Search NASA⌕ Search

Engineering topics

Edgell, D. H.

Publications and source records attributed to Edgell, D. H..

At least 37 records · Page 2

Comparison of Shadowgraphy and X-Ray Phase Contrast Methods for Characterizing a DT Ice Layer in an Inertial Confinement Fusion Target

Shadowgraphy and x-ray phase contrast (XPC) imaging are two techniques that are used for characterizing the deuterium-tritium ice layer in Inertial Confinement Fusion targets. Each technique has limitations that affect how accurately they can characterize small crystalline defects and measure the ice-thickness non-uniformities that may be only a few micrometers in height. The concern is that shadowgraphy may be overly sensitive to the shape and depth of defects in the surface and insufficiently sensitive to the shape of longer-wavelength roughness, while x-ray phase contrast may be too insensitive to defects in the ice surface. Multiple ice layers with different thicknesses (40 to 63 μm), thickness uniformities (peak-valley variations that range from <2- to 12 μm), and crystal defects were analyzed using shadowgraphy and x-ray phase contrast techniques. The results from each method agree when the ice layer is uniformly thick and the crystal lacks defects. That agreement worsens as the number of defects in the surface of the ice layer increases and the roughness that is determined from a shadowgram image of the target’s limb is greater than can be justified by the number of defects that are seen in the target’s front and rear surfaces. The XPC technique is considerably less sensitive to surface defects, in part due to the poorer dynamic range and image resolution compared to shadowgraphy. Localized regions of the ice layer that are thicker or thinner than the average thickness of the layer are reported by shadowgraphy to be smaller in height and footprint (by up to 30%) than by XPC. As a result, the two techniques report different ice layer thicknesses that can vary by up to 10%. Shadowgraphy results from two caustics that trace different paths through the target, and, in theory, image the same ice-vapor surface (but reflect from either the vapor or ice side of the interface) did not consistently characterize the size or shape of ice features to be the same magnitude. Here, the XPC technique provides the best assessment of low-mode (l < 7) roughness in the ice layer. Shadowgraphy results using the strongest caustic is best for detecting the presence of grooves in the ice, though not for quantifying the size of them. If multiple grooves are present it is best to discard and reform the ice layer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Validation of heat transport modeling using directly driven beryllium spheres

Recent experiments involving directly driven beryllium spheres are reported. Plasma conditions are measured using Thomson scattering with the probe beam pointed 200, 300, and 400 μ m from the surface of the sphere. Laser coupling is assessed using calorimeters that collect scattered light placed at various locations within the target chamber. Laser intensities of 1 0 14 W / c m 2 and 2.5 × 1 0 14 W / c m 2 are chosen to minimize unmodeled laser-plasma interactions (LPIs) that lead to laser-target decoupling. Two-dimensional simulations are compared to the interpreted data using the radiation-hydrodynamics code Lasnex. Heat transport is simulated using flux-limited Spitzer–Harm with both high ( f = 0.15) and low ( f = 0.03) flux limiters and the Schurtz–Nicolai-Busquet (SNB) model. At 1 0 14 W / c m 2 , all three heat transport models agree well with the measurement, demonstrating that the heat flux is local at low intensities near the measurement locations. At 2.5 × 1 0 14 W / c m 2 , the SNB and high flux model roughly match the plasma conditions but predict 2% uncoupled light compared to 10% measured. Additionally, the use of drive multipliers to match the measured coupled light does not alter the agreement between measured and simulated plasma conditions, suggesting that decoupling due to LPI is unlikely to alter this agreement. The low flux model cannot match the plasma conditions and results in 19% scattered light. The use of a resonant absorption model can be used to bring the simulated scattered light into agreement, but the simulated plasma conditions are still in disagreement with the measurement. For this reason, the low flux model is rejected.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Anomalous Absorption by the Two-Plasmon Decay Instability

