Engineering topics
Publications and source records attributed to E. Venkatapathy.
This paper seeks to inform of the need for, and approaches to, sustaining critical thermal protection systems (TPS) for in-situ planetary missions in the coming decade. The key technologies, HEEET and PICA, are needed only for these NASA missions, will not be sustained in the absence of use, and are at risk of atrophy in the absence of mitigation.
Several international Venus missions, both orbiter, and in-situ probe are in the works after a prolonged absence. Future missions are expected to be long-duration lander missions and balloon missions to investigate the cloud layer. The entry mass for these in-situ missions will be significantly higher, and the aeroshell will be larger, than previous missions. Two cardinal requirements govern the selection and use of thermal protection systems (TPS), namely, robustness to assure mission safety during entry and mass efficiency so that the useful mass for science is maximized. One cannot trade mission safety for mass when it comes to TPS. The robustness of the TPS is a paramount requirement as it is a single point of system failure. At the same time, TPS mass is carried for the entire mission duration prior to entry, and any excess TPS mass is at the cost of science payload. Future missions will benefit enormously from TPS options with mass and performance benefits far beyond advanced carbon-carbon (ACC) that is currently proposed for the DAVINCI mission. NASA STMD, and SMD jointly invested in the development of 3-D woven thermal protection systems in the last decade, and as a result, the Heat-shield for Extreme Entry Environment Technology (HEEET) TPS has been matured to TRL 6. It is ready for future mission use including Venus. The HEEET project focused on developing a broad technology base, applicable for missions not only to Venus, but also to Saturn, the Ice Giants, and higher speed sample return missions such as Mars Sample Return requiring extreme robustness due to bio-hazards. The dual-layer HEEET (DL-HEEET) is proven to be extremely robust. DL-HEEET performed well in arc jet and laser testing conditions where heritage carbon-phenolic failed. HEEET also proved to be more mass efficient compared to Carbon-Phenolic. Recently, the principal author was invited to present his perspectives to the 2023-2032 Planetary Sciences Decadal Venus subcommittee on the current state of TPS for future Venus missions [1]. In addition to pointing out successful TPS and other developments in the last decade in support of entry systems, the principal author made two findings: 1) importance of and need to sustain TPS capabilities that took nearly a decade to develop and 2) the opportunity to further optimize TPS mass without sacrificing robustness to further enable future in-situ missions. This talk will focus on the above two recommendations and provide the rationale for them. The intent of the talk is to seek advocacy from the VEXAG community for the criticality of TPS sustainment and the benefits of 3D woven TPS optimization. TPS Capability Sustainment: HEEET development was necessitated by the atrophy of heritage carbon-phenolic. Atrophy has impacted other TPS materials as well. Avcoat, the TPS that successfully allowed astronauts to explore the Moon in the 1960s and 70s, took nearly a decade and $10’sM to recover in support of Orion/Artemis. One of the most used TPS materials, SLA 561V, had to be recovered prior to its use on Mars Pathfinder. Phenolic Impregnated Carbon Ablator (PICA), the TPS that replaced SLA 561V on MSL, has undergone multiple replacements and recovery due to constituent rayon changes. Recently, NASA invested in a domestic rayon replacement program and also invested in FMI to consolidate PICA capability for NASA missions, as a result of FMI’s decision to discontinue commercial FiberForm, which is needed for PICA. TPS used for planetary missions are unique and have no other commercial or defense use. In addition, low mission cadence is also a driver for TPS atrophy. Hence, NASA, as the steward, must take steps to ensure and sustain TPS capabilities. In this talk, we outline steps NASA can take to keep abreast of emerging risks and target risk mitigation steps to ensure TPS capability sustainment for Venus and other extreme environment missions. Next Generation of Mass efficient and Robust TPS: NASA invested in an alternate TPS to PICA based on felt-technology called Conformal-PICA which has the potential to save 30% - 50% mass over PICA. The development was discontinued at a Technology Readiness Level (TRL) of ~ 5. 3D Mid-Density Carbon Phenolic (3MDCP) is a single layer variant of HEEET, based on the insulating layer only (SL-HEEET) and currently baselined for the Mars Sample Return Mission Earth Entry System due to its mass efficiency (30% more mass efficient than DL- HEEET). Currently, SL-HEEET is limited to aeroshell diameters of < 1.3m. The SL-HEEET was compared to DL-HEEET in the recent ADVENT flag-ship class mission study in support of the Planetary Science Decadal. SL HEEET was the recommended TPS based on 30% mass savings for both the balloon and lander missions. Given C-PICA and SL-HEEET have superior reliability and mass efficiency, advocacy from VEXAG is sought for completing their further development to TRL 5/6 in this decade so as to enable TPS readiness for future missions.
