Search NASA⌕ Search

Engineering topics

Engtrakul, Chaiwat

Publications and source records attributed to Engtrakul, Chaiwat.

12 records
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Characterization of pitch carbon coating properties affecting the electrochemical behavior of silicon nanoparticle lithium-ion battery anodes

Silicon is an exciting material for next-generation lithium-ion battery anodes, due to its high theoretical capacity and availability, but its widespread implementation has been limited by extensive volume changes during cycling that causes mechanical damage and limits cycle life. One approach to mitigating these deleterious effects while still maintaining silicon's benefits is the addition of a pitch carbon coating to nanometer-sized silicon particles. Here, in this study, we present characterization of pitch-coated silicon electrodes without annealing and annealed at 700 °C and 1000 °C to determine the optimum temperature treatment, as well as pitch-only and silicon-only electrodes with and without annealing to elucidate the impacts of each component on early electrochemical behavior. Using Fourier transform infrared and Raman spectroscopies, atomic force and scanning spreading resistance microscopy, and electrochemical analysis, we find 700 °C to be the optimal annealing temperature, as amorphous carbon is created, which improves conductivity prior to cycling and facilitates ion storage during cycling that increases capacity. We also present in situ Raman spectroscopy data demonstrating the heterogeneous aging that occurs across the electrode surface during cycling.

25 ENERGY STORAGE↗
DOE OSTI2024

"Soiling, Cleaning, and Abrasion: The Results of the Five-Year Photovoltaic Glass Coating Field Study" [Slides]

External contamination ("soiling") of the incident surface is a major limiting factor for solar technologies. A 5-year field glass coupon study was conducted to better understand external contamination and its effects; compare cleaning methods and the use of preventative coatings; and explore the abrasion resulting from cleaning to advise on accelerated abrasion testing. Test sites included the cities of Dubai (UAE), Kuwait City (Kuwait), Mesa (AZ), Mumbai (India), and Sacramento (CA). Through the 5-year cumulative study, dry brush, water spray, and wet sponge and squeegee cleaning methods were compared to no cleaning. Optical microscopy was used to obtain images, including representative color images, grayscale images for object analysis, and oblique images for coating integrity assessment. A thresholding protocol was developed to analyze and distinguish specimens using the ImageJ software. Optical performance was quantified using a spectrophotometer, including comprehensive optical characterization (transmittance, reflectance, and absorptance in addition to forward- and back-scattering). Atomic force microscopy was used to verify the abrasion damage morphology, including the width and depth of surface scratches. Analysis of the results included correlation of optical performance and particle area coverage, rank order (by coating or location), and the acceleration factor for abrasion damage. The efficacy of external cleaning was more readily distinguished from the effectiveness of antisoiling coatings. The acceleration factor for dry brush cleaning of a porous silica coating was found to be on the order of unity.

14 SOLAR ENERGY↗
DOE OSTI2023

NREL 25-cm2 High-Pressure Low-Temperature Electrolysis Cell Hardware (Open Source)

This data resource describes an open-source cell hardware that enables low temperature electrolysis (LTE) testing at elevated pressures. Existing commercial options have several downsides when it comes to R&D testing. They are often not designed for repeated reassembly, may not be able to accommodate porous transport layers with different thicknesses, and do not give state-of-the-art performance. Therefore, this hardware was developed specifically with LTE R&D in mind and its design is being made available to the global LTE community. This work was planned and funded by the U.S. Department of Energy's H2NEW consortium (https://h2new.energy.gov/). The hardware design package (.zip file) details the drawings, auxiliary materials, and procedures required to fabricate, assemble, and operate the National Renewable Energy Laboratory's (NREL's) high-pressure low-temperature electrolysis cells. While the hardware itself—end plates, current collectors, flow fields, bolts and washers, tube fittings—is always the same, the assembly and operating procedures may change depending on the active materials being tested, especially for the membrane. Material-specific assembly and operating procedures will be posted to the H2NEW website as they are developed and validated. Disclaimer: The documents and drawings included in this download package describe a design for a low temperature electrolysis hardware that is intended to comply with leak testing according to ASME B31.1. Safe operation at ambient and elevated pressures is the sole responsibility of the end user, which should be evaluated on a case-by-case basis for each individual cell. Factors affecting the sealing capability may depend on, for example, machining quality, cell assembly components, operating conditions, and operating history. Operation at pressure should only be performed on qualified test stands by qualified operators. NREL/ALLIANCE FOR SUSTAINABLE ENERGY, LLC/DOE DISCLAIM ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING THE WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, AND MAKES NO WARRANTY AS TO THE ACCURACY, COMPLETENESS, OR USEFULNESS OF ANY INFORMATION PROVIDED HEREIN. USE OF THIS PACKAGE IS AT THE USER’S OWN RISK.

08 HYDROGEN↗
DOE OSTI2023

Crosslinking of loose insulating powders

Described herein are materials and methods useful in the field of insulation, including building materials, refrigeration, cryogenics, and shipping, amongst others. Advantageously, the provided materials and method provide low thermal conductivities and increased mechanical strength, allowing for efficient insulating in a diverse range of applications. The provided materials and methods include individual particles connected by a polymer network that links individual particles and may include hollow or evacuated capsules and various strengthening agents.