Radiation-hydrodynamic simulations of directly driven fusion experiments at the Omega Laser Facility predict absorption accurately when targets are driven at low overlapped laser intensity. Discrepancies appear at increased intensity, however, with higher-than-expected laser absorption on target. Strong correlations with signatures of the two-plasmon decay (TPD) instability—including half-harmonic and hard-x-ray emission—indicate that TPD is responsible for this anomalous absorption. Scattered light data suggest that up to ≈ 30 % of the laser power reaching quarter-critical density can be absorbed locally when the TPD threshold is exceeded. A scaling of absorption versus TPD threshold parameter was empirically determined and validated using the laser–plasma simulation environment code.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Development of a directly driven multi-shell platform: Laser drive energetics

Simulations predict that directly driven multi-shell targets can provide a robust alternative to conventional high-convergence implosion concepts by coupling two to three times more energy into the final igniting thermonuclear fuel assembly than indirect-drive concepts. The three-shell directly driven Revolver concept [K. Molvig, M. J. Schmitt, B. J. Albright, E.S. Dodd, N.M. Hoffman, G.H. McCall, and S.D. Ramsey, Phys. Rev. Lett. 116, 255003 (2016)] utilizes a design that maximizes laser energy conversion into inward kinetic energy of the outermost ablator shell (~9%) while minimizing the DT fuel convergence (~9) to reduce the mixing of material from the innermost shell into the fuel. Inherent in this design concept is the use of 192 narrow beams (with a 1/e laser beam-to-capsule diameter ratio of 0.33) from the National Ignition Facility laser pointed in a polar direct drive laser configuration. In this paper, we demonstrate that low average laser intensity at the capsule surface (≤300 TW/cm 2 ) limits the measured laser backscatter, indicating that a greater amount of laser energy is coupled into the target. Omega experiments have been performed to determine the coupling of laser energy to the outermost shell of a scaled Revolver target (i.e., the ablator shell) by measuring capsule implosion trajectories and scattered-light fractions for two different drive configurations. Comparisons of simulated shell trajectory and velocity profiles with experimental data obtained from self-emission images show good agreement and are consistent with measured scattered light data. Furthermore, the low levels of scattered light measured are consistent with post-shot simulation results that show high hydro-coupling efficiency. These results strengthen the case for using narrow beams at low intensity to drive large ablator capsules for future direct-drive, multi-shell ignition concepts.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tripled yield in direct-drive laser fusion through statistical modelling

Accurate predictive models are essential to the design of high-performance, laser-fusion experiments. Here, we report the development of a promising statistical approach that has been used to quantitatively predict and design several cryogenic deuterium-tritium (DT) implosions on the OMEGA Laser System, leading to the tripling of the fusion yield to its highest value for direct-drive laser fusion of DT-layered targets. When scaled to National Ignition Facility laser energies of 1.9 MJ, these targets are predicted to produce a fusion energy output of ~500 kJ—several times larger than current fusion yields achieved at that facility. Future applications of this approach will guide the exploration of the vast parameter space for the conditions required for thermonuclear ignition and expose gaps in our understanding of laser-fusion physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulated refraction-enhanced X-ray radiography of laser-driven shocks

Refraction-enhanced x-ray radiography (REXR) is used to infer shock-wave positions of more than one shock wave, launched by a multiple-picket pulse in a planar plastic foil. This includes locating shock waves before the shocks merge, during the early time and the main drive of the laser pulse that is not possible with the velocity interferometer system for any reflector. Simulations presented in this paper of REXR show that it is necessary to incorporate refraction and attenuation of x rays along with the appropriate opacity and refractive-index tables to interpret experimental images. Simulated REXR shows good agreement with an experiment done on the OMEGA laser facility to image a shock wave. REXR can be applied to design multiple-picket pulses with a better understanding of the shock locations. Finally, this will be beneficial to obtain the required adiabats for inertial confinement fusion implosions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Tripled yield in direct-drive laser fusion through statistical modelling [Tripling the yield in direct-drive laser fusion via predictive statistical modeling]

