Search NASA⌕ Search

Engineering topics

Emma, P

Publications and source records attributed to Emma, P.

A plan for the development of superconducting Undulator prototypes for LCLS-II and future FELs

Copyright © 2014 CC-BY-3.0 and by the respective authors. Undulators serve as the primary source of radiation for modern storage rings, and more recently for the advent of Free-Electron Lasers (FELs). The performance of future FELs can be greatly enhanced using the much higher magnetic fields of superconducting undulators (SCU) [1]. For example, the LCLS-II hard x-ray undulator can be shortened by up to 70 m using an SCU in place of a PMU (permanent magnet undulator), or its spectral performance can be critically improved when using a similar length. In addition, SCUs are expected to be orders of magnitude less sensitive to radiation dose; a major issue at LCLS-II with its 1-MHz electron bunch rate. We present a funded R&D collaboration between SLAC, ANL, and LBNL, which aims to demonstrate the viability of superconducting undulators for FELs by building, testing, measuring, and tuning two 1.5-m long planar SCU prototypes using two different technologies: NbTi at ANL and Nb3Sn at LBNL. Our goal is to review and reassess the LCLS-II HXR baseline plans (PMU) in July of 2015, after the development and evaluation of both prototypes, possibly in favor of an SCU for LCLS-II.

Emma, P↗

Resistive Wall Heating of the Undulator in High Repetition Rate

In next generation high repetition rate FELs, beam energy loss due to resistive wall wakefields will produce significant amount of heat. The heat load for a superconducting undulator (operating at low temperature), must be removed and will be expensive to remove. In this paper, we study this effect in an undulator proposed for a Next Generation Light Source (NGLS) at LBNL. We benchmark our calculations with measurements at the LCLS and carry out detailed parameter studies using beam from a start-to-end simulation. Our preliminarym results suggest that the heat load in the undulator is about 2 W/m or lower with an aperture size of 6 mm for nominal NGLS preliminary design parameters.

43 PARTICLE ACCELERATORS↗

Linac Sector 21-30 'QE' Quadrupole Magnet Excitation in LCLS Operation

The existing SLAC linac quadrupole magnets, described as the 'QE' quadrupoles, are designed for excitation currents up to 200 A with length-integrated gradients up to 100 kG needed to focus up to 50-GeV electron or positron beams. The eight 'QE' magnets within a linac sector are powered in series on a single 200-A bulk power supply, and each magnet in sectors 21-29 also includes a 20-A booster supply (adds 0-20 A to each magnet) for gradient tapering within the sector. Sector 30 is different again with individual 200-A power supplies per magnet. The LCLS will use these same quadrupole magnets, mostly in their existing locations and with their present power supplies, but for an electron energy range of 0.25-14 GeV. This much lower beam energy will require good power supply regulation ({le} 0.05% rms for f > 0.5 Hz) [1] and accurate field excitation at much lower currents, as low as a few amperes. The present (pre-2006) gradient-to-current polynomials (IVBU) in the SLC database are based on magnetic measurements at excitation currents above 20 A, and are not accurate in extrapolation below about 10 A. For this reason the IVBU polynomials for all 'QE' quadrupoles in sectors 21-30 will be updated in 2007 for LCLS operation. Magnets beyond Q21601 will be updated with a new generic polynomial (with polarity considerations) based on magnetic measurements from zero current all the way up to 200 A, with additional data taken in the 0-20 A range for accuracy in LCLS mode (see Fig. 1). In addition, the first five LCLS 'QE' magnets (Q21201, Q21301, Q21401, Q21501, and Q21601), most of which run at the lowest currents of <3 A, have been individually measured and fitted with a specific polynomial to meet their special settings in LCLS mode. All changes will continue to fully support 30-50 GeV linac operations. This note describes these changes and the method used to arrive at this solution. Regulation tests have already been run on both the bulk and booster power supplies which demonstrate a regulation level below 0.05% rms [1]. Table 2 lists a summary of the gradient-to-current polynomials needed in 2007 for all 'QE' magnets from sector-21 to 30.

43 PARTICLE ACCELERATORS↗

A Single-Shot Method for Measuring Femtosecond Bunch Length in Linac-Based Free-Electron Lasers

There is growing interest in the generation and characterization of femtosecond and subfemtosecond pulses from linac-based free-electron lasers (FELs). In this report, following the method of Ricci and Smith [Phys. Rev. ST Accel. Beams 3, 032801 (2000)], we investigate the measurement of the longitudinal bunch profile of an ultrashort electron bunch produced by these FELs. We show that this method can be applied in a straightforward manner at x-ray FEL facilities such as the Linac Coherent Light Source by slightly adjusting the second bunch compressor followed by running the bunch on an rf zero-crossing phase of the final linac. We find that the linac wakefield strongly perturbs the measurement, and through analysis show that it can be compensated in a simple way. We demonstrate the effectiveness of this method and wakefield compensation through numerical simulations, including effects of coherent synchrotron radiation and longitudinal space charge. When used in conjunction with a high-resolution electron spectrometer, this method potentially reveals the temporal profile of the electron beam down to the femtosecond and subfemotsecond scale.

43 PARTICLE ACCELERATORS↗

Free electron lasers: Present status and future challenges

With the scientific successes of the soft X-ray FLASH facility in Germany and the recent spectacular commissioning of the Linac Coherent Light Source at SLAC, free electron lasers are poised to take center stage as the premier source of tunable, intense, coherent photons of either ultra-short time resolution or ultra-fine spectral resolution, from the far infrared to the hard X-ray regime. This paper examines the state of the art in FEL performance and the underlying enabling technologies. It evaluates the state of readiness of the three basic machine architectures—SASE FELs, seeded FELs, and FEL oscillators—for the major X-ray science user facilities on the 5–10 years time scale and examines the challenges that lie ahead for FELs to achieve their full potential throughout the entire spectral range. In soft and hard X-rays, high longitudinal coherence, in addition to full transverse coherence, will be the key performance upgrade; ideas using laser-based or self-seeding or oscillators can be expected to be qualitatively superior to today&#x27;s SASE sources. Short pulses, from femtoseconds to attoseconds, can be realistically envisioned. With high repetition rate electron sources coupled to superconducting radiofrequency linear accelerators, unprecedented average beam brightness will be possible and many users would be served simultaneously by a single accelerator complex.

43 PARTICLE ACCELERATORS↗

Beam-based Feedback for the Linac Coherent Light Source

Beam-based feedback control loops are required by the Linac Coherent Light Source (LCLS) program in order to provide fast, single-pulse stabilization of beam parameters. Eight transverse feedback loops, a 6 x 6 longitudinal feedback loop, and a loop to maintain the electron bunch charge were successfully prototyped in MATLAB for the LCLS, and have been maintaining stability of the LCLS electron beam at beam rates up to 30Hz. In the final commissioning phase of LCLS the beam will be operating at up to 120Hz. In order to run the feedback loops at beam rate, the feedback loops will be implemented in EPICS IOCs with a dedicated ethernet multi-cast network. This paper will discuss the design of the beam-based Fast Feedback System for LCLS. Topics include MATLAB feedback prototyping, algorithm for 120Hz feedback, network design for fast data transport, actuator and sensor design for single-pulse control and sensor readback, and feedback configuration and runtime control.

43 PARTICLE ACCELERATORS↗