Engineering topics

Erickson, G. E.

Publications and source records attributed to Erickson, G. E..

14 records

NASA NTRS1999

HSR Model Deformation Measurements from Subsonic to Supersonic Speeds

This paper describes the video model deformation technique (VMD) used at five NASA facilities and the projection moire interferometry (PMI) technique used at two NASA facilities. Comparisons between the two techniques for model deformation measurements are provided. Facilities at NASA-Ames and NASA-Langley where deformation measurements have been made are presented. Examples of HSR model deformation measurements from the Langley Unitary Wind Tunnel, Langley 16-foot Transonic Wind Tunnel, and the Ames 12-foot Pressure Tunnel are presented. A study to improve and develop new targeting schemes at the National Transonic Facility is also described. The consideration of milled targets for future HSR models is recommended when deformation measurements are expected to be required. Finally, future development work for VMD and PMI is addressed.

Burner, A. W.↗

NASA NTRS1999

Pressure-Sensitive Paint and Video Model Deformation Systems at the NASA Langley Unitary Plan Wind Tunnel

Pressure-sensitive paint (PSP) and video model deformation (VMD) systems have been installed in the Unitary Plan Wind Tunnel at the NASA Langley Research Center to support the supersonic wind tunnel testing requirements of the High Speed Research (HSR) program. The PSP and VMD systems have been operational since early 1996 and provide the capabilities of measuring global surface static pressures and wing local twist angles and deflections (bending). These techniques have been successfully applied to several HSR wind tunnel models for wide ranges of the Mach number, Reynolds number, and angle of attack. A review of the UPWT PSP and VMD systems is provided, and representative results obtained on selected HSR models are shown. A promising technique to streamline the wind tunnel testing process, Modern Experimental Design, is also discussed in conjunction with recently-completed wing deformation measurements at UPWT.

Erickson, G. E.↗

NASA NTRS1999

Pressure-Sensitive Paint and Video Model Deformation Systems at the NASA Langley Unitary Plan Wind Tunnel

Erickson, G. E.↗

NASA NTRS1990

Impact of nose-probe chines on the vortex flows about the F-16C

A 1/15-scale model of the F-16C aircraft was tested at subsonic and transonic speeds to determine the effects of small nose-probe chines on the high angle-of-attack aerodynamic and stability characteristics. Off-body flow visualization using a laser vapor screen technique and six-component forces and moments were obtained at freestream Mach numbers of 0.30, 0.60, and 0.80. The nose-probe chines generated strong vortices interacting with the vortices generated over the smooth forebody or over the strakes. These vortices in turn led to global flow unsteadiness and model dynamics at the high angles of attack. The test results underscore the sensitivity of the high angle-of-attack flow field to small geometry changes in the nose region.

Hall, R. M.↗

NASA NTRS1986

Water facilities in retrospect and prospect: An illuminating tool for vehicle design

Water facilities play a fundamental role in the design of air, ground, and marine vehicles by providing a qualitative, and sometimes quantitative, description of complex flow phenomena. Water tunnels, channels, and tow tanks used as flow-diagnostic tools have experienced a renaissance in recent years in response to the increased complexity of designs suitable for advanced technology vehicles. These vehicles are frequently characterized by large regions of steady and unsteady three-dimensional flow separation and ensuing vortical flows. The visualization and interpretation of the complicated fluid motions about isolated vehicle components and complete configurations in a time and cost effective manner in hydrodynamic test facilities is a key element in the development of flow control concepts, and, hence, improved vehicle designs. A historical perspective of the role of water facilities in the vehicle design process is presented. The application of water facilities to specific aerodynamic and hydrodynamic flow problems is discussed, and the strengths and limitations of these important experimental tools are emphasized.

Erickson, G. E.↗

NASA NTRS1985

Low-speed experimental study of the vortex flow effects of a fighter forebody having unconventional cross-section

A low speed wind tunnel investigation is conducted for the vortex flow characteristics of a tailless fighter configuration that features full length, fuselage-blended forebody strakes. Static pressure distributions were obtained on the forebody upper surface, and six-component forces and moments were measured on the complete, 60-deg cropped delta wing-fuselage-centerline vertical fin model at angles of attack and sideslip respectively reaching 50 deg and + or - 20 deg. The surface pressure data reveal that development of concentrated vortices from the sharp edged forebody strakes occurred at moderate and high angles of attack. The blended forebody was effective in capturing the windward vortical flow up to high incidence and sideslip angles. The direct suction effect of the windward vortex on the forebody sidewall was the primary contributor to static directional stability at high angles of attack. These improvements are potentially offset, however, by reduced or unstable roll and yaw damping.

Erickson, G. E.↗

NASA NTRS1984

Vortex Flap Technology: a Stability and Control Assessment

A comprehensive low-speed wind tunnel investigation was performed of leading edge vortex flaps applied to representative aircraft configurations. A determination was made of the effects of analytically- and empirically-designed vortex flaps on the static longitudinal and lateral-directional aerodynamics, stability, and control characteristics of fighter wings having leading-edge sweep angles of 45 to 76.5 degrees. The sensitivity to several configuration modifications was assessed, which included the effects of flap planform, leading- and trailing-edge flap deflection angles, wing location on the fuselage, forebody strakes, canards, and centerline and outboard vertical tails. Six-component forces and moments, wing surface static pressure distributions, and surface flow patterns were obtained using the Northrop 21- by 30-inch low-speed wind tunnel.