Focusing laser light onto a very small target can produce the conditions for laboratory-scale nuclear fusion of hydrogen isotopes. The lack of accurate predictive models, which are essential for the design of high-performance laser-fusion experiments, is a major obstacle to achieving thermonuclear ignition. Here we report a statistical approach that was used to design and quantitatively predict the results of implosions of solid deuterium–tritium targets carried out with the 30-kilojoule OMEGA laser system, leading to tripling of the fusion yield to its highest value so far for direct-drive laser fusion. When scaled to the laser energies of the National Ignition Facility (1.9 megajoules), these targets are predicted to produce a fusion energy output of about 500 kilojoules—several times larger than the fusion yields currently achieved at that facility. As a result, this approach could guide the exploration of the vast parameter space of thermonuclear ignition conditions and enhance our understanding of laser-fusion physics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The National Direct-Drive Inertial Confinement Fusion Program

The National Direct-Drive Inertial Confinement Fusion Program consists of the 100-Gbar Campaign on the 30-kJ, 351-nm, 60-beam OMEGA Laser System and the Megajoule Direct-Drive (MJDD) Campaign on the 1.8-MJ, 351-nm, 192-beam National Ignition Facility (NIF). The main goals of the 100-Gbar Campaign are to demonstrate and understand the physics for hot-spot conditions and formation relevant for ignition at the MJ scale, while the MJDD Campaign seeks to understand the laser-plasma interactions, energy coupling, and laser imprint for ignition-scale direct-drive coronal plasmas. An overview of the multi-year, systematic effort that is underway for the National Direct-Drive Inertial Confinement Fusion Program (including laser, target, and diagnostic improvements in progress), as well as recent results from the 100-Gbar Campaign on OMEGA and the MJDD Campaign on NIF is presented in this paper.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Ray-based modeling of cross-beam energy transfer at caustics

Cross-beam energy transfer (CBET) is a laser-plasma instability that significantly impacts laser energy deposition in laser-driven inertial confinement fusion (ICF) experiments. Radiation-hydrodynamics simulations, which are used to design and tune ICF implosions, use ray-based CBET models, but existing models require artificial multipliers to conserve energy and to obtain quantitative agreement with experiments. The discretization of the ray trajectories in traditional ray-based CBET models does not account for the rapid variation in CBET gain as rays pass through caustics. In this study, we introduce a new model that allows one to treat caustics much more accurately and greatly improves energy conservation. The ray-based CBET calculations show excellent agreement with laser absorption from 2-D wave-based calculations (0.3% difference) and a 3-D 60-beam OMEGA implosion (2.4% difference) without artificial multipliers.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Unabsorbed light beamlets for diagnosing cross-beam energy transfer

Here, a new diagnostic has been fielded on OMEGA to diagnose cross-beam energy transfer (CBET) during direct-drive implosions. Unabsorbed light from each OMEGA laser beam is imaged as a distinct “spot” onto a gated optical imager. Each spot is in essence the end point of a beamlet of light that originates from different regions of each beam profile and follows a path determined by refraction. The intensity of light in the beamlet varies along its path as a result of absorption and CBET with other beamlets. This diagnostic allows the investigation of the effects of CBET on laser energy from specific locations of the beam profile. The diagnostic records images in two 200-ps time windows and includes a Wollaston prism to split each beamlet into two orthogonal polarizations recorded on separate images, allowing the absolute polarization of each beamlet to be determined. This diagnostic has provided the first evidence of polarization rotation caused by CBET during direct-drive implosions.

