Engineering topics

Elizabeth K Benitez

Publications and source records attributed to Elizabeth K Benitez.

5 records

NASA NTRS2021

Boundary Layer Instabilities Over a Cone-Cylinder-Flare Model at Mach 6

Computations are performed to investigate the boundary-layer instabilities over a sharp cone-cylinder-flare model at zero degrees angle of attack. The model geometry and the flow conditions are selected to match the experiments conducted in the Boeing/AFOSR Mach 6 Quiet Tunnel (BAM6QT) at Purdue University. The geometry consists of a nominally sharp 5-degree half-angle cone, followed by a cylindrical segment and then a 10-degree flare. An axisymmetric separation bubble is generated as a result of the laminar shock/boundary-layer interaction in the cylinder-flare region. The comparison of the laminar flow solution and the schlieren images shows a remarkable agreement between the respective locations of both the boundarylayer edge and the reattachment shock. The predicted heat flux distribution is also in agreement with the measured values downstream of the reattachment location. The analysis of convective and global instabilities is performed for flare half angles equal to 8, 10, and 12 degrees and nosetip radii equal to 0.1, 1, and 5 mm. The linear amplification of first and second Mack mode instabilities that begin to amplify in the cone region are computed with a combination of the parabolized stability equations (PSE) and the harmonic linearized Navier-Stokes equations (HLNSE). The predicted frequency spectra of the surface pressure fluctuations associated with both planar and oblique instability waves are compared with the measured spectra at the various locations of the PCB and Kulite sensors. The comparison shows that the computational analysis captures the distinct lobes within the disturbance amplification spectra measured in the experiments, but some differences in amplification characteristics are noted at low frequencies. Overall, the oblique disturbances are found to be more amplified than the planar disturbances. To our knowledge, this represents the first successful comparison between convective instability analysis and measured surface pressure fluctuations for a hypersonic configuration with a separation bubble. Finally, the global instability analysis shows that the laminar flow becomes supercritical for flare half angles larger than 8 degrees. The unstable global mode for the experimental configuration of a 10 degrees flare and a sharp nosetip cone corresponds to a stationary three-dimensional disturbance that is concentrated in the recirculation region and achieves its maximum growth rate for an azimuthal wavenumber of 5.

Boundary layer transition↗

NASA NTRSDate not supplied

Separation and Transition on the ROTEX-T Cone-Flare

As part of NATO STO AVT-346 “Predicting Hypersonic Boundary-Layer Transition on Complex Geometries,” coordinated experimental and computational studies were conducted on the ROTEX-T, a cone-flare geometry used in a successful flight-test experiment. At the as-flown conditions, a separation bubble existed at the compression corner. Separation, reattachment, and the multifaceted linear instability paths leading this bubble to transition to turbulence are challenging to predict, but have significant impact on surface pressure and heat flux. High-resolution background-oriented schlieren and infrared thermography measurements were made in the AFOSR–Notre Dame Large Mach-6 Quiet Tunnel at freestream unit Reynolds numbers from 5.8×10(exp 6) to 12.2×10(exp 6) m-1and nominally zero angle of attack. High-speed self-aligned focusing schlieren, infrared thermography, and focused laser differential interferometry measurements were made in the AFRL Mach-6 Ludwieg Tube from 2.2×10(exp 6) to 24.7×10(exp 6) m-1and nominally zero degrees angle of attack. The surface heat-flux and Stanton number distributions were computed. Separation and reattachment locations, as well as the flow state at each, were determined from the combination of surface and off-wall measurements. The convective and global boundary-layer instabilities of the axisymmetric laminar flow at the experimental conditions were investigated computationally. Amplification of Mack’s first and second modes were observed to have logarithmic amplification factors between 5 to 7.5 at the separation location, depending on conditions. The flow was found to be globally unstable to stationary three-dimensional disturbances concentrated in the reattachment region. Previous analysis of the ROTEX-T flight data had not assessed reattachment location or the flow state upon reattachment. Thanks to the insights gained from the coordinated, on- and off-wall ground-test measurements, these evaluations have now been made. The separation location indicated by laminar simulations is consistently numerically predicted to be upstream of the experimentally observed location for a transitional separation bubble. The cause of this difference is understood to lie in the steady-state and axisymmetric assumptions made by both solvers employed to compute the basic states analyzed, as flow topology considerations assert that unsteady two-dimensional or axisymmetric separation bubbles are structurally unstable and will become three-dimensional. Computed laminar heating rates prior to separation agreed well with experiment; transitional heating rates after reattachment were between laminar and turbulent computations.

