Search NASA⌕ Search

Engineering topics

Edwards, Danny J

Publications and source records attributed to Edwards, Danny J.

Multislice simulation of transmission electron microscopy imaging of helium bubbles in Fe

Formation of nanoscale helium (He) bubbles in reduced activation ferritic/martensitic steels may lead to degradation of mechanical properties of materials. Transmission electron microscopy (TEM) has been commonly used to image the Fresnel contrast of He bubbles using a defocus of 0.5 µm ~ 1 µm. This paper presents our study of multislice simulation of the size correlation between imaged Fresnel rings and the actual He bubbles. It was found that for bubbles equal to or larger than 3 nm in diameter, the imaged bubble size, represented by its inner diameter of the first dark Fresnel ring (Din) in under-focused imaging conditions, increases with increasing electron-beam incoherency, but decreases with increasing defocus. The electron-beam accelerating voltage, bubble size, bubble position, and TEM sample thickness were found to have no significant influence on the deviation of Din from the actual bubble size (D0). For bubbles equal to or smaller than 2 nm, however, Din/Do increases dramatically with increasing defocus when it is above a threshold defocus. It was also suggested by this study that He bubbles can be differentiated from argon (Ar) bubbles by contrast differences.

Yao, Bo↗

Hierarchical Microstructures in CZT

Advanced characterization tools, such as electron backscatter diffraction and transmitted IR microscopy, are being applied to study critical microstructural features and orientation relations in as-grown CZT crystals to aid in understanding the relation between structure and properties in radiation detectors. Even carefully prepared single crystals of CZT contain regions of slight misorientation, Te-particles, and dislocation networks that must be understood for more accurate models of detector response. This paper describes initial research at PNNL into the hierarchy of microstructures observed in CZT grown via the vertical gradient freeze or vertical Bridgman method at PNNL and WSU.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

MULTISLICE SIMULATION OF TRANSMISSION ELECTRON MICROSCOPY IMAGING OF HELIUM BUBBLES IN IRON

The objective of this task is to establish the size correlation between transmission electron microscopy (TEM) imaged helium (He) bubbles and the actual bubbles in an iron (Fe) matrix. SUMMARY The results of this simulation study show that the size of TEM imaged He bubbles, represented by the inner diameter of the first dark Fresnel ring under defocused condition (Din), deviated from the actual bubble size (Do). Din was found to be larger than Do when imaged with a highly incoherent electron beam, but smaller than Do if the beam is coherent. The deviation of Din from Do increases with increasing defocus. On the other hand, the electron beam accelerating voltage, bubble size, bubble position, and TEM sample thickness do not significantly affect the value of D0/Do. This study also suggests that He bubbles can be differentiated from argon (Ar) bubbles by differences in Fresnel contrast.

36 MATERIALS SCIENCE↗

Electrochemical, Structural and Surface Characterization of Nickel/Zirconia Solid Oxide Fuel Cell Anodes in Coal Gas Containing Antimony

The interaction of antimony with the nickel-zirconia solid oxide fuel cell (SOFC) anode has been investigated. Tests with both anode-supported and electrolyte-supported button cells were performed at 700 and 800oC in synthetic coal gas containing 10 ppb to 9 ppm antimony. Minor performance loss was observed immediately after Sb introduction to coal gas resulting in ca. 5 % power output drop. While no further degradation was observed during the following several hundred hours of testing, cells abruptly and irreversibly failed after 800-1500 hours depending on Sb concentration and test temperature. Antimony was found to interact strongly with nickel and result in extensive alteration phase formation, consistent with expectations based on thermodynamic properties. Nickel antimonide phases, NiSb and Ni5Sb2, were partially coalesced into large grains and eventually affected electronic percolation through the anode support. Initial degradation was attributed to diffusion of antimony to the active anode/electrolyte interface to form an adsorption layer.