47 OTHER INSTRUMENTATION↗

Analysis of trends in experimental observables: Reconstruction of the implosion dynamics and implications for fusion yield extrapolation for direct-drive cryogenic targets on OMEGA

This paper describes a technique for identifying trends in performance degradation for inertial con finement fusion implosion experiments. It is based on reconstruction of the implosion core with a combination of low- and mid-mode asymmetries. This technique was applied to an ensemble of hydro-equivalent deuterium-tritium implosions on OMEGA that achieved inferred hot-spot pressures ≈56 ± 7 Gbar [S. Regan et al., Phys. Rev. Lett. 117, 025001 (2016)]. All the experimental observables pertaining to the core could be reconstructed simultaneously with the same combination of low and mid modes. This suggests that in addition to low modes, that can cause a degradation of the stagnation pressure, mid modes are present that reduce the size of the neutron and x-ray producing volume. The systematic analysis shows that asymmetries can cause an overestimation of the total areal density in these implosions. Finally, it is also found that an improvement in implosion symmetry resulting from correction of either the systematic mid or low modes would result in an increase of the hot-spot pressure from 56 Gbar to ≈ 80 Gbar and could produce a burning plasma when the implosion core is extrapolated to an equivalent 1.9 MJ symmetric direct illumination [A. Bose et al., Phys. Rev. E 94, 011201(R) (2016)].

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Subpercent-Scale Control of 3D Low Modes of Targets Imploded in Direct-Drive Configuration on OMEGA

In a series of direct-drive implosions on OMEGA, multiple time resolved x-ray images were used to tomographically measure their 3-D modes 1, 2, and 3 at a convergence ratio of ~3. Results show that the target modes vary linearly with the laser modes and are not affected by the Rayleigh–Taylor growth or lateral heat transport. This indicates that the residual modes (resulting from physical effects including beam mistiming, mispointing, and laser energy calibration) are approximately constant between shots. Lastly, this demonstrates that the low-mode amplitudes can be mitigated within by adjusting the laser-energy balance to compensate the residual target modes.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The National Direct-Drive Program: OMEGA to the National Ignition Facility

The goal of the National Direct-Drive Program is to demonstrate and understand the physics of laser direct drive (LDD). Efforts are underway on OMEGA for the 100-Gbar Campaign to demonstrate and understand the physics for hot-spot conditions and formation relevant for ignition at the 1-MJ scale, and at the National Ignition Facility to develop an understanding of the direct-drive physics at long scale lengths for the MJ Direct-Drive Campaign. For this paper the strategy of the National Direct-Drive Program is described; the requirements for the DT cryogenic fill-tube target being developed for OMEGA are presented; and preliminary LDD implosion measurements of hydrodynamic mixing seeded by laser imprint, the target-mounting stalk, and microscopic surface debris are reported.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Effect of Tritium-Induced Damage on Plastic Targets from High-Density DT Permeation

Direct-drive inertial fusion experiments conducted at the Laboratory for Laser Energetics implode 860-μm-diam, 8-μm-thick glow-discharge polymer (GDP) capsules that have a solid, uniform, 60- to 80-μm-thick layer of an equimolar mixture of deuterium and tritium (DT) on their interior. The DT is permeated through the capsule’s wall up to pressures of 1000 atm in small pressure steps to prevent buckling; this occurs over many hours. The capsule is then cooled, the DT is solidified, and the uniform layer is formed using thermal gradients produced by heat deposited from beta decay of the tritium. Thermal contraction of the capsule from cooling is expected to be ~1% of the diameter. Capsules permeated with DT do not exhibit this contraction and retain their room-temperature diameter after cooling. Sources of error in the imaging system were explored, and a systematic 3 μm over measurement of the diameter was revealed and corrected. However, both GDP capsules permeated with only deuterium and polystyrene capsules permeated with DT do exhibit thermal contraction. The highly cross-linked GDP shell is under compressive stress after fabrication and experiences bond breakage when exposed to high-density DT during permeation. It is speculated that some of this compressive stress is relieved during bond cleavage and the capsule’s wall swells, which counteracts contraction during cooling. In addition, mass spectrometry of the DT gas in the permeation system has revealed the presence of hydrocarbons and other carbon-containing species that increase with time, confirming the radio-degradation of the polymer.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Simulations and measurements of hot-electron generation driven by the multibeam two-plasmon-decay instability

