Search NASA⌕ Search

Engineering topics

Elber, W.

Publications and source records attributed to Elber, W..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2005

Damage Tolerance Issues as Related to Metallic Rotorcraft Dynamic Components

In this paper issues related to the use of damage tolerance in life managing rotorcraft dynamic components are reviewed. In the past, rotorcraft fatigue design has combined constant amplitude tests of full-scale parts with flight loads and usage data in a conservative manner to provide "safe life" component replacement times. In contrast to the safe life approach over the past twenty years the United States Air Force and several other NATO nations have used damage tolerance design philosophies for fixed wing aircraft to improve safety and reliability. The reliability of the safe life approach being used in rotorcraft started to be questioned shortly after presentations at an American Helicopter Society's specialist meeting in 1980 showed predicted fatigue lives for a hypothetical pitch-link problem to vary from a low of 9 hours to a high in excess of 2594 hours. This presented serious cost, weight, and reliability implications. Somewhat after the U.S. Army introduced its six nines reliability on fatigue life, attention shifted towards using a possible damage tolerance approach to the life management of rotorcraft dynamic components. The use of damage tolerance in life management of dynamic rotorcraft parts will be the subject of this paper. This review will start with past studies on using damage tolerance life management with existing helicopter parts that were safe life designed. Also covered will be a successful attempt at certifying a tail rotor pitch rod using damage tolerance, which was designed using the safe life approach. The FAA review of rotorcraft fatigue design and their recommendations along with some on-going U.S. industry research in damage tolerance on rotorcraft will be reviewed. Finally, possible problems and future needs for research will be highlighted.

Everett, R. A., Jr.↗
NASA NTRS2000

The Significance of Small Cracks in Fatigue Design Concepts as Related to Rotorcraft Metallic Dynamic Components

In this paper the significance of the "small" crack effect as defined in fracture mechanics will be discussed as it relates to life managing rotorcraft dynamic components using the conventional safe-life, the flaw tolerant safe-life, and the damage tolerance design philosophies. These topics will be introduced starting with an explanation of the small-crack theory, then showing how small-crack theory has been used to predict the total fatigue life of fatigue laboratory test coupons with and without flaws, and concluding with how small cracks can affect the crack-growth damage tolerance design philosophy. As stated in this paper the "small" crack effect is defined in fracture mechanics where it has been observed that cracks on the order of 300 microns or less in length will propagate at higher growth rates than long cracks and also will grow at AK values below the long crack AK threshold. The small-crack effect is illustrated herein as resulting from a lack of crack closure and is explained based on continuum mechanics principles using crack-closure concepts in fracture mechanics.

Everett, R. A., Jr.↗
NASA NTRS1999

Damage Tolerance Issues as Related to Metallic Rotorcraft Dynamic Components

In this paper issues related to the use of damage tolerance in life managing rotorcraft dynamic components are reviewed. In the past, rotorcraft fatigue design has combined constant amplitude tests of full-scale parts with flight loads and usage data in a conservative manner to provide "safe life" component replacement times. In contrast to the safe life approach over the past twenty years the United States Air Force and several other NATO nations have used damage tolerance design philosophies for fixed wing aircraft to improve safety and reliability. The reliability of the safe life approach being used in rotorcraft started to be questioned shortly after presentations at an American Helicopter Society's specialist meeting in 1980 showed predicted fatigue lives for a hypothetical pitch-link problem to vary from a low of 9 hours to a high in excess of 2594 hours. This presented serious cost, weight, and reliability implications. Somewhat after the U.S. Army introduced its six nines reliability on fatigue life, attention shifted towards using a possible damage tolerance approach to the life management of rotorcraft dynamic components. The use of damage tolerance in life management of dynamic rotorcraft parts will be the subject of this paper. This review will start with past studies on using damage tolerance life management with existing helicopter parts that were safe life designed. Also covered will be a successful attempt at certifying a tail rotor pitch rod using damage tolerance, which was designed using the safe life approach. The FAA review of rotorcraft fatigue design and their recommendations along with some on-going U.S. industry research in damage tolerance on rotorcraft will be reviewed.

Everett, R. A., Jr.↗
NASA NTRS1990

Loading rate sensitivity of open-hole composite specimens in compression

The results are reported of an experimental study on the compressive, time-dependent behavior of graphite fiber reinforced polymer composite laminates with open holes. The effect of loading rate on compressive strength was determined for six material systems ranging from brittle epoxies to thermoplastics at both 75 F and 220 F. Specimens were loaded to failure using different loading rates. The slope of the strength versus elapsed time-to-failure curve was used to rank the materials' loading rate sensitivity. All of the materials had greater strength at 75 F than at 220 F. All the materials showed loading rate effects in the form of reduced failure strength for longer elapsed-time-to-failure. Loading rate sensitivity was less at 220 F than the same material at 70 F. However, C12000/ULTEM and IM7/8551-7 were more sensitive to loading rate than the other materials at 220 F. AS4/APC2 laminates with 24, 32, and 48 plies and 1/16 and 1/4 inch diameter holes were tested. The sensitivity to loading rate was less for either increasing number of plies or larger hole size. The failure of the specimens made from brittle resins was accompanied by extensive delaminations while the failure of the roughened systems was predominantly by shear crippling. Fewer delamination failures were observed at the higher temperature.