Simpson, Lin Jay↗
DOE OSTI2023

Pitch Carbon-coated Ultrasmall Si Nanoparticle Lithium-ion Battery Anodes Exhibiting Reduced Reactivity with Carbonate-based Electrolyte

Silicon anodes for lithium-ion batteries (LIBs) have the potential for higher energy density compared to conventionally used graphite-based LIB anodes. However, silicon anodes exhibit poor cycle and calendar lifetimes due to mechanical instabilities and high chemical and electrochemical reactivity with the carbonate-based electrolytes that are typically used in LIBs. In this work, we synthesize a pitch carbon-coated silicon nanoparticle composite active material for LIB anodes that exhibits reduced chemical reactivity with carbonate-based electrolytes compared to an uncoated silicon anode. Silicon primary particle sizes less than 10 nm diameter minimize micro-scale mechanical degradation of the anode composite, while conformal coatings of pitch carbon minimize the parasitic reactions between the silicon and the electrolyte. When matched with a high voltage NMC622 (LiNi 0.6 Mn 0.2 Co 0.2 O 2 ) cathode, the pitch carbon-coated silicon anode retains approximately 75% of its initial capacity at the end of 1000 cycles. Increasing the areal loading of the pitch carbon-coated silicon anodes to realize energy density improvements over graphite anodes results in severe mechanical degradation on the electrode level, highlighting a remaining challenge to be addressed in future work.

25 ENERGY STORAGE↗
DOE OSTI2022

The Role of Oxygen in Lithiation and Solid Electrolyte Interphase Formation Processes in Silicon-Based Anodes

Silicon oxides (SiO x ) have been considered as promising alternatives to pure Si in high energy anodes in lithium-ion batteries (LIBs) due to their improved cycling stability. However, their fundamental lithiation mechanism has not yet been systematically investigated, and potential collateral downsides remain unclear. In this work, we report on the role of oxygen in lithiation/delithiation and solid electrolyte interphase (SEI) formation processes in SiO x thin film model electrodes with different oxygen contents. Here, we show that the SiO x anodes with higher oxygen content experience smaller volume change and form a thinner and more stable SEI, both of which are beneficial for cycling stability. However, these SiO x anodes also show an irreversible lithiation at around 0.7 V attributed to the reduction of Si oxides, leading to lower first cycle coulombic efficiency that is undesirable for practical applications. Overall, these results offer a balanced perspective on the advantages and disadvantages that oxygen brings to Si-based anodes in LIBs.

25 ENERGY STORAGE↗
DOE OSTI2022

Photovoltaic windows cut energy use and CO 2 emissions by 40% in highly glazed buildings

Buildings account for 30% of global energy use. The architectural trend across building sectors is toward more glass despite higher energy use and carbon emissions than opaque cladding alternatives. Numerous window technologies - low-emissivity coatings, triple glazing, dynamic tinting, and the more recently developed photovoltaic glass - have emerged in the last two decades as approaches to reduce building energy. However, a comprehensive understanding of where and how these window technologies can be installed to enable optimal energy savings under different climate conditions remains limited. Here we test window technologies using thousands of macroscale building-energy simulations for different climate zones and building designs to evaluate the associated net energy use and carbon-emissions reduction potential. Novel window technologies, especially photovoltaic windows with high thermal performance, offer energy savings in all climates, ranging from 10,000-40,000 GJ per year over substandard windows for a typical office building, resulting in up to 2,000 tons of annual CO 2 emissions reduction. Highly glazed, net-zero buildings are achievable via photovoltaic windows when combined with careful geometric considerations.

14 SOLAR ENERGY↗
DOE OSTI2022

Catalytic hot-gas filtration of biomass pyrolysis vapors

The present disclosure relates to a device that includes a filter element and a catalyst, where the filter element is configured to remove particulate from a stream that includes at least one of a gas and/or a vapor to form a filtered stream of the gas and/or the vapor, the catalyst is configured to receive the filtered stream and react a compound in the filtered stream to form an upgraded stream of the gas and/or the vapor, further including an upgraded compound, and both the filter element and the catalyst are configured to be substantially stable at temperatures up to about 500° C.

Magrini, Kimberly A.↗
DOE OSTI2021

Novel Semi-Rigid Capsule Insulation Demonstration (CRADA CRD-18-00769 Final Report)

This effort probed the novel use of capsule insulation to form an effective “solid” (as compared to powder) insulating “blanket,” “panel,” or other useful structures and to demonstrate important technical achievements, including crosslinking, thermal conductivity measurements, and achieving appropriate thermal and other properties needed to form high quality insulation that can directly and cost effectively address such markets as cryogenics and highly insulating panels.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Transparent and insulating materials having evacuated capsules

Transparent and insulating materials having evacuated capsules are provided. According to an aspect of the invention, a method includes forming evacuated capsules within a solution, and dispersing and suspending the evacuated capsules within the solution such that a packing density of the evacuated capsules within the solution is greater than 30%, and a visible light transmission of the solution including the evacuated capsules is greater than 75%. According to another aspect of the invention, a layer includes a plurality of evacuated capsules distributed within a dried sol-gel. A thermal conductivity of the layer is between 0.02 W/m-K and 0.001 W/m-K, and the layer has a visible light transmission of greater than 30%.

Simpson, Lin Jay↗