CFD Validation↗

NASA NTRSDate not supplied

Separation and Transition on a CCF: Experimental Campaigns

Several experimental campaigns have been conducted across a number of Mach-6 facilities on the hypersonic flow around a CCF (CCF) geometry with a 5° half-angle cone and a 12° half-angle flare. These experiments were conducted as part of the NATO STO Research Task Group AVT-346, which is focused on predicting hypersonic boundary-layer transition on complex geometries. Two conventional wind tunnels (AFRL M6LT and ONERA R2Ch) and one quiet tunnel (Purdue BAM6QT) were used to test the same CCF geometry and to study the instabilities in both the boundary layer in the attached parts of the flow and the shear layer above the axisymmetric separation bubble near the cylinder-cone junction. Two nosetip radii (one nominally sharp and one blunt with a 5 mm radius) were tested. For the sharp nosetip case, there was a great deal of agreement between the measurements of both second-mode and shear-layer instabilities across the two conventional facilities. However, the measured spectra for the blunt nosetip case showed more significant differences between the two tunnels, potentially due to an alternate dominant instability mechanism coupled with the variations in the freestream noise spectra. The quiet facility resulted in a flow that remained laminar to much higher freestream unit Reynolds numbers, as well as in instability measurements that had more distinct spectral peaks for the sharp tip case and broadband rises for the blunt one. The instability mechanisms at play in the sharp quiet case were found to be the same as those in the conventional facilities.

Boundary Layer Transition↗

NASA NTRSDate not supplied

Separation and Transition on a Cone-Cylinder-Flare: Computational Investigations

Base flow computation and stability analysis were conducted for hypersonic flow over a cone-cylinder-flare (CCF) geometry for conditions that correspond to the experimental runs carried out in three wind tunnels. Owing to the presence of an attached boundary layer, a separation bubble induced by a shock-boundary layer interaction, and a reattachment region, the chosen flow configuration is physically rich. The complexity of this flowfield encompasses a combination of convective instabilities developing on the cone, global instabilities in the separation bubble, and shear-layer modes and streaks in the reattachment region. Thus, the selected CCF configuration provides the opportunity for a comprehensive comparison of the currently available methodologies for analyzing boundary layer instabilities. Various tools are used for the analysis, including global stability codes as well as convective instability analyses based on a local theory, a weakly non-parallel analysis, and tools that are applicable to strongly non-parallel flows. The paper presents a comparison of the convective instability characteristics based on different methodologies, such as linear stability theory (LST), the harmonic form of linearized Navier-Stokes equations (HLNSE), and resolvent analysis. The CCF configuration provided an effective framework for conducting a detailed cross-validation of this type, which had not yet been addressed in existing literature. This document is accompanied by a companion paper that is focused on the experimental aspects of the CCF configuration. Both papers are being presented in a dedicated session that highlights the research activities of the NATO STO Research Task Group AVT-346.

Boundary Layer Transition↗

NASA NTRSDate not supplied

Focused Laser Differential Interferometry: Recent Developments and Applications for Flow Measurements

Focused laser differential interferometry (FLDI), first introduced in the 1970s, has developed into a powerful tool for the analysis of turbulent dynamics and fluctuations in fluid flows ranging from subsonic to hypersonic. This paper provides a review of recent FLDI developments and applications, including discussions on the basic theory of the instrument, various forms of FLDI, multi-point techniques, utilization in fluid flow measurements, quantitative measurement capabilities, and more.

Elizabeth K Benitez↗