Lubowinski, S. J.↗
NASA NTRS1985

Prediction of impact force and duration due to low-velocity impact on circular composite laminates

Two simple and improved models - energy-balance and spring-mass - were developed to calculate impact force and duration during low velocity impact of circular composite plates. Both models include the contact deformation of the plate and the impactor as well as bending, transverse shear, and membrane deformations of the plate. The plate was transversely isotropic graphite/epoxy composite laminate and the impactor was a steel sphere. Calculated impact forces from the two analyses agreed with each other. The analyses were verified by comparing the results with reported test data.

Shivakumar, K. N.↗
NASA NTRS1985

Large deflection behavior of quasi-isotropic laminates under low-velocity impact type point loading

Eight-ply quasi-isotropic circular composite plates of Thornel 300 graphite in Narmco 5208 epoxy resin (T300/5208) were analyzed to obtain the large deformation behavior under low-velocity impact type point loads. A simple plate-membrane coupling model was developed. The impact type point loads were replaced by equivalent quasi-static point loads. The plate-membrane coupling model was used to obtain the large deformation shapes for the thin circular composite laminates. The analyses indicated that the large deformation shapes of the composite plates under point loads vary with the center point displacements, and hence are different for different load levels. Quasi-isotropic plates were analyzed by replacing anisotropic bending stiffness components with the equivalent flexural stiffness for the isotropic plates. The plate-membrane coupling model was verified by conducting a series of tests on clamped circular quasi-isotropic laminates. Deflected shapes for the thin composite plates were experimentally obtained. These shapes agreed well with the analytically predicted shapes.

Kelkar, A.↗
NASA NTRS1985

Large deflections of circular isotropic membranes subjected to arbitrary axisymmetric loading

Circular membranes with fixed peripheral edges, subjected to arbitrary axisymmetric loading were analyzed. A single governing differential equation in terms of radial stress was used. This nonlinear governing equation was solved using the finite difference method in conjunction with Newton-Raphson method. Three loading cases, namely: (1) uniformly loaded membrane, (2) a membrane with uniform load over an inner portion, and (3) a membrane with ring load, were analyzed. Calculated central displacement and the central and edge radial stresses for uniformly loaded membrane, agreed extremely well with the classical solution.

Kelkar, A.↗
NASA NTRS1984

The Effect of Matrix and Fiber Properties on Impact Resistance

The basic material properties which control impact damage are identified and testing techniques are assessed. It is demonstrated that static indentation tests can provide better information about failure processes than impact tests, and they are simpler to conduct. In thin and thick laminates, it was found that the matrix shear strength controls the onset of delamination damage and that the fiber strength controlled the penetration phase. In thin laminates, tough matrices do little to enhance impact resistance.

Elber, W.↗
NASA NTRS1984

Large deflections of circular isotropic membranes subjected to arbitrary axisymmetric loading

Circular membranes with fixed peripheral edges, subjected to arbitrary axisymmetric loading are analyzed. A single governing differential equation in terms of radial stress is used. This nonlinear governing equation is solved using the finite difference method in conjunction with Newton-Raphson method. Three loading cases, namely (1) uniformly loaded membrane, (2) a membrane with uniform load over an inner portion, and (3) a membrane with ring load, are analyzed. Calculated central displacement and the central and edge radial stresses for uniformly loaded membrane, agree extremely well with the classical solution.

Kelkar, A.↗
NASA NTRS1984

Delamination growth analysis in quasi-isotropic laminates under loads simulating low-velocity impact

A geometrically nonlinear finite-element analysis was developed to calculate the strain energy released by delamination plates during impact loading. Only the first mode of deformation, which is equivalent to static deflection, was treated. Both the impact loading and delamination in the plate were assumed to be axisymmetric. The strain energy release rate in peeling, G sub I, and shear sliding, G sub II, modes were calculated using the fracture mechanics crack closure technique. Energy release rates for various delamination sizes and locations and for various plate configurations and materials were compared. The analysis indicated that shear sliding (G sub II) was the primary mode of delamination growth. The analysis also indicated that the midplane (maximum transverse shear stress plane) delamination was more critical and would grow before any other delamination of the same size near the midplane region. The delamination growth rate was higher (neutrally stable) for a low toughness (brittle) matrix and slower (stable) for high toughness matrix. The energy release rate in the peeling mode, G sub I, for a near-surface delamination can be as high as 0.5G sub II and can contribute significantly to the delamination growth.

