Search NASA⌕ Search

Engineering topics

Efe, Mert

Publications and source records attributed to Efe, Mert.

At least 19 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Aluminum bonded SmCo5 magnets with enhanced mechanical strength

Despite their versatility and easy manufacturability, polymer-bonded magnets find limited application due to their limited mechanical properties and temperature resistance. In this study, we developed mechanically robust, aluminum-bonded SmCo5 magnets by utilizing a low-temperature, shear-assisted friction consolidation technique. Bonded magnets with varying magnetic phase content were fabricated at processing temperature of 500°C, and their microstructures, magnetic, mechanical, and electrical properties were systematically investigated. The resulting bonded-magnets showed effective consolidation with nanocrystalline microstructures. Magnetic properties were found to be tunable through variations in binder phase content, with coercivity reaching values up to 15.3 kOe (1217.5 kA/m) and maximum magnetic energy product up to 3.6 MGOe (28.7 kJ/m3), which are comparable to other bonded magnets. Electrical resistivities were lower than the polymer-bonded magnets, but comparable to the sintered ones. We observed an average flexural strength of 223 MPa for 60 vol.% SmCo5/Al sample, which is nearly two times higher than the reported values for sintered and bonded Sm-Co magnets. Our research demonstrated an effective approach to fabricate metal-bonded permanent magnets with superior magnetic and mechanical properties potentially applicable for high temperature applications.

Poudel Chhetri, Tej Bahadur↗
DOE OSTI2026

Thermal Stability and Ion Irradiation Response of Refined Grained V – 4Cr – 4Ti

Since the 1960’s, there has been interest in V-4Cr-4Ti and similar alloys as candidates for low activation structural materials for advanced nuclear reactors. V-4Cr-4Ti was produced using arc melting and subsequently subjected to large strain extrusion machining to produce a multimodal microstructure largely composed of nanocrystalline and ultrafine grain sizes. In-situ thermal stability of the multimodal V-4Cr-4Ti to 800 °C shows the formation of vanadium carbides with negligible grain growth. In-situ dual-beam 16 KeV He+ and 1 MeV Kr2+ ion irradiation performed at 700 °C to a final dose of ~5 displacements per atom show the formation of small He cavities well distributed throughout the system, with preferential clustering at grain boundaries. This work provides insight into how the increased fraction of grain boundaries affect the simultaneous dual beam ion irradiation response of multimodal V – 4 wt.% Cr – 4 wt.% Ti at elevated temperatures. Analysis of the cavities reveal an areal density of 0.024±0.007 cavities/nm2 and swelling of 0.236% after the dual-beam ion irradiation. Nanoindentation shows a ~50% increase in hardening after the ion irradiation at 700 °C.

TEM↗
DOE OSTI2024

Tribological behavior of hybrid Aluminum-TiB 2 metal matrix composites for brake rotor applications

Here, this research investigates the feasibility of hybrid aluminum metal matrix composites (MMC) incorporating TiB 2 particles for brake rotor applications. The composites were produced by incorporating both in-situ, submicron-sized TiB 2 particles and regular micron-sized TiB 2 powders via stir and squeeze casting techniques into A206 aluminum alloy matrix. Systematic adjustments in the fractions of in-situ and ex-situ TiB 2 particles were conducted to evaluate their impact on wear behavior and mechanisms. Combination of both particle types allowed composites with up to 10 vol% of reinforcements. Composites with higher proportions of ex-situ particles demonstrated increased wear resistance compared to those solely composed of in-situ particles, control specimens without TiB 2 , and conventional cast iron counterparts. The lowest wear rate for the hybrid composites sliding against phenolic brake pads was 1.1 × 10 -5 mm 3 /Nm, signifying a 3-fold reduction relative to cast iron sliding against the same pads. Wear analysis elucidated distinctive mechanisms within the hybrid composites, characterized by mild fragmented abrasive wear, adhesive wear, and plastic deformation, accompanied by the formation of an intermixed tribo-oxide layer.