01 COAL, LIGNITE, AND PEAT↗

Polarization-Induced Interfacial Reactions between Nickel and Selenium in Ni/Zirconia SOFC Anodes and Comparison with Sulfur Poisoning

Three distinctly different characteristic responses of a nickel/yttria-stabilized zirconia (Ni/YSZ) cermet anode to the presence of hydrogen selenide in synthetic coal gas were observed, depending on temperature (650-800oC), H2Se concentration (0-40 ppm), and especially on the extent of anodic polarization (0 to ~0.5 V). The first level of response was characterized by a rapid but modest decrease in power density to a new steady state, with no further degradation observed in tests up to 700 hours in duration. Mostly observed at high temperatures, low H2Se concentrations, and low anodic polarizations, this response level was similar to effects caused by the presence of H2S, but with slower onset and lower reversibility. Higher anodic polarization at a constant current could trigger a second level of response characterized by oscillatory behavior involving cycles of rapid performance loss followed by rapid recovery. Oscillations at the constant current density were accompanied by the appearance and disappearance of a new feature in the electrochemical impedance spectrum with a summit frequency of ~100 Hz. Oscillatory behavior ceased when the current density was lowered. Such behavior was not observed for cells operated at a constant potential of similar magnitude, though. A third level of response, irreversible cell failure, could be induced by further increases in anodic polarization, additionally favored by low temperature and high H2Se concentration. Post-test analyses of failed cells by electron microscopy revealed the extensive microstructural changes including the appearance of nickel oxide and nickel selenide alteration phases, only at the anode/electrolyte interface. From bulk thermochemical considerations the formation of nickel selenides could not be expected. Local chemical conditions created at the anode/electrolyte interface appear to be of overriding importance with respect to the extent of Ni/YSZ anode interactions with H2Se in coal gas.

01 COAL, LIGNITE, AND PEAT↗

Majorana DUSEL R&D Final Report

This report summarizes the work performed at PNNL under the project Majorana Neutrinoless Double Beta Decay DUSEL R&D over the period of FY07-FY09.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Interaction of coal-derived synthesis gas impurities with solid oxide fuel cell metallic components

Chromium-containing iron-based alloys Crofer22 APU and SS 441 and nickel-based alloy Inconel600, all commonly used in a solid oxide fuel cell (SOFC) stack as interconnect materials, heat exchanger and gas feeding pipes, were exposed at 700-850oC to a synthetic coal gas containing ≤2 ppm phosphine, arsine, sulfur and antimony. Samples were characterized by SEM/EDS and XRD to monitor the secondary phase formation. Exposure of ferritic stainless steels to P led to the formation of surface Cr-Mn-P-O and Fe-P-O compounds and increased temperatures accelerated the rate of interactions. Fewer interactions were observed after exposures to As and Sb. No sulfur containing compounds were found. Nickel-based alloy exhibited much stronger interactions with As and P in comparison with ferritic steels and the arsenic interactions were particularly strong. The difference between the iron- and nickel-based alloys is explained by the different chemistry and morphology of the scales grown on the alloy surfaces in coal gas. While P and As interactions with the metallic parts in the SOFC are likely to mitigate the nickel/zirconia anode poisoning, the other degradation mechanisms should be taken into consideration to avoid potential stack failures. Manganese spinels were found to be effective as phosphorus getters and could be used in coal gas cleanup.

01 COAL, LIGNITE, AND PEAT↗

SOFC Ohmic Resistance Reduction by HCl-Induced Removal of Manganese at the Anode/Electrolyte Interface

The ohmic resistance of anode-supported solid oxide fuel cells having a manganese-based cathode was lowered when operated in synthetic coal gas containing hydrogen chloride. This effect was not observed for cells with cathodes that did not contain manganese. Substantial amounts of Mn were found throughout the grain boundaries of the 8 mole% yttria-stabilized zirconia (8YSZ) electrolyte. Exposure to HCl partially removed Mn near the anode/electrolyte interface, presumably by volatilization as MnCl2(g). This work suggests that one of the underlying causes of higher than expected electrolyte resistance in anode-supported SOFCs is a lowering of the ionic conductivity of 8YSZ by incorporation of manganese.

