Engineering topics

Duque, Amanda Lynn

Publications and source records attributed to Duque, Amanda Lynn.

11 records

DOE OSTI2023

Microwave ignition systems with launcher affixed to or located within a gun spindle

Microwave ignition systems with a launcher affixed to or located within a gun spindle. Use of a planar, impedance matched system that include a launcher affixed to or located within a gun spindle and a receiver affixed the propelling charge, where the receiver is engineered and impedance matched to efficiently deposit energy into the receiving igniter material, may result in significantly better timing and reliability than conventional mechanical gun ignition systems and other microwave ignition systems. A pressure-tolerant feed through system can route the microwave energy to the inside of the breech.

Duque, Amanda Lynn↗

DOE OSTI2023

Biologically inspired reinforcement using polydopamine of polymer bound composites

Interfacial strength plays a critical role in the mechanical properties of a composite system. In this work, a proven mock high explosive (HE), 5-iodo-2’-deoxyuridine (IDOX) was coated by the adhesive promoting polymer polydopamine (PDA), then formulated with an Estane binder system to form an improved HE mock composite. An extensive comparison study of mechanical properties was performed to determine the effects, if any, of PDA on the composite system. To aid in interpretation of the mechanical test data, neutron reflectometry experiments were performed to determine the thickness and structure of the as deposited PDA films. The mechanical performance of PDA-treated IDOX was then compared to untreated specimens by compression testing in the Brazilian disk geometry. The results strongly suggested that the structure of PDA consists of two layers: one low in density caused by polymer agglomerates attaching to the substrate during polymerization, and the second high in density caused by controlled linear deposition of polydopamine. Finally, the mechanical testing showed that PDA greatly increased the stiffness and yield strength of IDOX based mocks without causing any disruption to the underlying crystal system.

42 ENGINEERING↗

DOE OSTI2022

Novel method to control explosive shock sensitivity: A mesoscale study to understand the effect of thermally expandable microsphere (TEM) inclusions in high explosives (HE) microstructure

When the void content and/or void structure of a high explosive (HE) is altered by some means (i.e., bulk heating or mechanical damage), the shock initiation behavior of the material changes. The ability to precisely predict the change in shock sensitivity after an HE has undergone microstructural changes is a crucial capability in multi-scale reactive flow models. Here, we utilize thermally expandable microspheres (TEMs) as a dopant in a polymer bonded explosive (PBX) matrix to alter the shock initiation properties in a controlled fashion. Here, using a mesoscale modeling approach, we evaluated how a single TEM (before and after thermal expansion) behaves under shock compression, as well as how the matrix PBX in the direct vicinity of the TEM is affected. We first examined the effect of an unexpanded TEM in the explosive matrix and found that its presence does not significantly perturb the bulk flow and by extension will not affect bulk sensitivity. Next, we examined the effect of an expanded TEM and found that its presence significantly perturbs the flow via hydrodynamic jetting, which causes a secondary shock wave with a strength that exceeds that of the incident wave. Finally, we showed that this secondary shock interacts with the downstream porosity to ignite a larger fraction of the overall pore volume, commensurate with the secondary shock strength and the affected volume, increasing the global (bulk) shock sensitivity.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

DOE OSTI2022

Microstructural Effects of PETN on Detonator Performance

The strategic motivation of the project is guided by the Need to understand: material characteristics important to performance; how to most appropriately measure/monitor these characteristics; and, evolution of these characteristics through lifetime and storage conditions.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Production of desensitized, ultrafine PETN powder

Pentaerythritol tetranitrate (PETN) is a widely studied high explosive (HE), most commonly used in detonator applications. In this work, we use a spray drying technique to manufacture a new “nano-powder” morphology of PETN. The spray dried PETN is several orders of magnitude smaller in particle size than traditionally prepared PETN powders. The spray dried PETN has a mostly spherical and smooth morphology, while traditional crystalline PETN typically has sharp edges and crystal facets. Small-scale sensitivity tests including drop-weight impact, friction, and electrostatic discharge (ESD) indicate the spray dried PETN is less sensitive than traditionally used forms of PETN powders. Furthermore, we also observed no changes in chemical properties (melt temperature and onset of decomposition) after spray drying, and the material remains in the tetragonal, crystalline phase.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2021

Spray Drying of High Explosives [Slides]

Presentation Outline 1. What is spray drying? 2. How can spray drying be utilized for high explosives processing? 3. Literature overview. 4. Examples of current spray drying research done in Q-5. 5. Future plans and outlook for spray drying high explosives.