42 ENGINEERING↗
DOE OSTI2024

Aluminum/SmCo 5 composites for structural and magnetic applications

Metal-bonded magnetic composites (MBMCs) present a promising alternative to dense sintered magnets, particularly for intricate components. Compared to polymer-based bonded magnets, MBMCs have wider applicability in harsh environments. In this paper, we demonstrate a solid-state shear-based manufacturing technique to introduce localized magnetization into a paramagnetic aluminum matrix by embedding SmCo5 permanent magnet particles. Our magnetic composites display hard magnetic behavior with a coercivity of 13 kOe and a remanent magnetization of 4.32 emu/g. In addition to magnetization, we also report a 9% improvement in Young’s modulus. Despite the local temperature rise during processing, the magnetic phases didn’t decompose into unwanted phases, preserving the composite's hard magnetic properties. Creation of an interfacial metallurgical bond with the matrix ensured the suitability of the composites for structural applications. Our study investigates the mechanical, and functional properties of composites, paving the way for lightweight structural magnetic composites with a transformative potential in the aerospace, nuclear, and automotive applications. This work underscores the potential for further optimization and development to drive innovations in magnet and equipment design.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Crafting Multifunctional Materials with Tailored Mechanical and Magnetic Properties by Solid-State Non-equilibrium Processing

Aluminum matrix composites hold promise for creating lightweight structural components with multifunctional properties. Nonetheless, achieving desired magnetic or electrical characteristics without compromising their fundamental mechanical properties presents a significant challenge. Here, in this study, we explore mechanical stir-based extrusion as a solid-state metalworking technique to develop fine-grained microstructures and highly refined metallic composites. Our study focuses on creating a SmCo 5 -reinforced aluminum matrix composite using solid stir extrusion (SSE) and assessing its microstructure, mechanical, and magnetic properties through a comprehensive suite of characterization tools, including x-ray diffraction, electron microscopy, and magnetometry. Our findings reveal that incorporating a small amount (3.76 wt.%) of SmCo 5 phase in a non-heat-treatable, non-magnetic aluminum alloy via SSE yields a composite that exhibits good hard magnetic characteristics with a large coercivity (H ci = 13.5 kOe) and improved mechanical properties. This study underscores non-equilibrium processing via solid-state high-speed stirring as a compelling method for crafting multifunctional materials with tailored mechanical and magnetic properties.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Exceptional strength and wear resistance in an AA7075/TiB 2 composite fabricated via friction consolidation

The friction consolidation method successfully reinforced aluminum 7075 alloy (AA7075) with high-volume fractions (12 and 24 vol%) of titanium diboride (TiB 2 ) by high pressure and severe plastic deformation at elevated temperatures. The consolidated AMCs have a uniform dispersion of submicron- and micron-sized TiB 2 particles in the AA7075 matrix, with significant refinement of the matrix grain size and the particles. The addition of TiB 2 significantly increases hardness by up to 50 %, Young’s modulus by up to 62 %, and ultimate tensile strength by up to 28 % to 672 MPa, while reducing ductility by 80 %. Wear resistance of 7075/24 vol% TiB 2 improves seven-fold compared to baseline, making it comparable to that of carburized steels. Microstructure-based finite element modeling provided a theoretical strength limit of ~730 MPa for the composites and indicated that high triaxiality in conjunction with severe equivalent plastic strain in a narrow area between the TiB 2 particles led to early fracture initiations, limiting the ductility.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Room Temperature Stamping of High-Strength Aluminum for Lightweight Structural Automotive Components

The use of aluminum (Al) 7xxx series in automobile structural applications is limited by factors such as its low room-temperature formability in T6 temper and the need for off-line artificial aging to regain high strength if it is formed in soft temper. In this study, two tempers were established that enable Al 7075 blanks to be room temperature stamped to create side impact beams that achieve near-T6 strength without post-forming artificial aging. It is shown that natural aging at room temperature, after solution treatment and before stamping, provides an alternative to high temperature pre-aging and hot stamping techniques in 7xxx alloys. Both tempers enabled room temperature stamping of the beams without cracking, indicating good formability. The Al beams were ~38% lighter than the benchmark boron steel beam. Further, the hardness in the low-deformation regions of the stamped Al beams were within 88% of a conventional 7075-T6 sheet. Paint-bake treatment of the beams appeared to cause over aging, lowering the ultimate tensile strength and ductility. Finite element three point bending simulations of the beams showed higher bending force and energy absorption before failure for the Al 7075 showing good promise for 7xxx series Al as a light-weight alternative to steel beams.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Microstructural evolution in shear-punch tests: A comparative study of pure Cu and Cu-Cr alloy

