Engineering topics
Edmondson, P. D.
Publications and source records attributed to Edmondson, P. D..
Solid breeder material crystal structure evolution due to Li burn up–Loss of crystal stability
Solid breeder materials for fusion power plants are subjected to extreme conditions of radiation damage, high temperature and designed component burn-up. Here, the loss of lattice stability of Li 2 TiO 3 due to Li burn-up was investigated using first principles-based approaches to aid evaluation of upper limit of component lifetime. The lattice stability is analyzed using calculated phonon dispersion in the Li 2 TiO 3 supercell, while Li burn-up is modeled by the introduction of Li-vacancies. It has been determined that the studied ceramic can be structurally stable up to ~40% of Li atoms burn-up. At 50% burn-up, the negative frequency branch in the phonon dispersion spectrum appears indicating the loss of lattice dynamical stability. Moreover, the structure obtained by introduction of unstable frozen phonons with minima energy amplitude also results in a phonon dispersion with negative branches in the structure obtained. Therefore, the system completely loses stability when approximately half of Li atoms are consumed.
Phase instabilities in austenitic steels during particle bombardment at high and low dose rates
Disruption of phase stability by energetic particle bombardment is a major challenge in designing advanced radiation-tolerant alloys and ion beam processing of nanocomposites. Particularly, ballistic dissolution susceptibility of different solute nanocluster species in alloys is poorly understood. Here, low dose rate neutron irradiations were conducted on a Fe-Cr-Ni based austenitic steel in the BOR-60 reactor (9.4 × 10 -7 dpa/s, 318 °C) followed by accelerated dose rate ion irradiations at multiple temperatures ( 10 -3 dpa/s, 380 – 420 °C). Using atom probe tomography, the stability of radiation-enhanced Cu-rich and radiation-induced Ni-Si-Mn-rich nanoclusters was evaluated. During neutron irradiation, Cu-rich clusters nucleated with their core concentrations progressively increasing with dose, while Ni-Si-Mn-rich clusters formed and evolved into G-phase precipitates. Ion irradiations dramatically altered the nanoclusters. Cu-rich clusters were ballistically dissolved, but Ni-Si-Mn-rich clusters remained stable and coarsened with dose at 400 and 420 °C, highlighting that different nanocluster species in a single microstructure can have innately distinct ballistic dissolution susceptibilities. Solute-specific recoil rates were incorporated into the Heinig precipitate stability model, which shows that in addition to radiation-enhanced diffusion, recovery from ballistic dissolution depends on solute concentration gradient near cluster interfaces. Finally, the combined experimental-modeling study quantified the critical temperatures and damage rates where ballistic dissolution dominates for each cluster species.
Corrosion resistance of functionally graded TiN/Ti coatings for proton exchange membrane fuel cells
Bipolar Plates (BPP) are important components of proton exchange membrane fuel cell (PEMFC) stacks. In the development of innovative fuel cell designs, it is advantageous to use aluminum for these applications, however, this material lacks the necessary corrosion resistance. Since the performance of PEMFC stacks depends on BPP properties, in particular, corrosion resistance, depositing titanium nitride (TiN) thin films onto aluminum substrates may improve their efficiency and durability. Present work focuses on improving corrosion resistance and hydrophobicity of TiN/Ti by using N graded films deposited onto aluminum substrates (AA-1100) by grid-assisted magnetron sputtering (GAMS). Electrochemical impedance spectroscopy (EIS) with potentiodynamic and potentiostatic polarization are used to investigate the performance of the substrate/film system at room temperature and 70 oC, thus simulating a prototypic PEMFC electrolyte environment. Electrochemical test results showed that graded TiN films improved corrosion resistance when compared with both the homogeneous films and the AA1100 uncoated substrate. Furthermore, contact angle results reveal improved hydrophobicity for both homogeneous and graded TiN coatings when compared with the AA1100 substrate.