Search NASA⌕ Search

Engineering topics

E Lara Lash

Publications and source records attributed to E Lara Lash.

14 records
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Dynamic Mode Decomposition of Unsteady Pressure-Sensitive Paint Measurements for the NASA Unitary Plan Wind Tunnel Tests

This paper describes the Dynamic Mode Decomposition (DMD) of the pressures on the scale model of the Space Launch System (SLS) Block 1 cargo vehicle with the Unsteady Pressure-Sensitive Paint (uPSP) measurements, which were collected in the Ascent Transient Aerodynamics Tests with the Unitary Plan Wind Tunnel 11-by-11-foot Transonic Wind Tunnel in September 2019 at NASA Ames Research Center. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. The conventional DMD algorithm is based on the Singular Value Decomposition (SVD) of the data matrix. For the matrix of the uPSP measurements of the SLS ATAT, the number of rows is equal to the number of nodes in the grid of the scale model, and the number of columns is equal to the number of frames in the videos taken with 4 Phantom high-speed cameras. In this paper, it is verified that, for the time series with zero mean value, the DMD is equivalent to the decomposition with the Discrete Fourier Transform (DFT). Considering the uPSP is mainly used in the assessment of the unsteady, aerodynamic phenomena, the DMD of the uPSP measurements can be implemented in two steps: (1) subtract the mean value from the uPSP measurement on each of the grid nodes; (2) apply the Fast Fourier Transform (FFT) on the resulting zero-mean time series. The DMD of the uPSP measurements with FFT has two advantages: (1) the computational complexity of FFT is O(N*logN), where N is the length of the time series; (2) compared to the SVD-based DMD algorithm, the DMD with FFT can be easily implemented in parallel processing. A sample matrix of uPSP measurements, at the size of 341 grid nodes and 128 frames, is generated. Figures 1 and 2 show the eigenvalues and the ratios of the eigenvectors, respectively, of the sample matrix, without and with the mean value removed on each of the grid nodes, computed with the SVD-based DMD and the FFT. The figures demonstrate the equivalence of the SVD-based DMD and the decomposition with DFT/FFT for the time series with zero mean value. The results of DMD of the uPSP measurements of the SLS ATAT in September 2019 are presented in the paper. The DMD modes at different frequencies are shown, the aerodynamic phenomena (e.g. shockwave and vortex shedding) are demonstrated and the correlation of the DMD modes with the test configuration parameter (e.g., the Mach Number) is discussed. Figure 3 shows a software tool to visualize the DMD modes. The code to implement the algorithm described in this paper was written in C, with libraries of FFTW for FFT and MPI/OpenMP for parallel processing, and executed on the NASA Pleiades supercomputer. Funding for this research was provided by the NASA Aerosciences Evaluation and Test Capabilities Project.

Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

Dynamic Mode Decomposition of Unsteady Pressure-Sensitive Paint Measurements for the NASA Unitary Plan Wind Tunnel Tests

This paper discusses the Dynamic Mode Decomposition (DMD) of the Unsteady Pressure-Sensitive Paint (uPSP) measurements, which were collected with four Phantom high-speed cameras at a constant sample frequency in the Ascent Transient Aerodynamics Test (ATAT) of the Space Launch System (SLS) Block 1 cargo vehicle with the Unitary Plan Wind Tunnel (UPWT) 11-by-11-foot Transonic Wind Tunnel in September 2019 at NASA Ames Research Center. The conventional DMD algorithm is based on the Singular Value Decomposition (SVD). For the data with zero mean, the DMD is equivalent to the Discrete Fourier Transform (DFT). Since the uPSP is mainly used to determine the unsteady property of the aerodynamic flow, the DMD of the uPSP measurements is implemented in two steps: (1) subtract the mean value from the uPSP measurement; (2) apply the Fast Fourier Transform (FFT) on the resulting data with zero mean. The DMD of the uPSP measurements with FFT has two advantages: (1) the FFT algorithm is well known for its computational efficiency, therefore, compared to the SVD-based DMD algorithm, the DMD with FFT reduces the computation time; (2) the DMD with FFT can be easily implemented in parallel processing. The DMD outputs were generated with the execution in parallel of a code in C, with libraries of FFTW for FFT and MPI/OpenMP for parallel processing, on the NASA Pleiades supercomputer. In this paper, the results of DMD of the uPSP measurements in the tests of Mach sweep runs of the SLS ATAT are presented, and the effectiveness of the DMD of the uPSP measurements in the diagnosis of the unsteady, aerodynamic phenomena is demonstrated. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding for this research was provided by the NASA Aeroscience Evaluation and Test Capabilities Project.