01 COAL, LIGNITE, AND PEAT↗

Degradation Mechanisms of SOFC Anodes in Coal Gas Containing Phosphorus

The interaction of phosphorus in synthetic coal gas with the nickel-based anode of solid oxide fuel cells has been investigated. Tests with both anode-supported and electrolyte-supported button cells were performed at 700 to 800oC in synthetic coal gas containing 0.5 to 10 ppm phosphorus, introduced as phosphine. Two primary modes of degradation were observed. The most obvious was the formation of a series of bulk nickel phosphide phases, of which Ni3P, Ni5P2, Ni12P5 and Ni2P were identified. Phosphorus was essentially completely captured by the anode, forming a sharp boundary between converted and unconverted anode portions. These products partially coalesced into large grains, which eventually affected electronic percolation through the anode support. Thermodynamic calculations predict that formation of the first binary nickel phosphide phase is possible at sub-parts per billion concentrations in coal gas at temperatures relevant to fuel cell operation. A second mode of degradation is attributed to surface diffusion of phosphorus to the active anode/electrolyte interface to form an adsorption layer. Direct evidence for the presence of such an adsorption layer on nickel was obtained by surface spectroscopies on fracture surfaces. Further, cell performance losses were observed well before the entire anode was converted to bulk nickel phosphide. Impedance spectroscopy revealed that these losses were primarily due to growth in electrodic resistance, whereas large ohmic increases were visible when the entire anode was converted to nickel phosphide phases. The rate of resistance growth for anode-supported cells showed a very low dependence on phosphorus concentration, attributed to phosphorus activity control within the anode by bulk nickel phosphide products.

01 COAL, LIGNITE, AND PEAT↗

Microscopic Evaluation of Contaminants in Ultra-High Purity Copper

Copper is one of the very few elements having no relatively long-lived radioisotopes and which can be electrodeposited to ultra-high levels of purity. Next generation experiments probing neutrino properties and searching for direct evidence of Dark Matter require ultra-clean materials, such as copper, containing the smallest quantities obtainable of naturally occurring radioactive contaminants. Copper is also of interest in the material science field for applications requiring low-activity materials, such as in electronics and semi-conductors, an example of which is reduced alpha activity, low-fault integrated circuits. Determining the purity of the copper is of great interest, but even more important is establishing the location of any contamination and its dispersion within the bulk material. Co-deposition of contaminants during copper electrodeposition and its relationship to nucleation and growth processes were investigated using a variety of analytical methods including scanning electron microscopy (SEM), laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS), and secondary ionization mass spectrometry (SIMS).

copper↗

Preferential orientation of Te precipitates in melt-grown CZT

Cadmium zinc telluride (Cd1-xZnxTe or CZT) has proved to be a useful material for semiconductor gamma-ray spectrometers and other electro-optic devices. It is often grown Te-rich to optimize its electrical characteristics, but this off-stoichiometric growth leads to the formation of semimetallic Te precipitates in the semiconducting host crystal. These precipitates can impair device performance and their formation needs to be inhibited, if possible, during growth. Characterization of melt-grown CZT has shown that Te precipitates are often faceted. In this study, characterization of several particles of different shapes revealed that most of the Te precipitates were preferentially oriented with the {101}CZT||{-12-10}Te . A secondary orientation relationship was also observed as {11-1}CZT||{01-11}Te for one of the {111}CZT family of planes. One of the particles exhibited {110}CZT||{01-10}Te and {001}CZT||{0001}Te . Precipitates were often found on {111}CZT twin boundaries and, in these cases, it was possible to assign specific orientations with respect to the twin plane. The expected orientation of the {0001}-plane of Te aligned with the {111}-plane of CZT was not observed even though a good lattice match is predicted in ab initio models. Observations of strained and polycrystalline Te precipitates are also discussed with relevance to the ab initio model and to impacts on electronic properties.

36 MATERIALS SCIENCE↗