Understanding the mechanisms behind microstructural evolution during shear deformation has been a long-standing area of interest. However, establishing a connection between microstructure, mechanical properties, and extent of shear deformation is challenging and requires refined experimental approaches. Shear-punch testing (SPT) provides a controlled method to introduce shear into small volumes of material that later can be subjected to detailed microstructural characterization. In this study, we utilize an SPT device to induce shear deformation to pure copper and a binary copper-chromium alloy. Electron backscatter diffraction and transmission electron microscopy were used to study the mechanisms of plastic deformation after SPT. Our results indicate that shear deformation of pure Cu produces a dense network of intercepting microshear bands upon sustained deformation. Twin boundaries undergo degradation into high angle grain boundaries due to simultaneous deviation from the axis-angle pair condition of 60° misorientation on [111] direction. The presence of 50% volume Cr particles in the soft Cu matrix fundamentally altered the shear deformation mechanism. Preferential deformation of the Cu matrix led to accelerated shear-induced formation of low and high angle grain boundaries, and subsequent grain refinement. Comparatively, no grain refinement occurred in pure Cu at a strain ~10 times larger (ϵ = 4.73) than that of the copper-chromium case (ϵ = 0.42). Overall, our study sheds light on the microstructural evolution during shear deformation and highlights the significant influence of particle reinforcements on the shear deformation mechanisms of metals.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Simultaneous improvement in strength and ductility in 7xxx Al through a combination of natural aging and deformation

Room temperature processing methods of reaching near-T6 yield and ultimate tensile strength in Al–Zn–Mg–Cu alloys provide a potentially lower cost alternative to high temperature forming and post-forming artificial aging methods. Here, this study demonstrates a method, where a combination of pre-deformation and natural aging matched T6 strength along with ductility and strain hardening greater than the T6 values. Tensile deformation of 5% and 10% was applied to naturally aged samples at 144 h (6 days) and the samples were further naturally aged up to 220 days. The pre-deformed samples showed strong type A Portevin-Le Chatelier (PLC) banding with limited ductility and strain hardenability. Further natural aging increased both strength and ductility simultaneously and converted PLC to type B. This resulted in the same yield strength as T6 temper in the 10% deformed sample but with almost 77% greater total ductility (including the 10% pre-deformation). The simultaneous increase in strength and ductility was attributed to the small, shearable clusters/precipitates and solutes present in the microstructure as suggested by the changes in the PLC behavior.

36 MATERIALS SCIENCE↗
DOE OSTI2023

An innovative and alternative approach toward gear fabrication

In this paper, we present the first demonstration of single-step gear manufacturing via an innovative in-situ friction stir forging approach. This novel process is a natural extension to the friction stir processing technique and relies on shear and normal stresses to form the complex shapes. Friction stir welding pin tool with shoulder is plunged at high revolutions per minute (rpm) into the sample to heat it to the desired temperature and enable plastic flow. Then, the tool is forged at high plunge rate to form the desired structurally-sound and defect free complex shapes. To better visualize the process the experiments are complemented by a 3D thermomechanically coupled, smoothed particle hydrodynamics (SPH) model to understand the material flow pattern both radially and through thickness in the gear teeth, plastic strain distribution, and temperature profile. We have demonstrated application of I-FSF to inherently poor formable AZ31 Mg, AA 7075-T6, and AA5083–10 vol% TiB 2 composite and fabricated 14-tooth spur gears from these materials with minimal farther machining. In conclusion, microstructure of the forged gears exhibited a directional material flow pattern due to the normal forging action and refinement of grains to 6–13 μm through dynamically recrystallization across the radial, through-thickness direction, which is in good agreement with the corresponding SPH simulation results.

