Elizabeth F Rieken | Search NASA

NASA NTRS2024

Experimental and Computational Study of Convective Heating on the Aeroshell Back Side and Payload of the LOFTID Vehicle

A wind tunnel test program was conducted to obtain experimental convective heating data on models of the Low Earth Orbital Flight Test of an Inflatable Decelerator (LOFTID) vehicle in support of the flight test program. Wind tunnel testing was conducted at Mach 6 and Mach 10 at unit Reynolds numbers from 0.5×106/ft to 4.0×106/ft on 6.0inch diameter aeroshell models. Global heating data were obtained through phosphor thermography measurements on the front and back of the aeroshell and on the payload. For all test conditions, attached, laminar flow was definitively produced on the front of the aeroshell, while in the wake the flow was separated, unsteady and possibly transitional or turbulent. A complementary computational study was performed to assess the accuracy of heating predictions for LOFTID wake flow environments. A new grid topology was developed for the study to allow the use of structured grid solvers for complex, open-backed geometries such as that of LOFTID. Close agreement between measurements and predictions was obtained on the front of the aeroshell. Comparisons were more challenging in the wake because of both the extremely low heating rates and the accompanying high uncertainties and the unsteady nature of the separated wake flow simulations. While the differences between heating predictions and measurements for the wake flow were higher than for the forebody flow, these differences were used to assist in the definition of conservative uncertainty margins for predictions of the flight environments for the successful flight test of the LOFTID vehicle in November 2022.

LOFTID↗

NASA NTRS2024

Application of PLIF to Investigate the Hypersonic Wake of a LOFTID-Relevant Model at Mach 10

An experimental investigation of hypersonic wake flows using the planar laser-induced fluorescence (PLIF) measurement technique is summarized in this report. Off-body measurements, primarily flow visualization and velocity, were obtained for the wake of a blunt body model relevant for terrestrial re-entry and Martian entry applications within a Mach 10 hypersonic flow. The design of the model was based on the forebody aeroshell used for the LOFTID (Low-Earth Orbit Flight Test of an Inflatable Decelerator) flight vehicle. This document serves to document the experimental conditions and provide an initial analysis of select test conditions.

PLIF↗

NASA NTRS2020

NASA Langley Aerothermodynamic Ground Tests in Support of the Boundary Layer Transition (BOLT) Flight Experiment

The Air Force Office of Scientific Research (AFOSR) has sponsored the Boundary Layer Transition (BOLT) Experiments to investigate hypersonic boundary layer transition on a low-curvature, concave surface with swept leading edges. This paper provides a review of aerothermodynamic ground test contributions by NASA Langley Research Center to the design of the BOLT flight experiment. Several test entries into the Langley Aerothermodynamics Laboratory 20-Inch Mach 6 Air Tunnel are discussed. Global surface heating distributions on subscale BOLT models were measured using either phosphor thermography or infrared thermography at a range of model attitudes and freestream Reynolds numbers. An initial test entry provided the first experimental measurements of transition on the BOLT geometry. A second test entry investigated the effects of distributed surface roughness along the swept leading edges. A third test entry provided an evaluation of the aeroheating environment on the aerodynamic fairings and a portion of the flight vehicle downstream of the BOLT experiment. These entries were intended to support the development and design of flight hardware and instrumentation for the BOLT flight experiment.

Elizabeth F Rieken↗

NASA NTRSDate not supplied

Aftbody Aeroheating Wind Tunnel Measurements on a Hypersonic Inflatable Aerodynamic Decelerator

The aftbody aeroheating environment of a Hypersonic Inflatable Aerodynamic Decelerator (HIAD) was investigated in the NASA Langley 31-Inch Mach 10 Air Tunnel. The wind tunnel model geometry was representative of the Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) vehicle. Aeroheating data were obtained for a range of Reynolds numbers and angles-of-attack using global phosphor thermography. Aeroheating data were also obtained using a developmental IR thermography technique for evaluation of data quality.

Elizabeth F Rieken↗

NASA NTRSDate not supplied

CFD Validation Study of a Hypersonic Cone-Slice-Flap Configuration

Model validation is the process of determining the degree of accuracy between the real world and the model. The result of model validation can be used to either improve the model through calibration or quantify the model-form uncertainty. This work focuses on estimating the model-form uncertainty through an area metric for a hypersonic cone-slice-flap geometry configuration given the uncertainty in both the simulation and experimental data. A procedure that can give an accurate representation of the model-form uncertainty using a small number of high-fidelity runs is outlined. The work also assesses the impact of using different high-fidelity solvers and different turbulence models. The goal of performing this comparison is to provide a quantifiable measurement of the accuracy of each solver and turbulence model for this type of design. A low-fidelity analysis is also performed to get a model-form uncertainty for this type of analysis. The two high-fidelity CFD solvers used here are VULCAN-CFD and FUN3D, and the low-fidelity results comes from Cart3D.The experimental data comes from the 20-inch Mach 6 Tunnel located at NASA Langley Research Center. The work here shows that the models used tend to under-predict the drag and moment aerodynamic coefficients for this type of design leading to a model-form uncertainty estimate which can account for up to an 86% of the total uncertainty in the model predictions.

