Search NASA⌕ Search

Engineering topics

Duque, Amanda L.

Publications and source records attributed to Duque, Amanda L..

Identification of Suitable Vacuum Gas Oils as Plasticizers Using HT-GC × GC-HRMS

Vacuum gas oils (VGOs) have long been heralded as effective plasticizers due to their high boiling-points and lubricating properties. One of these VGOs, HyVac Oil 93050, is a paraffinic plasticizer that is currently utilized in polymer–plasticizer explosive formulations, while this oil effectively increases the elasticity and decreases the sensitivity for current formulations. We seek to identify alternative VGOs with similar density, viscosity, molecular composition, and impurities for future formulations. In this study, 18 VGOs, including HyVac Oil 93050, were initially evaluated for their density and viscosity. The oils were then ranked based on physical characteristics and analyzed for molecular composition using high-temperature comprehensive two-dimensional gas chromatography with high-resolution time-of-flight mass spectrometry (HT-GC × GC-HRMS). Further, the HT-GC × GC-HRMS chromatograms of the top 10 most similar VGOs to HyVac Oil 93050, according to density, were compared utilizing the Pearson correlation coefficient. Three of the oils with densities similar to those of HyVac Oil 93050 had a Pearson correlation within the lot-to-lot variation of HyVac Oil 93050. For the top 3 candidates, Pearson correlation was then utilized as a feature selection technique to discover significant chemical differences. Positive chemical ionization (PCI) and negative chemical ionization (NCI) HT-GC × GC-HRMS chromatograms were also evaluated and aided in the discovery and identification of several key compounds including additives that acted as stabilizers for the VGOs. After this further chemical analysis, two of the original 17 potential VGOs were determined to be physically and chemically similar to HyVac Oil 93050.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructural investigation of PBX 9501: Comparing wet slurry and resonant acoustic mixing techniques

The microstructure of a high explosive (HE) material directly influences the reactive behavior under a variety of insults. Furthermore, the preparation method of polymer-bonded explosives (PBX), as well as the constituent material particle size distribution and consolidation parameters, will dominate the microstructural features that are observed. Here, we compare batches of PBX 9501 prepared by the typical wet slurry process and those prepared by resonant acoustic mixing. The “prills” produced by the wet slurry process leads to an inherently different microstructure than the coated powder produced by resonant acoustic mixing. Additionally, we observed that the conditions required to consolidate (press) the material to the nominal PBX 9501 density varied depending on the preparation technique, which also dictates the observed binder distribution. Furthermore, X-ray microcomputed tomography and ultra-small-angle X-ray scattering analyses revealed distinct differences in the void structure and distribution.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Novel method to control explosive shock sensitivity: Formulations, experiments and modeling

The microstructure of a heterogeneous high explosive (HE) affects its shock initiation sensitivity and detonation performance. Alteration of the void content and/or void structure (i.e., bulk heating or mechanical damage) therefore changes the shock initiation behavior. Controlling and predicting the change in shock sensitivity after an HE has undergone microstructural changes addresses an important and challenging goal for the design and understanding of novel energetic material formulations. In this study, we aimed to develop HE systems to precisely tune shock sensitivity by a thermal treatment prior to use. Specifically, we incorporated a small fraction (1 wt% or less) of thermally expandable microspheres (TEMs) during the formulation process of various plastic-bonded explosives (PBX). TEMs typically consist of a thermoplastic acrylonitrile shell (10-50 µm diameter), which encapsulates an inert low boiling hydrocarbon. Upon heating, the TEMs expand as the shell softens while the hydrocarbon gasifies, increasing the internal pressure and expanding the particle by as much as 120 vol% (irreversibly). Here, we present our progress on shock sensitivity comparisons of HE formulations doped with TEMs after heating and expansion. Experiments, using Composition C-4 thermally cycled to 120°C, showed an increase in shock sensitivity. Additionally, mesoscale modeling revealed that the TEM itself does not act as a hotspot, but instead has a secondary effect on the response of nearby voids. We conclude that TEMs indeed do provide a method to tune shock sensitivity. Further, our results emphasize the non-uniformity of shock waves at the mesoscale, and that upstream defects influence the reactivity of downstream defects.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Predicting the effects of thermally-induced density gradients on the hydrodynamic behavior of PBX 9502

High explosives are often exposed to thermal and mechanical stimuli within normal and abnormal environments. These stimuli can introduce density gradients in the explosive charge but the effect of such gradients is not well-understood. The goal of this work is to develop a comprehensive methodology to model the evolution of density gradients under various thermal conditions and then to predict shock initiation and detonation behavior of the gradated sample. PBX 9502 was chosen for these scoping studies because it has a large coefficient of thermal expansion and because the available shock initiation data indicates that initial temperature strongly affects the shock-to-detonation transition (SDT). The multiphysics code COMSOL was first used to model induced density gradients in a slab of PBX 9502 with asymmetric heating. Then, the gradated sample was constructed in the Pagosa hydrocode to simulate steel flyer impact scenarios, with SDT and detonation propagation following a calibrated Scaled Uniform Reactive Front (SURF) burn model. Furthermore, the gradated material exhibited very different initiation and corner turning behavior compared to homogeneous materials, and the orientation of the gradation was also found to have some effect. The methodology used here can estimate thermomechanical response of the material for non-uniform thermal environments and compute the resulting detonation properties of the PBX.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Microcomputed X-Ray Tomographic Imaging and Image Processing for Microstructural Characterization of Explosives

Microstructural characterization of composite high explosives (HEs) has become increasingly important over the last several decades in association with the development of high fidelity mesoscale modeling and an improved understanding of ignition and detonation processes. HE microstructure influences not only typical material properties (e.g., thermal, mechanical) but also reactive behavior (e.g., shock sensitivity, detonation wave shape). A detailed nondestructive 3D examination of the microstructure has generally been limited to custom-engineered samples or surrogates due to poor contrast between the composite constituents. Highly loaded (>90 wt%) HE composites such as plastic-bonded explosives (PBX) are especially difficult. Here, we present efforts to improve measurement quality by using single and dual-energy microcomputed X-ray tomography and state-of-the-art image processing techniques to study a broad set of HE materials. Some materials, such as PBX 9502, exhibit suitable contrast and resolution for an automatic segmentation of the HE from the polymer binder and the voids. Other composite HEs had varying levels of success in segmentation. Post-processing techniques that used commercially available algorithms to improve the segmentation quality of PBX 9501 as well as zero-density defects such as cracks and voids could be easily segmented for all samples. Aspects of the materials that lend themselves well to this type of measurement are discussed.

36 MATERIALS SCIENCE↗

Supplementary material for manuscript: Microcomputed X-ray Tomographic Imaging and Image Processing for Microstructural Characterization of Explosives

This data contains the supplemental information that will be accessible to the public from the paper “Microcomputed X-ray Tomographic Imaging and Image Processing for Microstructural Characterization of Explosives”. The data set contains the reconstructed slices for the 3D images of three different high explosives including: HMX-HTPB, PBX 9501 and PBX 9502. The data sets are folders of reconstructed tiffs showing the microstructure (crystals, binder, voids) and a segmented data set of each. Finally, a .gif movie is also present that plays the slices sequentially. The folders contain the voxel size information. See the manuscript for more details.

36 MATERIALS SCIENCE↗