We report that multiple-beam experiments relevant to direct-drive inertial confinement fusion show the importance of nonlinear saturation mechanisms in the common-wave two-plasmon-decay (TPD) instability. Planar target experiments on the OMEGA laser used hard-x-ray measurements to study the influence of the linear common-wave growth rate on TPD driven hot-electron production in two drive beam configurations and over a range of overlapped laser intensities from 3.6 to 15.2 x 10 14 W/cm 2 . The beam configuration with the larger linear common-wave growth rate had a lower intensity threshold for the onset of hot-electron production, but the linear growth rate did not have a significant impact on hot-electron production at high intensities. The experiments were modeled in 3-D using a hybrid code (LPSE) that combines a wave solver with a particle tracker to self-consistently calculate the electron velocity distribution and evolve electron Landau damping. Finally, good quantitative agreement was obtained between the simulated and measured hotel-electron distributions using a novel technique to account for macroscopic spatial and temporal variations that are present in the experiments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Full-wave and ray-based modeling of cross-beam energy transfer between laser beams with distributed phase plates and polarization smoothing

Radiation-hydrodynamic simulations of inertial confinement fusion (ICF) experiments rely on ray-based cross-beam energy transfer (CBET) models to calculate laser energy deposition. The ray-based models assume locally plane-wave laser beams and polarization averaged incoherence between laser speckles for beams with polarization smoothing. The impact of beam speckle and polarization smoothing on crossbeam energy transfer (CBET) are studied using the 3-D wave-based laser-plasma-interaction code LPSE . The results indicate that ray-based models under predict CBET when the assumption of spatially averaged longitudinal incoherence across the CBET interaction region is violated. A model for CBET between linearly-polarized speckled beams is presented that uses ray tracing to solve for the real speckle pattern of the unperturbed laser beams within the eikonal approximation and gives excellent agreement with the wavebased calculations. Lastly, OMEGA-scale 2-D LPSE calculations using ICF relevant plasma conditions suggest that the impact of beam speckle on laser absorption calculations in ICF implosions is small (< 1%).

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Mitigation of cross-beam energy transfer in symmetric implosions on OMEGA using wavelength detuning

The effects of frequency detuning laser beams in direct-drive symmetric implosions were investigated with a 3-D cross-beam energy transfer (CBET) model. Our model shows that interactions between beams with relative angles between 45° and 90° are most significant for CBET in OMEGA direct-drive implosions. There is no net exchange in power between beams but there is significant redistribution of power from the ingoing central portion of the beam profile to the outgoing edge as it is exiting the plasma, reducing the total absorbed power. Furthermore, redistribution of laser power because of CBET increases the root-mean-square (rms) absorption nonuniformity by an order of magnitude. CBET mitigation by shifting relative wavelengths of three groups of laser beams fed by each of the different beamlines was modeled. At an on-target wavelength shift of Δλ ~ 10 Å, the total laser absorption was maximized, and the rms absorption nonuniformity was near minimum. In order to completely decouple the three groups of beams from each other requires wavelength shifts Δλ > 30 Å.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

The role of hot spot mix in the low-foot and high-foot implosions on the NIF

Hydrodynamic mix of the ablator into the DT fuel layer and hot spot can be a critical performance limitation in inertial confinement fusion implosions. This mix results in increased radiation loss, cooling of the hot spot, and reduced neutron yield. To quantify the level of mix, we have developed a simple model that infers the level of contamination using the ratio of the measured x-ray emission to the neutron yield. The principal source for the performance limitation of the “low-foot” class of implosions appears to have been mix. As a result, lower convergence “high-foot” implosions are found to be less susceptible to mix, allowing velocities of >380 km/s to be achieved.

42 ENGINEERING↗