42 ENGINEERING↗
DOE OSTI2022

High-Silicon Steel Strip by Single-Step Shear Deformation Processing

It is well known that Fe-Si alloys with Si content higher than in conventional electrical sheet steels (>3.2% Si) can make a significant impact in improving the efficiency of electrical motors if they are available in sheet/foil (strip) forms at suitable cost. While the magnetic and electrical attributes (e.g., resistivity, core loss) of these high-Si Fe alloys, of relevance to electrical motor core laminations, are known to be exceptional, the alloys have limited workability, making them difficult to produce consistently in sheet/foil (strip) forms. Current processing techniques such as rolling, while adequate for producing conventional electrical steel sheet, do have important disadvantages - large energy consumption and emissions, limitations in processing of low-workability alloys (e.g., high-Si content steels), large-scale plant infrastructure, and less than adequate capability to engineer sheet metals with specific microstructures (e.g., fine-grained) and crystallographic textures (e.g., shear textures). It is therefore of interest to have an alternative commercial process that can produce sheet/foil (strip) from high-Si Fe alloys and which can also overcome some of the deficiencies of current multistage strip processes. The goal of the present project was design and demonstration of a new energy-efficient pilot process for producing high-Si electrical steel strip of commercial widths and thickness, and with superior electrical and magnetic properties than current electrical steels (Fe-3.2% Si as benchmark). The applications domain for these steels is electrical motor core laminations. We have addressed this goal by accomplishment of the following specific objectives and tasks: a) Development of an Fe-4Si-4Cr alloy with electrical resistivity >80 μΩ-cm, induction flux density >1.48 T at 5000 A/m and core loss 35% lower than the benchmark 3.2% Si alloy. The alloy which meets DOE target specifications for motor core attributes was designed with the Si content controlled for the electrical properties and the Cr content tailored to meet material/process workability requirements. b) A unique machining-based deformation processing system was designed and scaled-up to produce strip of commercial width (25 mm to 150 mm) and thickness (up to 0.5 mm) from the Fe-4Si-4Cr alloy and other alloys of varied workability including copper, Al6061-T6 and naval brass. The key attributes of the machining-based strip production are deformation processing by concentrated simple-shear; single-step production of strip from ingot using compact machine infrastructure; strip surface finish of Ra 0.35 to 1 micrometer that is comparable/superior to that of rolled strip; discrete production of strip that can potentially be done at point of use; and controllability of strip mechanical/formability properties by deformation control. c) The electrical, magnetic, surface quality, mechanical, formability, and metallurgical properties/attributes of the machining-based strip were established by direct ASTM standard or equivalent measurement techniques. d) Punching characteristics of the strip in terms of load, edge quality and macro defects were similar to those of conventional 3.2% Si electrical steels. These punching characteristics are critical from a manufacturability perspective for motor/transformer core applications. e) A modeling framework for energy analysis of multistage rolling and the machining-based deformation processing has been established. Application of this modeling to the two strip-processes showed that the machining-based process requires significantly lower specific energy for processing, ~ 25% of that for rolling. The modeling framework can be adapted for a range of sheet-metal forming, bulk metal forming, and machining processes. It can be used to identify key parameters controlling process specific energy. f) A comparative analysis of advantages and disadvantages of machining-based processing against rolling for strip production. The single stage machining-based processing, with compact infrastructure, represents a new manufacturing paradigm for sheet and foil manufacturing that can potentially also be applied to advanced titanium, aluminum, copper and magnesium alloys. The goals and objectives were accomplished by a cross-disciplinary project team comprising of personnel from Purdue University; M4 Sciences LLC, a small-business focused on advanced manufacturing technology development; the Pacific Northwest National Labs; and tool manufacturers. The team is currently in advanced discussions with multiple entities for future process development for commercialization.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Shear strain gradient in Cu/Nb nanolaminates: Strain accommodation and chemical mixing

Disentangling the intragranular and interfacial plasticity contribution to the overall strain accommodation is crucial to understanding the microstructural evolution and mass transport upon deformation in materials with the nanoscale feature size. In this study, we devise a new approach to tackle the issue by introducing shear strain gradients into Cu/Nb nanolaminates of different layer thicknesses with the shear perpendicular to the laminate interfaces. The measurement of the strain gradient and the resultant lattice disorientation enables a quantitative understanding of the intragranular and interfacial plasticity contribution. We found that intragranular slip entirely governs the deformation in the 300 nm-layer laminate and, unexpectedly, contributes ~80% of the total plasticity in the 30 nm-layer laminate. The high intragranular plasticity in the thin laminate is attributed to the large width of confined slip planes and their remnant potential for storing dislocations. In addition, substantial forced chemical mixing is observed in the top region of the 30 nm-layer laminate where the effective layer thickness is reduced below 8 nm. The transition of deformation mechanism from confined layer slip to dislocation transmission is largely responsible for the initiation of substantial mixing. Our method and findings shed light on the deformation mechanism and deformation-induced mass transport behavior in nanostructured materials.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Local Thermomechanical Processing for Improving Formability of High Strength Aluminum Sheets