Pressure-Sensitive Paint↗
NASA NTRSDate not supplied

Infrared Reflection Removal in Wind Tunnels using Polarization Theory

Infrared radiometry with infrared cameras allows for high spatial resolution, noncontact measurements in wind tunnel experiments and has been increasingly used to visualize flow features. Reflections from test section walls present a major challenge in collecting these measurements as it is difficult or impossible to separate them from the true model emission signal. This paper implements a method to quantitatively separate the reflections from the emission using polarization theory. Samples with a range of emissivities were tested, and in all samples the reflections were significantly reduced. This method will lead to more accurate radiometric and thermographic measurements in wind tunnel experiments.

Infrared↗
NASA NTRSDate not supplied

Infrared Reflection Removal in Wind Tunnels using Polarization Theory

Infrared radiometry with infrared cameras allows for high spatial resolution, noncontact measurements in wind tunnel experiments and has been increasingly used to visualize flow features. Reflections from test section walls present a major challenge in collecting these measurements as it is difficult or impossible to separate them from the true model emission signal. This paper implements a method to quantitatively separate the reflections from the emission using polarization theory. Samples with a range of emissivities were tested, and in all samples the reflections were significantly reduced. This method will lead to more accurate radiometric and thermographic measurements in wind tunnel experiments.

Infrared↗
NASA NTRSDate not supplied

Implementation of the Lifetime Method in uPSP Measurements

At NASA Ames Research Center, unsteady pressure-sensitive paint (uPSP) measurements are obtained using the ‘intensity method’ which measures paint luminescence in response to a continuous, constant excitation. These measurements are obtained using high-speed cameras and are processed into fluctuating components of pressure. However, the nature of the intensity method also requires a separate steady state (time mean) pressure measurement to be obtained. This steady state measurement has typically been obtained using a separate set of PSP equipment that uses the ‘lifetime method’, which uses pulsed excitation to measure paint decay lifetime. If the lifetime method were implemented in the high-speed uPSP system, both the fluctuating and mean components of pressure could be obtained with a single system. This would greatly streamline setup, operations, and processing. In this paper, we describe work performed at the Fluid Mechanics Laboratory at NASA Ames to implement the lifetime method in our uPSP system. The uPSP acquisition system uses Phantom v2512 high-speed cameras, and it was initially uncertain if results of adequate quality could be obtained - their high framerate comes at the cost of several undesirable characteristics, which are explored in this paper. It was also uncertain if illumination using LED lamps, rather than a stronger source such as lasers, would be adequate. The data acquisition and data processing are discussed and the results analyzed. It was found that satisfactory lifetime method results can indeed be obtained using these high-speed cameras and LED lamps. This will allow the uPSP system to be greatly simplified and will have a large operational impact on how uPSP data is acquired in future wind tunnel tests.

Pressure Sensitive Paint↗
NASA NTRSDate not supplied

Camera Setup for Unsteady Pressure Sensitive Paint at NASA Ames Research Center

The unsteady Pressure-Sensitive Paint Development Team at NASA Ames Research Center is conducting a Launch Vehicle Demo Test in the Unitary Plan Wind Tunnel’s 11-ft Transonic Wind Tunnel in the first half of 2024 to showcase improvements made to unsteady Pressure-Sensitive Paint technology. The unsteady Pressure-Sensitive Paint setup has upgraded from a four-camera system to an eight-camera system, prompting analysis to maximize the system performance and overall data quality. Additional analysis was performed to maximize the system resolving power when subject to test constraints such as model size and model tunnel positions. These analyses have uncovered new opportunities to improve the unsteady Pressure-Sensitive Paint technology and will allow the system to collect higher quality data with simple changes to the setup procedure.