42 ENGINEERING↗

DOE OSTI2021

Composite binder, processing, and particle size effects on mechanical properties of non-hazardous high explosive surrogates

Plastic-bonded explosives (PBX) are polymer matrix composites that are highly loaded with micron-scale explosive crystals. The thermal and mechanical properties of these materials must be well-understood so that appropriate engineering models can be developed, but testing such properties under many scenarios can be hazardous and expensive. A non-hazardous PBX surrogate (“mock”) may be used in place of a PBX in many experiments if the thermomechanical properties are well-matched. Our previous research has shown that 5-iodo-2'-deoxyuridine (IDOX) is a promising crystalline filler material for the explosive cyclotetramethylene-tetranitramine (HMX). In this study, we investigate how the binder composition, variations in the IDOX particle size distribution, and pressing temperature affect the compressive strength and elastic modulus. We observe that while the binder system used in the composite dominates the mechanical response, the particle size distribution and pressing conditions do have a measurable effect on the material compliance and strength.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

DOE OSTI2020

Novel PBX formulations containing thermally-expandable microspheres for on-demand control of explosive behavior

In this work, we present the formulation and analysis of inert Plastic-Bonded eXplosive (PBX)-surrogates loaded with thermally expandable microspheres (TEMs). TEMs consist of a thermoplastic acrylonitrile shell (10-50 µm diameter) encapsulating an inert low boiling hydrocarbon. Upon heating, the TEMs expand as the shell softens while the hydrocarbon gasifies, increasing the internal pressure and expanding the particle by as much as 120 vol%. We hypothesize that TEM expansion within a PBX will introduce tunable changes in local density and porosity, and ultimately the shock sensitivity. This paper focuses on microstructural analysis of surrogate PBX-TEM formulations, both before and after thermally- induced TEM expansion. The formulations were analyzed by scanning electron microscopy (SEM), ultra-small angle neutron scattering (USANS), and X-ray Computed Tomography (x-ray CT) under various thermal conditions. Evidence suggests that TEM expansion within a PBX is a viable method to impart microstructural changes that are predicted to have a measurable, on-demand effect on the initiation sensitivity. Future work includes development of PBX-TEM formulations with HMX and shock initiation experiments.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2020

Formulation via Resonant Acoustic Mixing at LANL

Discussions in the middle of 2014 led researchers at LANL to seek an alternate formulation method for making PBX based explosives. We began looking into the use of Resonant Acoustic Mixers (RAM) to formulate explosives and mocks. Acoustic mixing had been used in pharmaceutical plants for mixing medicines and coating materials, so we envisioned transitioning that same technology to the energetics world. Up until this time only the wet slurry formulation method that had been used was from the 1940’s. This wet slurry method had been and still was the standard for all explosive formulations. The possibility of an alternate method needed to be looked at to advance the process by expanding solvent choices, substrates, and reducing costs. Acoustic mixing had been shown to mix powders, slurries, pastes or even liquids. A Resodyn LabRAM was purchased in late 2014 to explore these possible applications to energetics. This LabRAM was in a remote configuration that met our need for explosive operations.

36 MATERIALS SCIENCE↗

DOE OSTI2020

A Solubility Comparison of Cyclotetramethylenetetranitramine (HMX) and Potential Mock-HMX Candidates in Solvents Relevant to Slurry Formulating Polymer-Bonded Materials

Understanding solubility behavior of organic crystalline materials is critical in the development of slurry-formulated plastic bonded composites. In the field of high explosives (HE), a common method for obtaining high density, greater than 95 % theoretical maximum density, is to encapsulate HE in a polymer matrix resulting in the formation of plastic bonded explosive (PBX) prills. Prill formation is highly nuanced and requires understanding of particle size distributions, solvent, antisolvent, and binder system as well as interactions thereof. In this paper, in an effort to create mock-HE that mimics HE in density and mechanical strength, solubility of candidate molecules was compared to cyclotetramethylenetetranitramine (HMX) in binder solvents relevant to prill formation. The results indicate that the mock candidates chosen for this study have different solubilities compared to HMX in water and both organic solvents, 2-butanone and ethyl acetate, investigated. With these solubility differences known, prills to match PBXs based on HMX can be formulated, pressed and tested.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2020

Microwave ignition of energetic material housed within a gun

The systems and methods for microwave ignition of energetic material housed within a gun (e.g., primers and/or propellants) allow for the use of insensitive energetic materials and/or insensitive gas-generating materials in place of sensitive energetic materials relied upon by mechanical ignition systems. In some embodiments, the use of insensitive energetic materials and/or insensitive gas-generating materials increase the safety and reliability of guns that would otherwise need to depend on sensitive energetic material required by mechanical or laser ignition mechanisms. Additionally, in some embodiments, the systems and methods provide greater versatility with respect to the variety of energetic materials that may be employed within guns.

42 ENGINEERING↗