Limited room temperature formability hinders the wide-spread use of high strength aluminum alloys in structural body-in-white parts. Stamping or extrusion at warm temperatures or from softer tempers are the current solutions. In this work, our approach is to start with age-hardened sheets from 7xxx and 6xxx family of alloys and improve their formability using local thermomechanical processing only in the regions demanding highest ductility in the forming processes. We achieved local formability improvements with friction stir processing and introduce another process named roller-bending as a concept and showed its feasibility through finite element simulations. Initial results from FSP indicated significant deformation in the processed zones with minimal sheet distortion. FSP also resulted in dynamically recrystallized, fine grained (d < 5 µm) microstructures in the processed regions with textures significantly different from the base material. This resulted in formability improvements of > 30% in 7085-T76 and > 50% in 6111-T6 alloys as measured by minimum bend radius (r/t) ratios established with V-bending tests performed at 90° and 180° bend angles. Based on the encouraging initial results, we envision applicability of these processes in both pre- and post-stamping stages through integration of the process tools as end-effectors to robotic arms.

Nasim, Wahaz↗
DOE OSTI2021

Overcoming the Barriers to Lightweighting by Enabling Low-Cost and High-Performance Structural Automotive Aluminum Castings

The major difference between the secondary and primary Al alloys is the amount of Fe in the alloys - recycling of Al alloys gradually leads to an increase in their Fe content. Thus, many secondary alloys allow up to 0.60% Fe as compared to the primary alloys that use between 0.10% and 0.20% Fe. Unfortunately, in Al alloys with higher iron content, iron-intermetallic phases form that are detrimental to the tensile properties and elongation of the Al castings. For example, in A356 alloys with iron at 0.10%, the ductility achieved is typically 8% whereas for secondary 356 alloys with iron around 0.6%, the ductility achieved is 3% or less. These intermetallic phases cannot be effectively modified with standard casting practices or standard heat treatment. Thus, new techniques need to be developed that can help secondary Al alloys overcome the mechanical property and cost barriers and are the focus of this project. We propose to lower the cost penalty and address mechanical properties issues in Al castings by a two-pronged approach: 1. Use an ultrasonics-based technique to modify the size and distribution of the deleterious intermetallics in the castings during the solidification process; and 2. Use PNNL-developed novel heat-treatment technique to lower the temperature and/or shorten the heat-treatment duration post-solidification processing.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Stable, Ductile and Strong Ultrafine HT-9 Steels via Large Strain Machining

Beyond the current commercial materials, refining the grain size is among the proposed strategies to manufacture resilient materials for industrial applications demanding high resistance to severe environments. Here, large strain machining (LSM) was used to manufacture nanostructured HT-9 steel with enhanced thermal stability, mechanical properties, and ductility. Nanocrystalline HT-9 steels with different aspect rations are achieved. In-situ transmission electron microscopy annealing experiments demonstrated that the nanocrystalline grains have excellent thermal stability up to 700 °C with no additional elemental segregation on the grain boundaries other than the initial carbides, attributing the thermal stability of the LSM materials to the low dislocation densities and strains in the final microstructure. Nano-indentation and micro-tensile testing performed on the LSM material pre- and post-annealing demonstrated the possibility of tuning the material’s strength and ductility. The results expound on the possibility of manufacturing controlled nanocrystalline materials via a scalable and cost-effective method, albeit with additional fundamental understanding of the resultant morphology dependence on the LSM conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Limitations of Thermal Stability Analysis via In-Situ TEM/Heating Experiments

This work highlights some limitations of thermal stability analysis via in-situ transmission electron microscopy (TEM)-annealing experiments on ultrafine and nanocrystalline materials. We provide two examples, one on nanocrystalline pure copper and one on nanocrystalline HT-9 steel, where in-situ TEM-annealing experiments are compared to bulk material annealing experiments. The in-situ TEM and bulk annealing experiments demonstrated different results on pure copper but similar output in the HT-9 steel. The work entails discussion of the results based on literature theoretical concepts, and expound on the inevitability of comparing in-situ TEM annealing experimental results to bulk annealing when used for material thermal stability assessment.

36 MATERIALS SCIENCE↗