Search NASA⌕ Search

Engineering topics

Erdman, III, Donald L.

Publications and source records attributed to Erdman, III, Donald L..

On the correlation between the stress exponent for creep determined by nanoindentation and the mechanism of action enabling stress relief in indium

Instrumented indentation performed at room temperature with a Berkovich and 10 μm radius sphere has been used to measure the stress exponent for creep before and after the strain burst observed in well-annealed, high-purity indium. Before the strain burst, the measured values are successfully rationalized using a new model based on stress directed diffusional flow along the interface between the indenter tip and test specimen. After the strain burst, the measured stress exponents are found to be representative of dislocation glide and climb assisted glide. Here these results are compared and contrasted to the previous experimental investigations and modeling efforts of Feng et al., Lucas et al., and Li et al. Collectively, the experimental observations and rationalization presented here provide significant new insight into the mechanisms of action that control the competition for stress relief in small, constrained volumes of crystalline metals subjected to high homologous temperatures.

36 MATERIALS SCIENCE↗

Laser nanostructured surface preparation for joining materials

A joined article includes a first component having a laser-treated surface portion and a second component having a laser-treated surface portion. An adhesive joins the first component to the second component at the treated surface portion. A method of making a joined article form components and a system for making joined articles are also disclosed.

Sabau, Adrian Stefan↗

Continuous fiber malleable thermoset composites with sub-1-minute dwell times; validation of impact performance and evaluation of the efficacy of the compression forming process. CRADA Final Report

Mallinda is developing polyimine malleable thermoset prepreg composite materials which have excellent mechanical properties (100 GPa tensile modulus, 2 GPA tensile strength, 2.4% elongation at break) and high operating temperatures (Tg>200°C). At scale, polyimine resins are commensurate in price with commodity epoxy resins. What distinguishes malleable thermoset prepreg from traditional thermoset prepreg materials, is that they are fully cured during Mallinda’s roll-to-roll production of prepreg laminate. This results in 5 key value-differentiating benefits. First, it simplifies manufacturing logistics by enabling ambient transportation and storage, and by significantly extending out-life and shelf-life almost indefinitely. Second, elimination of autoclave curing reduces the economic and energy costs to the customer. Third, scrap rates can be reduced as malleable thermoset prepreg materials are directly reusable. Fourth, the manufacturing consolidation step can be roughly 10x faster than traditional thermosets, because the resin is already cured. Parts can be made via compression forming by the application of heat and pressure to quickly vitrify and consolidate a multilayer part – easily leading to sub 3-minute cycle times (at lab scale we have demonstrated a 20 second dwell time, with room for further optimization). Finally, the closed-loop cradle-to-cradle solution-based recyclability of malleable thermoset composites can also contribute significantly to the future of sustainable lightweight materials. The focus of this project was the development, optimization and validation of malleable thermoset composite materials which exhibit manufacturing cycle times of 3-minute or less, high speed impact performance on par with incumbent technologies, and defect-free consolidation of 3 dimensional parts.

36 MATERIALS SCIENCE↗

Laser nanostructured surface preparation for joining materials

A joined article includes a first component having a laser-treated surface portion and a second component having a laser-treated surface portion. An adhesive joins the first component to the second component at the treated surface portion. A method of making a joined article form components and a system for making joined articles are also disclosed.

Sabau, Adrian Stefan↗

The shear fracture toughness, K IIc , of graphite

In this study, the critical shear stress intensity factor, K IIc , here-in referred to as the shear fracture toughness, K IIc (MPa m), of two grades of graphite are reported. The range of specimen volumes was selected to elucidate any specimen size effect, but smaller volume specimen tests were largely unsuccessful, shear failure did not occur between the notches as expected. This was probably due to the specimen geometry causing the shear fracture stress to exceed the compressive failure stress. In subsequent testing the specimen geometry was altered to reduce the compressive footprint and the notches (slits) made deeper to reduce the specimen's ligament length. Additionally, we added the collection of Acoustic Emission (AE) during testing to assist with the identification of the shear fracture load. The means of K IIc from large specimens for PCEA and NBG-18 are 2.26 MPa m with an SD of 0.37 MPa m and 2.20 MPa m with an SD of 0.53 MPa m, respectively. The value of K IIc for both graphite grades was similar, although the scatter was large. In this work we found the ratio of K IIc / K Ic ≈ 1.6. .

36 MATERIALS SCIENCE↗

Understanding the Role of Hot Isostatic Pressing Parameters on the Microstructural Evolution of Ti-6Al-4V and Inconel 718 Fabricated by Electron Beam Melting

In this project, Avure and ORNL evaluated the influence of hot isostatic pressing (HIP) and thermal cycling as standalone post processing techniques on the microstructure of electron beam powder bed deposited Ti-6Al-4V and Inconel 718 alloys. Electron beam powder bed deposition is an effective technology for fabricating complex net shape components that cannot be manufactured with conventional processes. However, material deposited by this technology results in columnar grain growth which is detrimental for many applications. For Ti-6Al-4V, it has been found that thermal cycling alone is not sufficient to breakdown the columnar microstructure that is typical of electron beam powder bed technology. HIP, on the other hand, has the potential to be an effective technique to break down the columnar microstructure of Ti-6Al-4V into a more equiaxed and refined β grain structure, and provide a more homogeneous microstructure compared to the thermally cycled samples. Overall, the project showed that hot isostatic pressing reduced/eliminated porosity in both Ti-6Al-4V and Inconel 718 However, based on the unique thermal cycle and the application of pressure in the HIP vessel, Ti-6Al-4V e-beam deposited microstructures were modified from columnar grain growth to equiaxed microstructures; a significant outcome to this collaboration. Inconel 718, on the other hand, shows no change in the macrostructure as a result of the current HIP cycle based on the thermal history, and would require further investigation. Though the results of HIP cycle were very good at changing the microstructure, further development in optimizing the post heat treatments and HIP cycles is required to improve mechanical properties.

36 MATERIALS SCIENCE↗

Improving Fatigue Performance of AHSS Welds

Reported herein is technical progress on a U.S. Department of Energy CRADA project with industry cost-share aimed at developing the technical basis and demonstrate the viability of innovative in-situ weld residual stresses mitigation technology that can substantially improve the weld fatigue performance and durability of auto-body structures. The developed technology would be cost-effective and practical in high-volume vehicle production environment. Enhancing weld fatigue performance would address a critical technology gap that impedes the widespread use of advanced high-strength steels (AHSS) and other lightweight materials for auto body structure light-weighting. This means that the automotive industry can take full advantage of the AHSS in strength, durability and crashworthiness without the concern of the relatively weak weld fatigue performance. The project comprises both technological innovations in weld residual stress mitigation and due-diligence residual stress measurement and fatigue performance evaluation. Two approaches were investigated. The first one was the use of low temperature phase transformation (LTPT) weld filler wire, and the second focused on novel thermo-mechanical stress management technique. Both technical approaches have resulted in considerable improvement in fatigue lives of welded joints made of high-strength steels. Synchrotron diffraction measurement confirmed the reduction of high tensile weld residual stresses by the two weld residual stress mitigation techniques.

42 ENGINEERING↗