How to get noWear? – A new take on the design of in-situ formed high performing low-friction tribofilms
Not Available
Engineering topics
Publications and source records attributed to Erdemir, A..
Not Available
Polyalkylene glycols (PAG) have been explored as a possible base stock for engine oil formulation. The friction, wear, and load-carrying capacity of five different PAG chemistries were evaluated either as a base stock or as formulated oils in pure sliding and sliding-rolling conditions using various laboratory bench test rigs operating under boundary and mixed lubrication regimes. The results were compared against GF-5 SAE 5W-20 and a mineral-based oil. The wear surfaces were also characterized using various surface-sensitive techniques for analysis of tribofilms to understand the mechanism of friction reduction. The results indicated that PAG oils show lower friction/traction coefficients and improved load-carrying capability, depending on the formulation, than those of the GF-5 SAE 5W-20 and mineral-based oil. The adsorption of PAG molecules on the surface appeared to be responsible for the lower friction characteristics.
This paper presents an experimental study of friction and wear performance of quaternary CrSiCN coatings deposited on a hardened H-13 steel substrate by a plasma enhanced magnetron sputtering (PEMS) technique. Friction and wear tests were conducted with a reciprocating line contact between a hardened 4370 steel roller and coated and uncoated flat specimens under dry and lubricated conditions. The effects of coating thickness (1, 3.5 and 7.5 μm) on the mechanical properties, friction and wear performance were also assessed. In dry sliding, the friction of coated surfaces was about the same as for uncoated surfaces, except for the 1-μm coating, which had higher friction. Friction for coated surfaces under lubricated contact was in general higher than for uncoated surfaces. There was no measurable wear on any of the coated surfaces, under either dry or lubricated conditions. However, wear was higher on the steel roller counterface sliding against the coated surfaces, with the amount of wear proportional to the mating coating thickness. The effectiveness of formulated lubricant additives was also modified by the coating, resulting in major effects on friction and wear behavior. Finally, this reduction in lubricant additive efficacy is due to the fact that the additives were designed and optimized for ferrous surfaces.
Changing the surface texture of sliding surfaces is an effective way to manipulate friction and wear of lubricated surfaces. Having realized its potential, we have done very extensive studies on the effects of laser surface texturing (LST, which involves the creation of an array of microdimples on a surface) on friction and wear behavior of oil-lubricated steel surfaces in the early 2000s. In this paper, we reviewed some of our research accomplishments and assessed future directions of the laser texturing field in many diverse industrial applications. Our studies specifically addressed the impact of laser texturing on friction and wear of both the flat conformal and initial non-conformal point contact configurations using a pin-on-disk test rig under fully-flooded synthetic oil lubricants with different viscosities. Electrical resistance measurement between pin and LST disks was also used to determine the operating lubrication regimes in relation to friction. In conformal contact, we confirmed that LST could significantly expand the operating conditions for hydrodynamic lubrication to significantly much higher loads and slower speeds. In particular, with LST and higher viscosity oils, the low-friction full hydrodynamic regime was shifted to the far left in the Stribeck diagram. Overall, the beneficial effects of laser surface texturing were more pronounced at higher speeds and loads and with higher viscosity oil. LST was also observed to reduce the magnitude of friction coefficients in the boundary regime. For the non-conformal contact configuration, we determined that LST would produce more abrasive wear on the rubbing counterface compared to the untreated surfaces due to a reduction in lubricant fluid film thickness, as well as the highly uneven and rough nature of the textured surfaces. However, this higher initial wear rate has led to faster generation of a conformal contact, and thus transition from the high-friction boundary to lower friction mixed lubrication regime, resulting in a rapid reduction in the friction coefficient with increased ball wear. Higher density of LST, lower oil viscosity, and hardness of counterface steel surface facilitate an increase of the initial wear, which promotes friction reduction. This phenomenon can be beneficial if the initial accelerated wear on the counterface is acceptable in intended applications. This paper summarizes our experimental investigation of the effect of LST on friction properties and lubrication regime transitions in a unidirectional sliding contact.