Laura M White↗

NASA NTRSDate not supplied

Overview of the High Reynolds Number Ascent Wind Tunnel Test of the Space Launch System at the National Transonic Facility

Transonic, high Reynolds number wind tunnel testing for the Space Launch System (SLS) ascent flight environment was conducted in the National Transonic Facility (NTF) at the NASA Langley Research Center from December 2019 to April 2021. The test was sponsored by the SLS Program and the NASA Engineering & Safety Center with the ob- jective of assessing and characterizing Reynolds number effects on the ascent aerodynamics of the SLS launch vehicle. The cryogenic test article was a 1.75%-scale representation of the SLS Block 1 Cargo configuration that was fabricated mostly out of stainless steel, but with several additive-manufactured components including the Solid Rocket Booster (SRB) attach brackets and the SRB nozzles. This was the first use of additive manufacturing on structural components of a cryogenic model in the NTF, therefore post-fabrication material testing and inspections were performed to satisfy safety requirements. Force & moment and surface pressure data were acquired for Mach numbers between 0.50 and 0.95 over a range of Reynolds numbers based on core stage diameter between 2x10^6 and a maximum of 40x10^6 corresponding to 45% of flight Reynolds number. Additionally, flow visualization data using Pressure Sensitive Paint were acquired with a focus on the SRB forward attach area, which is susceptible to Reynolds number sensitivity at transonic speeds. This pa- per provides an overview of the test campaign including details on the unique test article and the experimental setup and test execution. General test findings and observations are also presented, but the majority of the test results and data analyses are provided in a companion paper.

Space Launch System↗

NASA NTRSDate not supplied

A Spectrum of Stakeholder Perspective Taking in Early-Stage Design

Stakeholder perspective taking is a critical skill in early-stage problem exploration and framing. We examined stakeholder perspective taking within a professional engineering early-stage design team at NASA to begin to understand in what ways and under what conditions designers adopt stakeholder perspectives. Our findings identify a spectrum of perspective taking during problem framing deliberations that ranges from (1) fully taking the stakeholder’s point of view (POV), (2) interpreting the stakeholder’s POV with a designer’s POV, (3) implanting the stakeholder’s POV into a designer’s POV, to (4) fully taking a designer’s own POV. We also begin to identify and describe conditions that encourage and hinder stakeholder perspective taking in real-world early-stage design settings. These findings are significant because they suggest ways to gauge and encourage the skill of perspective taking among highly technical engineers working on design challenges with real-world, societal implications.

perspective taking↗

NASA NTRSDate not supplied

Force and Moment Analysis for the High Reynolds Number Wind Tunnel Test of the Space Launch System at Ascent Conditions

A high Reynolds number test of the Space Launch System was performed at the NASA Langley National Transonic Facility (NTF). The objective of the test was to use the cryogenic testing capabilities of the NTF to acquire data over the largest range of Reynolds numbers possible with a specific focus on the Reynolds numbers closest to flight conditions. The test was performed at Mach numbers from 0.50 to 0.95 which corresponds to the ascent portion of flight for the SLS vehicle. Force and moment data showed that pitching and yawing moment were sensitive to Reynolds number effects over the full range of Mach and Reynolds numbers tested. Axial force also showed sensitivity to Reynolds number with the largest differences seen between Mach 0.50 to 0.90. Surface pressure data showed the highest sensitivity to Reynolds number in the vicinity of the solid rocket booster forward attach region.

