Search NASA⌕ Search

Engineering topics

Engel, C. D.

Publications and source records attributed to Engel, C. D..

At least 19 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

SRB thermal environments

The objective was to utilize and expand the Solid Rocket Booster (SRB) orbital flight test data base for better predictions of future flight environments. There were five tasks associated with this effort: analyze the internal aft skirt wind tunnel data and incorporate it into a data base for generating design and preflight reeentry thermal environments; generate reentry design thermal environments for the SRB steel case with the nozzle extension off; generate reentry design thermal environments for the SRB Filament Wound Case with the nozzle extension off; develop an engineering tool to analyze the 3-D flowfield around the SRB aft skirt during reentry for the purpose of obtaining the frequency and severity of the belching gas intrusion internal to the aft skirt; and perform SRM transient joint flow analysis for subscale and full scale motor firing as well as determine the effects of debonds of the insulation on the fill time and heating within the field joint insulation. In addition, this work was extended to provide support for the 51L Shuttle SRB failure analysis.

Crain, W. K.↗
NASA NTRS1989

SRB ascent aerodynamic heating design criteria reduction study, volume 1

An independent set of solid rocket booster (SRB) convective ascent design environments were produced which would serve as a check on the Rockwell IVBC-3 environments used to design the ascent phase of flight. In addition, support was provided for lowering the design environments such that Thermal Protection System (TPS), based on conservative estimates, could be removed leading to a reduction in SRB refurbishment time and cost. Ascent convective heating rates and loads were generated at locations in the SRB where lowering the thermal environment would impact the TPS design. The ascent thermal environments are documented along with the wind tunnel/flight test data base used as well as the trajectory and environment generation methodology. Methodology, as well as, environment summaries compared to the 1980 Design and Rockwell IVBC-3 Design Environment are presented in this volume, 1.

Crain, W. K.↗
NASA NTRS1984

Boundary layer simulator improvement

High chamber pressure expander cycles proposed for orbit transfer vehicles depend primarily on the heat energy transmitted from the combustion products through the thrust wall chamber wall. The heat transfer to the nozzle wall is affected by such variables as wall roughness, relamarization, and the presence of particles in the flow. Motor performance loss for these nozzles with thick boundary layers is inaccurate using the existing procedure coded BLIMPJ. Modifications and innovations to the code are examined. Updated routines are listed.

Praharaj, S. C.↗
NASA NTRS1983

AOTV Low L/D Preliminary Aeroheating Design Environment

The aerothermal environment to a configuration with a brake face which exhibits a low lift to drag ratio (L/D) of below 0.75 is emphasized. The five times geosynchronous (5 x Geo) orbit entry was selected as the design trajectory. The available data base and math model is discussed. The resulting preliminary design environment is documented. Recommendations as to how the design environment may be improved through technological advances are given.

Engel, C. D.↗
NASA NTRS1983

MINIVER upgrade for the AVID system. Volume 1: LANMIN user's manual

The successful design of thermal protection systems for vehicles operating in atmosphere and near space environments requires accurate analyses of heating rate and temperature histories encountered along a trajectory. For preliminary design calculations, however, the requirement for accuracy must be tempered by the need for speed and versatility in computational tools used to determine thermal environments and structural thermal response. The MINIVER program has been found to provide the proper balance between versatility, speed and accuracy for an aerothermal prediction tool. The advancement in computer aided design concepts at Langley Research Center (LaRC) in the past few years has made it desirable to incorporate the MINIVER program into the LaRC Advanced Vehicle Integrated Design, AVID, system. In order to effectively incorporate MINIVER into the AVID system, several changes to MINIVER were made. The thermal conduction options in MINIVER were removed and a new Explicit Interactive Thermal Structures (EXITS) code was developed. Many upgrades to the MINIVER code were made and a new Langley version of MINIVER called LANMIN was created. The theoretical methods and subroutine functions used in LANMIN are described.

Engel, C. D.↗
NASA NTRS1983

MINIVER upgrade for the AVID system. Volume 2: LANMIN input guide

In order to effectively incorporate MINIVER into the AVID system, several changes to MINIVER were made. The thermal conduction options in MINIVER were removed and a new Explicit Interactive Thermal Structures (EXITS) code was developed. Many upgrades to the MINIVER code were made and a new Langley version of MINIVER called LANMIN was created. A user input guide for LANMIN is provided.

Engel, C. D.↗
NASA NTRS1983

Low L/D aerobrake test at Mach 10

An aerobraking Orbital transfer vehicle may be used to increase the Space Shuttle mission capability to and from high orbits. A Mach 10 wind-tunnel test was performed for a low lift-drag aerobrake, to define a preliminary aerothermal environment for this candidate concept. Test hardware simulated the ribs and stretched fabric of conceptual flight hardware. Pressures, paint-melting histories, and oilflow data were measured on the brake. Pressure and thermocouple heating rate data were measured on the payload. Brake peak heating is at the edge at all angles of attack, although the stagnation point is not outboard of 75 percent radius even at 20 degrees angle of attack. Brake ribs show slightly higher heating than flats, although pressures are essentially constant. Payload peak heating occurs near 12 degrees angle of attack, and is 30 percent of the sphere stagnation point heating (for a sphere of brake diameter). Payload pressure distributions follow the heating pattern. Reynolds number effects are small on the brake and large on the payload, for the range of test conditions: 0.4-1.0 million/foot.