Abstract Hydrogenated diamond like Carbon (H-DLC) is a promising lubricious coating that attracted a great deal of interest in recent years mainly because of its outstanding tribological properties. In this study, the nano-mechanical and -tribological properties of a range of H-DLC films were investigated. Specifically, four kinds of H-DLC coatings were produced on Si substrates in pure acetylene, pure methane, 25% methane + 75% hydrogen, 50% methane + 50% hydrogen discharge plasmas using a plasma enhanced chemical vapour deposition (PECVD) system. Nano indentation was performed to measure the mechanical properties such as hardness and young's modulus and nanoscartching was performed to investigate the frictional behavior and wear mechanism of the H-DLC samples in open air. Moreover, Vickers indentation method was utilized to assess the fracture toughness of the samples. The results revealed that there is a strong correlation between the mechanical properties (hardness, young's modulus, fracture toughness) and the friction coefficient of DLC coatings and the source gas chemistry. Lower hydrogen to carbon ratio in source gas leads to higher hardness, young's modulus, fracture toughness and lower friction coefficient. Furthermore, lower wear volume of the coated materials was observed when the friction coefficient was lower. It was also confirmed that lower hydrogen content of the DLC coating leads to higher wear resistance under nanoscratch conditions.
Not Available
Both helical and inclined columnar Si–10 at.% Cu structured thin films were deposited on Cu substrates using glancing angle deposition (GLAD) technique. In order to deposit Cu and Si two evaporation sources were used. Ion assistance was utilized in the first 5 min of the GLAD to enhance the adhesion and the density of the films. These films were characterized by thin film XRD, GDOES, SEM, and EDS. Electrochemical characterizations were made by testing the thin films as anodes in half-cells for 100 cycles. The results showed that the columnar SiCu thin film delivered 2200 mAh g -1 , where the helical one exhibited 2600 mAh g -1 , and, their initial coulombic efficiencies were found to be 38%–50% respectively. For the columnar and the helical thin film anodes, sustainable 520 and 800 mAh g -1 with 90% and 99% coulombic efficiencies were achieved for 100 cycles. These sustainable capacities showed the importance of the thin film structure having nano-sized crystals and amorphous particles. The higher surface area of the helices increases the capacity of the electrode because the contact area of the thin film anode with Li ions is increased, and the polarization which otherwise forms on the anode surface due to SEI formation is decreased. In addition, because of larger interspaces between the helices the ability of the anode to accommodate the volumetric changes is improved, which results in a higher coulombic efficiency and capacity retention during cycling test.
Explore the source record for details and available documents.
The rolling contact fatigue (RCF) characteristics of an aerospace bearing steel 440C coated with TiN films of various thicknesses are studied. The wear and corrosion properties of the film-substrate system are examined as well as how these properties correlate with the RCF behavior. It is found that TiN coatings with thicknesses below 1 micron resulted in significant improvements in the RCF lives of base steel substrates under both mild and heavy loading conditions.
The resistance of copper and TiN coatings on various bearing substrates to high-load rolling contact fatigue (RCF) is investigated. Special attention is given to the lubricating characteristics of copper deposited by ion plating, and the wear resistant characteristics of TiN deposited by ion plating and magnetron sputtering techniques. RCF samples of 440C and AMS 5749 bearing steels were coated. Sputter deposited and ion plated films were on the RCF samples in a range of thickness from about 2000 A to 2 microns. Results showed a marked improvement of the RCF for pure copper tested on 440C, but a degradation for copper on AMS 5749. It is also found that the 2000 A TiN films behave favorably on the 440C and AMS 5749 bearing steels at RCF stress levels of 786 ksi. Scanning electron microscopy, X-ray diffraction, and electron spectroscopy for chemical analysis were used during the investigation.