Shivakumar, K. N.↗
NASA NTRS1984

Fatigue and Fracture Branch: A compendium of recently completed and on-going research projects

This compendium of recently completed and ongoing research projects from the Fatigue and Fracture Branch at NASA Langley Research Center provides technical descriptions and key results of all such projects expected to lead to publication of significant findings. The common thread to all these studies is the application of fracture mechanics analyses to engineering problems in metals and composites, with particular emphasis on airframe structural materials. References to recent publications are included where appropriate.

Elber, W.↗
NASA NTRS1984

Delamination growth analysis in quasi-isotropic laminates under loads simulating low-velocity impact

A geometrically nonlinear finite-element analysis has been developed to calculate the strain energy released by delaminating plates during impact loading. Only the first mode of deformation, which is equivalent to static deflection, was treated. Both the impact loading and delamination in the plate were assumed to be axisymmetric. The strain energy release rate in peeling, GI, and shear sliding, GII, modes were calculated using the fracture mechanics crack closure technique. Energy release rates for various delamination sizes and locations and for various plate configurations and materials were compared. The analysis indicated that shear sliding was the primary mode of delamination growth. The analysis also indicated that the midplane (maximum transverse shear stress plane) delamination was more critical and would grow first before any other delamination of the same size near the midplane region. The delamination growth rate was higher (neutrally stable) for a low toughness (brittle) matrix and slower (stable) for high toughness matrix. The energy release rate in the peeling mode, GI, for a near-surface delamination can be as high as 0.5GII, and can contribute significantly to the delamination growth.

Shivakumar, K. N.↗
NASA NTRS1983

Prediction of impact force and duration during low velocity impact on circular composite laminates

Two simple and improved models--energy-balance and spring-mass--were developed to calculate impact force and duration during low velocity impact of circular composite plates. Both models include the contact deformation of the plate and the impactor as well as bending, transverse shear, and membrane deformations of the plate. The plate was transversely isotropic graphite/epoxy composite laminate and the impactor was a steel sphere. Calculated impact forces from the two analyses agreed with each other. The analyses were verified by comparing the results with reported test data.

Shivakumar, K. N.↗
NASA NTRS1983

Failure mechanics in low-velocity impacts on thin composite plates

Eight-ply quasi-isotropic composite plates of Thornel 300 graphite in Narmco 5208 epoxy resin (T300/5208) were tested to establish the degree of equivalence between low-velocity impact and static testing. Both the deformation and failure mechanics under impact were representable by static indentation tests. Under low-velocity impacts such as tool drops, the dominant deformation mode of the plates was the first, or static, mode. Higher modes are excited on contact, but they decay significantly by the time the first-mode load reaches a maximum. The delamination patterns were observed by X-ray analysis. The areas of maximum delamination patterns were observed by X-ray analysis. The areas of maximum delamination coincided with the areas of highest peel stresses. The extent of delamination was similar for static and impact tests. Fiber failure damage was established by tensile tests on small fiber bundles obtained by deplying test specimens. The onset of fiber damage was in internal plies near the lower surface of the plates. The distribution and amount of fiber damage was similar fo impact and static tests.

Elber, W.↗
NASA NTRS1983

Slow crack growth in spinel in water

Magnesium aluminate spinel was tested in a water environment at room temperature to establish its slow crack-growth behavior. Ring specimens with artificial flaws on the outside surface were loaded hydraulically on the inside surface. The time to failure was measured. Various precracking techniques were evaluated and multiple precracks were used to minimize the scatter in the static fatigue tests. Statistical analysis techniques were developed to determine the strength and crack velocities for a single flaw. Slow crack-growth rupture was observed at stress intensities as low as 70 percent of K sub c. A strengthening effect was observed in specimens that had survived long-time static fatigue tests.

Schwantes, S.↗
NASA NTRS1983

Analysis of progressive damage in thin circular laminates due to static-equivalent impact loads

Clamped circular graphite/epoxy plates (25.4, 38.1, and 50.8 mm radii) with an 8-ply quasi-isotropic layup were analyzed for static-equivalent impact loads using the minimum-total-potential-energy method and the von Karman strain-displacement equations. A step-by-step incremental transverse displacement procedure was used to calculate plate load and ply stresses. The ply failure region was calculated using the Tsai-Wu criterion. The corresponding failure modes (splitting and fiber failure) were determined using the maximum stress criteria. The first-failure mode was splitting and initiated first in the bottom ply. The splitting-failure thresholds were relatively low and tended to be lower for larger plates than for small plates. The splitting-damage region in each ply was elongated in its fiber direction; the bottom ply had the largest damage region. The calculated damage region for the 25.4-mm-radius plate agreed with limited static test results from the literature.

Shivakumar, K. N.↗