grains, and the Al 11 Ce 3 eutectic network spheroidizes, while retaining a submicron width and spacing, resulting in 33–37 % drop in microhardness after 144 h aging at 400 °C. Limited tensile ductility (~6 %) and creep ductility (~1-2 %) are measured for both faster- and slower-cooled alloys due to an inhomogeneous microstructure, where cavitation preferentially initiates at melt-pool boundaries, precipitate-free zones, and/or denuded zones, eventually leading to local fracture. Denuded zones, induced by stress, form due to diffusional flow with stress-dependent orientations, and are identified as microstructurally weak regions leading to strain localization. The present alloy does not show a significant difference in 300 °C creep resistance between: (i) tensile and compressive loading, (ii) faster- and slower-cooled samples, and (iii) continuous and spheroidized eutectics. Creep resistance at 300 °C is comparable to that of a Ce-richer Al-10.5Ce-3.1Ni-1.2Mn (wt%) alloy, despite the formation of denuded zones and needle-like Al 9 (Ni,Fe) 2 precipitates.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Sintering inhibition enables hierarchical porosity with extreme resistance to degradation during redox cycling of Fe-Mo foams

High-temperature (800 ºC) steam-hydrogen redox cycling, relevant to grid-scale energy storage, is studied for iron-based freeze-cast lamellar foams. In contrast to previously studied Fe, Fe-Ni, and Fe-Co foams that rapidly degrade, Fe-25Mo foams feature a much-enhanced structural damage resistance. Utilizing in-situ x-ray diffraction, microscopy, and x-ray tomography, strong sintering inhibition is observed in Fe-Mo foams, creating a hierarchically porous lamellar structure. This leads to (i) wide channels between lamellae, enabling high macroscopic porosity (~78%) which can accommodate gas flow as well as volumetric expansion without lamellar contact, and (ii) microporosity within lamellae, providing additional free volume to accommodate expansion during oxidation, limiting both swelling of the lamellae and the formation of Kirkendall pores. Finally, these combined effects enable a near-complete reversibility of the microstructure during cycling, preventing damage produced via internal lamellar buckling, cracking, contacting and sintering, with a remarkably high porosity (65%) remaining after 50 consecutive redox cycles.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructure and mechanical properties of hypoeutectic Al–6Ce–3Ni-0.7Fe (wt.%) alloy

Here, a hypoeutectic, Fe-modified Al–Ce–Ni alloy (Al–6Ce–3Ni-0.7Fe, wt.%) is studied in terms of microstructure, thermal stability, ambient temperature strengthening, and creep resistance. The as-cast microstructure consists of primary Al dendrites and interdendritic binary eutectic regions (Al–Al11Ce3 and/or Al–Al9(Fe,Ni)2), with micron/submicron lamellar spacing, depending on the location along the height of the ingot. The cast alloy exhibits excellent coarsening resistance at 400 °C, with mostly unchanged microstructure and microhardness after 6 weeks of aging, indicating good thermal stability of Al11Ce3 and Al9(Fe,Ni)2. Orowan strengthening and load transfer are identified as strengthening mechanisms at ambient and elevated temperature. A high volume fraction of the intermetallic phases (providing load transfer) and relatively coarse eutectic spacing (for modest Orowan strengthening) result in a moderate as-cast microhardness of 566 ± 32 MPa. Creep resistance at 300 and 350 °C is similar to a binary Al-12.5Ce eutectic alloy (with twice the Ce content) because of two countering effects: Al–6Ce–3Ni-0.7Fe shows a higher volume fraction of strengthening intermetallic phases, but it also exhibits a large fraction of primary Al dendrites which weaken the alloy. By contrast, the alloy, when laser-remelted at the surface, has a fully eutectic microstructure without primary aluminum dendrites achieved by high undercooling on solidification, with a refined network of eutectic phases that doubles the microhardness as compared to the cast alloy. Whereas coarsening is faster due to the shorter diffusion distances between the eutectic phases, hardness remains ~30% higher than the as-cast alloy after ~6 weeks aging at 400 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Effect of grain-boundary θ-Al 2 Cu precipitates on tensile and compressive creep properties of cast Al–Cu–Mn–Zr alloys

Tensile and compressive creep tests were performed at 300 °C on high-temperature Al–Cu–Mn–Zr (ACMZ) alloys with 6 wt% Cu (6Cu) and 9 wt% Cu (9Cu) to evaluate the effect on creep properties of micron-size θ-Al 2 Cu intergranular precipitates. For compressive creep, the increased volume fraction of θ-precipitates at grain boundaries (from ~0.7% in 6Cu to ~ 6% in 9Cu) does not affect deformation rates across the investigated stress range of 15–110 MPa, consistent with creep being controlled by submicron θ'-Al 2 Cu precipitates within grains, whose size and fractions are the same in both alloys. In contrast, for tensile creep, 9Cu creeps faster than 6Cu at stresses above 20 MPa, and this difference increases with the stress level. Additionally, this discrepancy between tensile and compressive creep behavior is explained by cavitation during tensile creep, which is favored by higher volume fraction and larger size of intergranular θ precipitates in 9Cu. Conversely, larger precipitates impede cavity linkage resulting in improved creep ductility of 9Cu as compared to 6Cu at 300 °C.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Cavitation-resistant intergranular precipitates enhance creep performance of θ'-strengthened Al-Cu based alloys

Tensile and compressive creep properties of a quaternary Al-Cu-Mn-Zr (ACMZ) alloy and its commercial counterpart (Al-Cu-Mn-Zr with Ni, Co and Sb additions, RR350) are investigated at 300°C. At low stresses up to 30 MPa where diffusional creep dominates, creep resistance is the same in tension and compression and RR350 deforms more slowly than ACMZ, consistent with RR350 alloy's larger linear fraction of intergranular precipitates (Al7Cu2(NiFe) and Al9FeNi for RR350 vs. θ-Al2Cu for ACMZ) and a reduced fraction of precipitate-free zones near grain boundaries. At stresses between 30 and 80 MPa, dislocation creep with a stress exponent n ~ 3 becomes rate-limiting in compression, which is expected to be controlled by θ' precipitates within the grain bulk. By contrast, in tension, enhanced creep rate and higher apparent stress exponents are measured, consistent with cavitation at intergranular precipitates becoming increasingly dominant as the stress increases. In the dislocation creep regime, RR350 alloy is again more creep resistant than ACMZ alloy, which is related to three mechanisms (i) a reduced fraction of softer precipitate-free zones, (ii) more effective load transfer to intergranular precipitates, and (iii) reduced cavitation. A model for cavitation is applied to calculate tensile creep rates from compressive creep rates and the model successfully predicts the improved tensile creep resistance of the RR350 alloy. Overall, the present investigation underscores the importance of intergranular grain boundary precipitates, in addition to strengthening θ' precipitates, in enhancing the creep resistance of Al-Cu alloys.

36 MATERIALS SCIENCE↗