Camera Calibration↗
NASA NTRSDate not supplied

NASA’s Unsteady Pressure-Sensitive Paint Phase I Development Overview

Since 2019, a group out of NASA Ames Research Center(ARC)has been focused on implementing systematic updates to make unsteady pressure-sensitive paint (uPSP) a more viable capability for production wind tunnel testing. Focusing on the general categories of data acquisition, data transfer, data processing, and data visualization, the uPSP Development Team has made several improvements to increase data quality and innovate a more workable system that would provide valuable surface pressure data to customers. As a result of the COVID-19 pandemic and several initial demonstration tests prior to the formal start of the development effort, the decision was made to focus on launch vehicles as the test article. To-date this development has focused on implementation in the ARC Unitary Plan Wind Tunnel 11-by11-footTransonic Wind Tunnel due to the large optical access of the test section and that the NASA Advanced Supercomputer is located at ARC. This paper summarizes the project origins and the results of four years of development effort, which will all culminate in a final demonstration test in the first half of2024.

unsteady pressure-sensitive paint↗
NASA NTRSDate not supplied

Spectral Proper Orthogonal Decomposition of uPSP Measurements in Recent NASA Ames Wind Tunnel Test

This paper discusses Spectral Proper Orthogonal Decomposition (SPOD) of the Unsteady Pressure-Sensitive Paint (uPSP) measurements in recent NASA Ames wind tunnel test. The uPSP measurements were collected using Innovative Scientific Solutions, Inc. (ISSI) Porous, Fast-Response Pressure-Sensitive Paint (FP-XXX), 40 ISSI four-inch air-cooled Light-Emitting Diodes (LEDs), and 8 Phantom v2512 high-speed cameras at 10,000 frames per second in the Launch Vehicle Demo Test (LVDT) of the Space Launch System (SLS) Block 1B crew vehicle in the 11-by 11-foot transonic test section of the Unitary Plan Wind Tunnel (UPWT) at NASA Ames Research Center in April 2024. Fig. 1 shows the scale model of the SLS launch vehicle installed in the wind tunnel during the test.

Aeroacoustics↗
NASA NTRSDate not supplied

Spectral Proper Orthogonal Decomposition of uPSP Measurements in Recent NASA Ames Wind Tunnel Test

This paper discusses Spectral Proper Orthogonal Decomposition (SPOD) of the Unsteady Pressure-Sensitive Paint (uPSP) measurements in recent NASA Ames wind tunnel test. The uPSP measurements were collected using Innovative Scientific Solutions, Inc. (ISSI) porous, fast-response pressure-sensitive paint, 40 ISSI four-inch air-cooled Light-Emitting Diodes, and 8 Phantom v2512 high-speed cameras at 10,000 frames per second in the uPSP Launch Vehicle Demonstration Test (LVDT) of the Space Launch System (SLS) vehicle in the 11-by 11-foot transonic test section of the Unitary Plan Wind Tunnel at NASA Ames Research Center in April 2024. SPOD is derived from a space-time proper orthogonal decomposition problem for statistically stationary flows. SPOD modes are determined in the frequency domain. Each SPOD mode oscillates at a single frequency. SPOD can be viewed as an extension of the Discrete Fourier Transform composition and the Dynamic Mode Decomposition. In this paper, the outputs of SPOD of the uPSP measurements in the uPSP LVDT are presented and the effectiveness of SPOD in the identification, diagnosis and analysis of the aerodynamic and aeroacoustic phenomena is demonstrated. The unsteady and dynamic property of the pressure field on the surface of the SLS Block 1B crew vehicle is presented with the visualization of the SPOD modes of the uPSP measurements in the tests of a Mach sweep run of the uPSP LVDT. The SPOD outputs were generated with the execution in parallel of a code in Python, with the library of Message Passing Interface for parallel processing, on the NASA Pleiades supercomputer. The work described in this paper is a part of NASA’s development of a new state-of-the-art uPSP capability in production wind tunnels. Funding was provided by the NASA Aerosciences Evaluation and Test Capabilities Portfolio Office.

