Engineering topics

Ercegovic, D. B.

Publications and source records attributed to Ercegovic, D. B..

6 records

NASA NTRS1986

Composite Refractory Felt/Ceramic Material

Ceramic protective coatings on combustor liners adhere better. Report discloses results of recent combustor-liner research where thick yttria stabilized zirconia ceramic was plasma-sprayed on BRUNSBOND substrates and exposed to nearly stoichiometric combustion. Combustor screening tests exposed 30 test specimens to nearly-stoichiometric flame temperatures of 3,450 degrees F (2,170 K) for 4 cycles. After completion of screening tests, all 30 specimens showed no visible evidence of discoloration or failure. There were no mudflat cracks, felt/ceramic, or backing/felt separations on any panels.

Ercegovic, D. B.↗

NASA NTRS1984

Ceramic composite liner material for gas turbine combustors

Advanced commercial and military gas turbine engines may operate at combustor outlet temperatures in excess of 1920 K (3000 F). At these temperatures combustors liners experience extreme convective and radiative heat fluxes. The ability of a plasma sprayed ceramic coating to reduce liner metal temperature has been recognized. However, the brittleness of the ceramic layer and the difference in thermal expansion with the metal substrate has caused cracking, spalling and some separation of the ceramic coating. Research directed at turbine tip seals (or shrouds) has shown the advantage of applying the ceramic to a compliant metal pad. This paper discusses recent studies of applying ceramics to combustor liners in which yttria stabilized zirconia plasma sprayed on compliant metal substrates which were exposed to near stoichiometric combustion, presents performance and durability results, and describes a conceptual design for an advanced, small gas turbine combustor. Test specimens were convectively cooled or convective-transpiration cooled and were evaluated in a 10 cm square flame tube combustor at inlet air temperatures of 533 K (500 F) and at a pressure of 0.5 MPa (75 psia). The ceramics were exposed to flame temperatures in excess of 2000 K (3320 F). Results appear very promising with all 30 specimens surviving a screening test and one of two specimens surviving a cyclic durability test.

Ercegovic, D. B.↗

NASA NTRS1984

Ceramic composite liner material for gas turbine combustors

The application of ceramics to gas turbine combustor liners to reduce liner metal temperature was studied in an experiment in which yttria-stabilized zirconia plasma was sprayed on compliant metal substrates exposed to near stoichiometric combustion. The strain isolation pad materials chosen were Hoskins Alloy 875 and BRUNSLLOY 534 Fiber Metal of 0.25 and 0.38 cm thicknesses and 35 and 45 percent density levels. Combustor screening tests of all specimens showed no evidence of deterioration or failure. Specimens exposed to flame temperatures in excess of 2100 K were convectively or convective-transpiration cooled and were evaluated in a 10 cm sq flame tube at inlet air temperature of 533 K and pressure of 0.5 MPa. The results suggest the superiority of a system composed of the Hoskins Alloy 875 compliant pad with 0.25 cm thickness and 35 percent density coupled with a NiCrAlY bond coat and a 8 percent Y2O3-ZrO2 ceramic top coat of 0.19 cm thickness.

Ercegovic, D. B.↗

NASA NTRS1983

Combustion hot section technology

The overall objective of the Turbine Engine Hot Section Technology Combustion Project is to develop and verify improved and more accurate analysis methods for increasing the ability to design with confidence the combustion system for advanced aircraft turbine engines. The analysis methods developed will be generically applicable to combustion systems and not restricted to one specific engine or manufacturer. This project's approach was to first assess and evaluate existing combustor aerothermal analysis models by means of a contracted effort initiated during FY 1982. This evaluation effort has assessed and quantified known models' strengths and deficiencies. During FY 1984 the Aerothermal Modeling Program, Phase 2 will be initiated, which is expected to have contracted model development efforts in the areas of improved numerical methods for turbulent viscous flows, flow interactions, and fuel spray flow foekd interactions. A Phase 3 effort is planned to address remaining model deficiencies. The primary inhouse effort in this area will be the determination of high pressure flame radiation characteristics in a full annular combustor. This experiment will be conducted in the NASA LeRC High Pressure Facility with the results compiled into a comprehensive flame radiation and liner heat flux model.

Ercegovic, D. B.↗

NASA NTRS1982

Combustion hot section technology

The Turbine Engine Hot Section Technology Combustion Program is briefly described. The overall objective of the project is to develop and verify improved and more accurate analysis methods for increasing the ability to design with confidence the combustion system for advanced aircraft turbine engines. The approach is to first assess and evaluate existing combustor aerothermal analysis models by means of a contracted effort initiated during FY-82. The program also includes both analytical and experimental research efforts in the areas of aerothermal modeling and liner cyclic life. It is expected that the combustor model development effort will generate improved understanding in the areas of high pressure flame radiation characteristics, model numerical methods and solution schemes, complex geometrical boundary conditions, fuel spray - flow field interactions, combustion kinetics, flow and mixing of dilution jets, turbulence and heat transfer, and soot and carbon formation.

Ercegovic, D. B.↗

NASA NTRS1979

Effect of swirler-mounted mixing venturi on emissions of flame-tube combustor using jet A fuel

Six headplate modules in a flame-tube combustor were evaluated. Unburned hydrocarbons, carbon monoxide, and oxides of nitrogen were measured for three types of fuel injectors both with and without a mixing venturi. Tests were conducted using jet A fuel at an inlet pressure of 0.69 megapascal, an inlet temperature of 478 K, and an isothermal static pressure drop of 3 percent. Oxides of nitrogen were reduced by over 50 percent with a mixing venturi with no performance penalties in either other gaseous emissions or pressure drop.

Ercegovic, D. B.↗