Engineering topics

Eegholm, Bente

Publications and source records attributed to Eegholm, Bente.

6 records

NASA NTRS2019

Optical System Design and Integration of the Global Ecosystem Dynamics Investigation Lidar

The Global Ecosystem Dynamics Investigation (GEDI) instrument was designed, built, and tested in-house at NASA’s Goddard Space Flight Center and launched to the International Space Station (ISS) on December 5, 2018. GEDI is a multi-beam waveform LiDAR (light detection and ranging) designed to measure the Earth’s global tree height and canopy density using 8 laser beam ground tracks separated by roughly 600 meters. Given the ground coverage required and the 2 year mission duration, a unique optical design solution was developed. GEDI generates 8 ground sampling tracks from 3 transmitter systems viewed by a single receiver telescope, all while maximizing system optical efficiency and transmitter to receiver boresight alignment margin. The GEDI optical design, key optical components, and system level integration and testing are presented here. GEDI began 2 years of science operations in March 2019 and so far, it is meeting all of its key optical performance requirements and is returning outstanding science.

Integration↗

NASA NTRS2012

JWST Near-Infrared Detector Degradation: Finding the Problem, Fixing the Problem, and Moving Forward

The James Webb Space Telescope (JWST) is the successor to the Hubble Space Telescope. JWST will be an infrared optimized telescope, with an approximately 6.5 m diameter primary mirror, that is located at the Sun-Earth L2 Lagrange point. Three of JWST's four science instruments use Teledyne HgCdTe HAWAII-2RG (H2RG) near infrared detector arrays. During 2010, the JWST Project noticed that a few of its 5 micron cutoff H2RG detectors were degrading during room temperature storage, and NASA chartered a "Detector Degradation Failure Review Board" (DD-FRB) to investigate. The DD-FRB determined that the root cause was a design flaw that allowed indium to interdiffuse with the gold contacts and migrate into the HgCdTe detector layer. Fortunately, Teledyne already had an improved design that eliminated this degradation mechanism. During early 2012, the improved H2RG design was qualified for flight and JWST began making additional H2RGs. In this article we present the two public DD-FRB "Executiye Summaries" that: (1) determined the root cause of the detector degradation and (2) defined tests to determine whether the existing detectors are qualified for flight. We supplement these with a brief introduction to H2RG detector arrays, and a discussion of how the JWST Project is using cryogenic storage to retard the degradation rate of the existing flight spare H2RGs.

Rauscher, Bernard J.↗

NASA NTRS2011

Measuring the In-Process Figure, Final Prescription, and System Alignment of Large Optics and Segmented Mirrors Using Lidar Metrology

The fabrication of large optics is traditionally a slow process, and fabrication capability is often limited by measurement capability. W hile techniques exist to measure mirror figure with nanometer precis ion, measurements of large-mirror prescription are typically limited to submillimeter accuracy. Using a lidar instrument enables one to measure the optical surface rough figure and prescription in virtuall y all phases of fabrication without moving the mirror from its polis hing setup. This technology improves the uncertainty of mirror presc ription measurement to the micron-regime.

Ohl, Raymond↗

NASA NTRS2011

Cryogenic Thermal Vacuum Testing with Remote Optical Metrology

Flexure Engineering was awarded an SBIR to research and develop technology needed to build a thermal vacuum chamber made to take laser radar metrology through a window. The XATF test is proof of concept for this, and demonstrated the need for such a chamber. XATF refers to two pieces of critical ground support equipment for NASA's JWST (James Webb Space Telescope) Integrated Science Instrument Module (ISIM), the ISIM Alignment Target Fixture (IATF) and the Master Alignment Target Fixture (MATF). These optical alignment assemblies require characterization while under cryogenic temperature. A thermal vacuum chamber equipped with a shroud cooled with gaseous and liquid nitrogen was used. An inner shroud was cooled with liquid helium to approximately 30K. The XATF assemblies were kinematically mounted and oriented inside the inner shroud such that the optical targets were visible from outside an optical window on one of the chamber ports. Laser radar and theodolite mounted outside the window took measurements of various optical targets. Two cold cycles were completed. A third cycle was aborted. Metrology was successfully taken. There were some problems with the helium system. The cryo pumps were turned off to reduce vibrations during metrology. Many new technologies and testing methods must be developed for JWST and future programs that will require precision measurements. These technologies will be applicable to other cold temperature applications, such as lunar missions and superconductors. Remote metrology technologies can also be applicable to testing in harsh environments. Facilities with remote metrology capability will be valuable.

Boyd, Guinevere↗

NASA NTRS2006

Exo-atmospheric telescopes for deep space optical communications

For deep space optical communications, optical telescopes located above the Earth's atmosphere would have significant performance advantages over telescopes mounted on the Earth's surface. Link outages due to could cover would be eliminated, atmospheric attenuation would be eliminated, and signal degradation due to stray light would be reduced.

orbiting optical terminal↗

NASA NTRS2006

Exo-atmospheric telescopes for Deep Space Optical Communications

For deep space optical communications, optical telescopes located above the Earth's atmosphere would have significant performance advantages over telescopes mounted on the Earth's surface. Link outages due to cloud cover would be eliminated, atmospheric attenuation would be eliminated, and signal degradation due to stray light would be reduced. A study has been conducted to compare various exo-atmospheric platforms for the Earth end of the optical link.

orbiting optical terminal↗