Hair, L. M.↗
NASA NTRS1982

Initial Shuttle external tank flight evaluation

The objective of this paper is to evaluate aerothermal flight measurements made on the Space Shuttle External Tank (ET) during its initial flights. The ETs have been adequately instrumented to measure various quantities during flight including heat transfer, pressure, and structural temperature. The flight data have been compared with mathematical models based on an extensive wind tunnel data base, realistic flowfields, and empirical heat-transfer relationships. An analysis of the results points out the validity of the current aeroheating methodology and existing data base, and identifies problem areas in the methodology as indicated by the flight data.

Praharaj, S. C.↗
NASA NTRS1980

Wake flowfields for Jovian probe

The wake flow field developed by the Galileo probe as it enters the Jovian atmosphere was modeled. The wake produced by the probe is highly energetic, yielding both convective and radiative heat inputs to the base of the probe. A component mathematical model for the inviscid near and far wake, the viscous near and far wake, and near wake recirculation zone was developed. Equilibrium thermodynamics were used for both the ablation and atmospheric species. Flow fields for three entry conditions were calculated. The near viscous wave was found to exhibit a variable axial pressure distribution with the neck pressure approximately three times the base pressure. Peak wake flow field temperatures were found to be in proportion to forebody post shock temperatures.

Engel, C. D.↗
NASA NTRS1979

Tumbling-vehicle entry heating

Programs rapidly determines heating rate for any point on vehicle at any angle of attack or roll position during reentry into earth's atmosphere. Package can be used to accurately find heating environment for numerous points on vehicle as function of time for thermal protection systems or structural breakup studies.

Engel, C. D.↗
NASA NTRS1979

Jovian probe wake flowfield

The base heating problem in the Jovian probe was examined. The entire wake flowfield is defined to calculate the radiative heating to the base region of the Jovian probe. Engineering tools for calculating the probe's wake flowfield are developed. The near and far viscous and inviscid flowfields for three entry conditions are calculated. The flowfields include pressure, temperature, and species concentration for radiation analysis. A mathematical model used in the calculations is described. The results obtained indicate that temperatures in the Jovian probe range from 4,000 to 10,00 K and pressures range from 10 to 1,000 times the free stream value.

Engel, C. D.↗
NASA NTRS1979

Aerodynamic heating to representative SRB and ET protuberances

Heating data and data scaling methods which can be used on representative solid rocket booster and external tank (ET) protuberances are described. Topics covered include (1) ET geometry and heating points; (2) interference heating test data (51A); (3) heat transfer data from tests FH-15 and FH-16; (4) individual protuberance data; and (5) interference heating of paint data from test IH-42. A set of drawings of the ET moldline and protuberances is included.

Engel, C. D.↗
NASA NTRS1979

External tank laminar and rarefied aeroheating

A practical method has been developed for calculation of laminar and rarefied aerodynamic heating to the external tank of the Space Shuttle during the ascent phase of flight. A modification of laminar boundary theory is used as the basis for the heating relation. This relation is used in conjunction with a correlation for surface pressures to obtain undisturbed aerodynamic heating. Interference effects on the external tank due to the orbiter are correlated using the rarefaction parameter which was developed as part of the heating relation. The effects of rarefaction on the undisturbed and interference heating are illustrated with test data.

Engel, C. D.↗
NASA NTRS1974

Radiation-gas dynamic shock layer coupling

The present work considers theoretically the problem of radiation losses on the shock layer during hypersonic flight, and in particular, results are presented for the stagnation line shock layer for a wide variety of flight conditions, providing a new overview of radiation-gas dynamic coupling within a shock layer. The present results are based on a previous model (Engel, Farmer, et al., 1973) of a viscous radiating shock layer. An important result is that the radiation-gas dynamic coupling effect on the radiative heating can be related to a single parameter, namely, the radiative cooling parameter, whereas the effect on the shock layer thickness is not a simple function of this parameter.

Engel, C. D.↗
NASA NTRS1974

Booster aerodynamic heating: Test support

Several technical areas were encompassed in providing support for booster thermal environment test work. These areas included: (1) cavity flow heating, (2) rarefied flow heating, and (3) impulse operated model research and testing. Cavity flow heating problems were studied with respect to the proposed altitude control motors for the space shuttle. Available literature on this subject was reviewed and analytical predictive methods were summarized for use in planning testing work. Rarefied flow heating data was reviewed and correlated. The study showed the importance of considering rarefied flow conditions in launch thermal environment prediction. Impulse operated model research and testing was conducted to provide a basis for understanding and designing such models for booster thermal environment testing.

Engel, C. D.↗
NASA NTRS1973

Ablation and radiation coupled viscous hypersonic shock layers.

Coupled ablator shock layer solutions for the stagnation point are presented for typical hyperbolic entry atmospheric flight conditions. These solutions were obtained by numerically solving the stagnation line shock layer equations and quasi-steady ablator equations. These equations included ablation and radiation coupling within the viscous shock layer, line and continuum radiation for both air and phenolic-nylon ablation species and local thermodynamic equilibrium throughout. The results presented provide a sound basis for understanding many of the processes characteristic of hypersonic shock layer heating.-

Engel, C. D.↗
NASA NTRS1971

Ablation and radiation coupled viscous hypersonic shock layers, volume 1

The results for a stagnation-line analysis of the radiative heating of a phenolic-nylon ablator are presented. The analysis includes flow field coupling with the ablator surface, equilibrium chemistry, a step-function diffusion model and a coupled line and continuum radiation calculation. This report serves as the documentation, i e. users manual and operating instructions for the computer programs listed in the report.

Engel, C. D.↗