The Decadal Survey report released [1] prioritizes Uranus as the highest priority Flagship class mission to be explored with an orbiter and a probe and it also recommended Saturn Probe under New Frontiers mission class. Thermal protection system (TPS) is essential for Uranus and Saturn probe missions. The two cardinal requirements are that it must be fail-safe and yet be mass efficient. The Decadal Survey report also pointed out the readiness of heatshield for extreme entry environment technology (HEEET) at TRL 6 for probe missions at Gas Giants. HEEET relies on 3-D weaving and is shown to be a robust and mass efficient TPS through ground testing and analysis. HEEET was matured to TRL 6 in 2019. HEEET was reported at the Ice Giant Workshop in 2019 at Marseille. Since 2019, significant advances have been made primarily because of Mars Sample Return (MSR) mission. MSR baselined 3-D Woven TPS as its heatshield for the earth entry system. MSR earth entry system (EES) requirements and the resulting heatshield/TPS requirements are most stringent of all entry missions. This is a result of backward contamination protection which classifies MSR as a “restricted class 5” mission to safeguard the accidental release of potentially hazardous Mars Sample into Earth’s atmosphere. Complex requirements for the heatshield start with micro-meteor impact tolerance followed by the requirement for steep entry to minimize the size of the impact footprint which results in extreme heating. The heatshield is part of the impact attenuation system. The EES architecture does not use a parachute and is designed to tolerate impact loads. Hence heatshield TPS selection and design becomes one of the key challenges. After completion of the HEEET technology maturation in 2019, IRAD efforts focused on assessing the 3-D Woven family of TPS to MSR EES. After nearly two years of evaluation of alternate TPS such as carbon phenolic, C-C hot structure, PICA, and 3-D woven family of TPS, a single layer 3-D woven TPS derived from the dual-layer HEEET was down selected and is currently the baseline. A new loom capable of weaving the single-layer 3-D woven preform at 80” wide has been designed, assembled and is currently on the verge of weaving the MSR EES TPS. During the HEEET maturation and the follow-on development, the single-layer TPS has been tested at extreme heating conditions. As a result, single layer TPS was recommended and evaluated during the Planetary Mission Concept Studies funded by NASA in preparation for the Decadal committee. In addition, in anticipation of Saturn mission proposals, single layer was evaluated as well. Aerocapture can reduce the trip time, also allow bigger payload fraction and in addition, it allows for the possibility of probe delivery once the spacecraft is in orbit. This can lead to obtaining both in-situ data as well as data from orbit simultaneously. Since Aerocapture depletes energy/velocity, probe delivery from orbit reduces the demand on TPS. Aerocapture was mentioned in the Decadal Study report as ready for implementation, but due to perceived risk it is not adopted by the mission designers. Establishing TPS readiness for aerocapture missions will be addressed. Going one step beyond aerocapture is aerogravity assist if fast return is the goal. Recent studies [4] looked at aerogravity assist and the TPS readiness. This talk will highlight both aerocapture and aerogravity assist from a TPS perspective. The main objective of this proposed talk is to present a comprehensive picture of the SOA TPS technology including recent developments. The talk will highlight advances in manufacturing, results from the Decadal White Papers, PMCS and other studies, and aerocapture and aerogravity assist that could play a role in the near or far term in-situ exploration.
- The Mars Sample Return Earth Entry System is being designed to withstand entry environments of: - Peak Heat Flux of > 3000 W/cm2 - Peak Dynamic Pressure of > 2 atmospheres - Peak Shear of > 3000 Pa. - The TPS Material System Selected to support MSR EES is “3MDCP”, 3D Mid Density Carbon Phenolic. 3MDCP is a derivative of the HEEET material system, using the “Insulation Layer” only. - Implementation of 3MDCP on EES is monolithic instead of a tile architecture in order to meet MSR reliability demands. - The EES TPS Team has recently completed a number of major engineering development milestones in support of delivering the flight 3MDCP TPS hardware: - Weaving Scale-Up completed, > 80” width woven preform production underway - Full Scale Forming & Manufacturing Attrition completed to verify delivered thickness capabilities. - Recent Design Change: EES design has been changed from a 45 degree sphere cone to a 52.5 degree sphere cone to allow for additional system mass.
Nephele is a Venus atmospheric descent probe concept designed to analyze cloud, haze, and dust particles. It combines a unique set of technologies (Figure 1): recently developed thermal protection materials (3D-CC and HEEET), aerosol sampling technologies with heritage in both planetary and airborne science (high-speed inlets and particle separation), and rapid, robust optical analysis instruments (such as the VOLTR dual spectrometer). Nephele is designed to be complentary to other efforts such as DAVINCI and Venera-D, which target Venus atmospheric gas analysis, by specifically targeting cloud and haze particles.
Aerosols (clouds, hazes, dusts) are drivers of key planetary processes, including mass and energy transfer; planetary climate evolution, as in the divergence of Venus and Earth; and are even of habitability interest, as Earth’s fog and cloud water have a substantial microbial presence. However, aerosols are highly dynamic, and once-in-a-lifetime flagship missions are not enough to fully characterize them. AERACEPT (AErosol Rapid Analysis Combined Entry Probe/sonde Technology) is an early-stage (TRL 2-3) technology combining the functions of an entry vehicle and aerosol-sampling passive descent sonde into a single aeroshell body. It is designed to reduce the mass, volume, and complexity of planetary aerosol science to within a small spacecraft footprint, allowing more frequent or concurrent missions. It is particularly well suited for a Venus mission, where the particles of greatest interest are within the subsonic descent regime, and is included in the Nephele mission concept study for a small spacecraft targeting Venus cloud and haze particles between 60 and 47 km.