Aeroacoustics↗
NASA NTRSDate not supplied

Spatiotemporal Analysis of High-Resolution Pressure-Sensitive Paint Measurements on a Launch Vehicle Wind Tunnel Model

An accurate understanding of unsteady aerodynamic loads is critical for launch vehicle structural design and for development of the vibro-acoustic environment for payload components. Analysts commonly use point-wise surface pressure measurements from wind tunnel testing to build statistical models of the in-flight turbulent boundary layer flow structures, often extrapolating over large swaths of the surface due to measurement sparsity. We present novel results from a transonic wind tunnel test using fast-response pressure-sensitive paint (PSP) and show how it can be used to visualize and quantify localized turbulent boundary layer wall pressure statistics with unprecedented spatial resolution. The wind tunnel model is a scaled model of the Space Launch System (SLS) rocket Block 1B Crew configuration and analysis focused on the compression corner between the Service Module fairing and the Universal Stage Adapter.

Corcos Model↗
NASA NTRSDate not supplied

Steady Surface Pressure Measurement via the Lifetime Method With High-Speed Cameras in NASA's Unitary Plan Wind Tunnel

High spatial resolution measurement of steady surface pressure via pressure-sensitive paint at NASA Ames has traditionally relied on specialized cameras equipped to accumulate charge over multiple exposures, whereas measurement of the fluctuating component of pressure uses an altogether separate set of high-speed cameras. To reduce complexity of installation, data acquisition, and processing, we have implemented methods to use a single set of commercial off-the-shelf cameras to produce both steady and unsteady pressure measurements. Both imaging systems were installed in the 11-by 11-foot NASA Ames Unitary Plan Wind Tunnel and acquired images of a scaled model of the Space Launch System Block 1B Crew and Cargo configurations over a variety of flow conditions. This work focuses on methods for data acquisition, processing, and calibration to produce steady-state pressure estimates on the surface of the wind tunnel model based on the lifetime method. It will then compare the steady solutions produced by the legacy and high-speed imaging systems.

Pressure Sensitive Paint↗
NASA NTRSDate not supplied

Invited: uPSP Launch Vehicle Demonstration Test at NASA Ames Research Center

The Unsteady Pressure-Sensitive Paint (uPSP) Development Team outof NASA Ames Research Center (ARC) has spent the past five yearsimproving the systems and processes to advance the uPSP technology for production-level wind tunnel testing. Already considered turnkey for small-scale and research applications, development in acquisition, calibration, data transfer, and data processing were needed to be useful to customers testing at NASA wind tunnels. This development focused at ARC at the Unitary Plan Wind Tunnel (UPWT) 11-by 11-ft Transonic Wind Tunnel due to the large optical access of the test section and the NASA Advanced Supercomputer(NAS), also located at ARC. A Launch Vehicle Demonstration Test (LVDT) at the UPWT represents a milestone of this initial phase of development where several new improvements were demonstrated in a production wind tunnel environment for the first time. LVDT was conducted in April 2024 and used a 4% forebody Space Launch System (SLS) Block 1B model as the test article. Both a crew and cargo configuration were tested, with varying Mach numbers, pressures, model positions, and camera magnifications. This paper summarizes the details of the test and is part of a collection with four additional papers that provide greater detail on: high-speed lifetime methodology, spectral proper orthogonal decomposition analysis, quality of high-resolution data compared to Corcos model, and data quality, calibration, and uncertainty.

SLS↗