Space Launch System↗

NASA NTRSDate not supplied

FLEET and PLIF Velocimetry Within A Mach 10 Hypersonic Air Flow

Femtosecond laser electronic excitation tagging (FLEET) and planar laser-induced fluorescence (PLIF) velocity measurements utilizing molecular tagging velocity (MTV) methods from three recent test campaigns conducted at the 31-in Mach 10 Air Tunnel at the NASA Langley Research Center are highlighted within. The FLEET measurements reported here include the first direct measurement of freestream velocity at this hypersonic wind tunnel facility. Measurement challenges were exasperated by the low gas density of the Mach 10 air freestream (~0.4% of standard temperature and pressure conditions) and even lower gas densities within the hypersonic wake of a 70-degree sphere-cone model. In addition, the hypersonic freestream and very low speed velocities in the wake also tested the measurement dynamic range. To complement the FLEET measurements in the wake of the sphere-cone model, PLIF velocimetry using seeded nitric oxide was also performed. While NO-PLIF velocimetry has been performed at this facility several times by previous researchers, the use of a 1D diffractive optical element for NO-PLIF velocimetry is reported here for the first time. The 1D DOE enabled the generation of up to 75 laser lines simultaneously and improved the spatial extent of the measurement three times compared to previous work. This enabled a wide velocity measurement plane of approximately 130 mm x 130 mm. The velocimetry methods demonstrated here are expected to improve wind tunnel characterization, provide critical data to validate CFD codes, and improve the design of flight vehicles for planetary entry.

FLEET↗

NASA NTRSDate not supplied

Aerothermodynamic Analyses for the LOFTID Technology Demonstration Mission

On November 10, 2023, the LOFTID flight test successfully demonstrated the aerodynamic and thermal protection system performance of an inflatable aeroshell at conditions relevant to an operational mission. Aerodynamic performance and aeroheating environment databases for this mission were generated using multiple computational tools for the rarefied, hypersonic, and supersonic flow regimes, supplemented by wind tunnel testing to obtain aeroshell boundary-layer transition and wake flow simulation validation data. A detailed discussion of tools, methods and results is presented herein.

Brian R. Hollis↗

NASA NTRSDate not supplied

Aerothermodynamic Analyses for the LOFTID Technology Demonstration Mission

On November 10, 2023, the LOFTID flight test successfully demonstrated the aerodynamic and thermal protection system performance of an inflatable aeroshell at conditions relevant to an operational mission. Aerodynamic performance and aeroheating environment databases for this mission were generated using multiple computational tools for the rarefied, hypersonic, and supersonic flow regimes, supplemented by wind tunnel testing to obtain aeroshell boundary-layer transition and wake flow simulation validation data. A detailed discussion of tools, methods and results is presented herein.

Brian R. Hollis↗

NASA NTRSDate not supplied

FLEET and PLIF Velocimetry Within A Mach 10 Hypersonic Air Flow

Femtosecond laser electronic excitation tagging (FLEET) and planar laser-induced fluorescence (PLIF) velocity measurements utilizing molecular tagging velocity (MTV) methods from three recent test campaigns conducted at the 31-in Mach 10 Air Tunnel at the NASA Langley Research Center are highlighted within. The FLEET measurements reported here include the first direct measurement of freestream velocity at this hypersonic wind tunnel facility. Measurement challenges were exasperated by the low gas density of the Mach 10 air freestream (~0.4% of standard temperature and pressure conditions) and even lower gas densities within the hypersonic wake of a 70-degree sphere-cone model. In addition, the hypersonic freestream and very low speed velocities in the wake also tested the measurement dynamic range. To complement the FLEET measurements in the wake of the sphere-cone model, PLIF velocimetry using seeded nitric oxide was also performed. While NO-PLIF velocimetry has been performed at this facility several times by previous researchers, the use of a 1D diffractive optical element for NO-PLIF velocimetry is reported here for the first time. The 1D DOE enabled the generation of up to 75 laser lines simultaneously and improved the spatial extent of the measurement three times compared to previous work. This enabled a wide velocity measurement plane of approximately 130 mm x 130 mm. The velocimetry methods demonstrated here are expected to improve wind tunnel characterization, provide critical data to validate CFD codes, and improve the design of flight vehicles for planetary entry.

FLEET↗

NASA NTRSDate not supplied

Operationalizing “Wickedness” as Analytical and Creative Tools to Transform Aviation

As the world grows increasingly networked and complex, so do challenges faced by aviation and technology professionals (e.g., fighting wildfires and increasing access to healthcare). There is a need to develop new methods to tackle complex socio-technical problems relevant to aviation. The concept of “wicked” problems offers new methods and perspectives for framing complex challenges. In this paper, we present two modes of operationalizing “wickedness” used by NASA’s Convergent Aeronautics Solutions (CAS) Project to develop transformative innovations in aviation: as an analytical, evaluative tool and a creative, generative tool. Through project examples, we demonstrate that using wickedness as a creative tool during the design process enables rich problem exploration with diverse stakeholders and reflection on how a problem is formulated, while usage as an analytical tool can provide criteria for project selection if internal agreement on the definitions of such criteria is established. Operationalizing wickedness as a creative tool may also enable organizational development of a generative mindset to better adapt to our rapidly changing future.

Robyn C Richmond↗