Carey, K. M.↗

NASA NTRS1983

Experimental investigation of forebody and wing leading-edge vortex interactions at high angles of attack

An experimental investigation was conducted to assess the vortex flow-field interactions on an advanced, twin-jet fighter aircraft configuration at high angles of attack. Flow-field surveys were conducted on a small-scale model in the Northrop 0.41 - by 0.60-meter water tunnel and, where appropriate, the qualitative observations were correlated with low-speed wind tunnel data trends obtained on a large-scale model of the advanced fighter in the NASA Langley Research Center 30- by 60-foot (9.1- by 18.3-meter) facility. Emphasis was placed on understanding the interactions of the forebody and LEX-wing vortical flows, defining the effects on rolling moment variation with sideslip, and identifying modifications to control or regulate the vortex interactions at high angles of attack. The water tunnel flow visualization results and wind tunnel data trend analysis revealed the potential for strong interactions between the forebody and LEX vortices at high angles of attack. In particular, the forebody flow development near the nose could be controlled by means of carefully-positioned radome strakes. The resultant strake-induced flow-field changes were amplified downstream by the more powerful LEX vortical motions with subsequent large effects on wing flow separation characteristics.

Erickson, G. E.↗

NASA NTRS1982

Water tunnel flow visualization and wind tunnel data analysis of the F/A-18

Six degree of freedom studies were utilized to extract a band of yawing and rolling moment coefficients from the F/A-18 aircraft flight records. These were compared with 0.06 scale model data obtained in a 16T wind tunnel facility. The results, indicate the flight test yawing moment data exhibit an improvement over the wind tunnel data to near neutral stability and a significant reduction in lateral stability (again to anear neutral level). These data are consistent with the flight test results since the motion was characterized by a relatively slo departure. Flight tests repeated the slow yaw departure at M 0.3. Only 0.16 scale model wind tunnel data showed levels of lateral stability similar to the flight test results. Accordingly, geometric modifications were investigated on the 0.16 scale model in the 30x60 foot wind tunnel to improve high angle of attack lateral stability.

Erickson, G. E.↗

NASA NTRS1979

Effects of spanwise blowing on the surface pressure distribution and vortex-lift characteristics of a trapezoidal wing-strake configuration

The effects of spanwise blowing on the surface pressures of a 44 deg swept trapezoidal wing-strake configuration were measured. Wind tunnel data were obtained at a free stream Mach number of 0.26 for a range of model angle of attack, jet thrust coefficient, and nozzle chordwise location. Results showed that spanwise blowing delayed the leading edge vortex breakdown to larger span distances and increased the lifting pressures. Vortex lift was achieved at span stations immediately outboard of the strake-wing junction with no blowing, but spanwise blowing was necessary to achieve vortex lift at increased span distances. Blowing on the wing in the presence of the strake was not as effective as blowing on the wing alone. Spanwise blowing increased lift throughout the angle-of-attack range, improved the drag polars, and extended the linear pitching moment to higher values of lift. The leading edge suction analogy can be used to estimate the effects of spanwise blowing on the aerodynamic characteristics.

Campbell, J. F.↗

NASA NTRS1977

Improvement of maneuver aerodynamics by spanwise blowing

Spanwise blowing was used to test a generalized wind-tunnel model to investigate component concepts in order to provide improved maneuver characteristics for advanced fighter aircraft. Primary emphasis was placed on performance, stability, and control at high angles of attack and subsonic speeds. Test data were obtained in the Langley high speed 7 by 10 foot tunnel at free stream Mach numbers up to 0.50 for a range of model angles of attack, jet momentum coefficients, and leading and trailing edge flap deflection angles. Spanwise blowing on a 44 deg swept trapezoidal wing resulted in leading edge vortex enhancement with subsequent large vortex induced lift increments and drag polar improvements at the higher angles of attack. Small deflections of a leading edge flap delayed these lift and drag benefits to higher angles of attack. In addition, blowing was more effective at higher Mach numbers. Spanwise blowing in conjunction with a deflected trailing edge flap resulted in lift and drag benefits that exceeded the summation of the effects of each high lift device acting alone. Asymmetric blowing was an effective lateral control device at the higher angles of attack.

Erickson, G. E.↗

NASA NTRS1977

Augmentation of maneuver performance by spanwise blowing

A generalized wind tunnel model was tested to investigate new component concepts utilizing spanwise blowing to provide improved maneuver characteristics for advanced fighter aircraft. Primary emphasis was placed on high angle of attack performance, stability, and control at subsonic speeds. Spanwise blowing on a 44 deg swept trapezoidal wing resulted in leading edge vortex enhancement with subsequent large vortex-induced lift increments and drag polar improvements at the higher angles of attack. Small deflections of a leading edge flap delayed these lift and drag benefits to higher angles of attack. In addition, blowing was more effective at higher Mach numbers. Spanwise blowing in conjunction with a deflected trailing edge flap resulted in lift and drag benefits that exceeded the summation of the effects of each high lift device acting alone. Asymmetric blowing was an effective lateral control device at the higher angles of attack. Spanwise blowing on the wing reduced horizontal tail loading and improved the lateral-directional stability characteristics of a wing-horizontal tail-vertical tail configuration.

Erickson, G. E.↗

NASA NTRS1975

Flow visualization of vortices locked by spanwise blowing over wings featuring a unique leading and trailing-edge flap system

Flow visualization studies were conducted to qualitatively determine the effects of active generation and augmentation of vortex flow over wings by blowing a discrete jet in a spanwise direction in the channel formed by extension of upper surface leading- and trailing-edge flaps. Spanwise blowing from a reflection plane over a rectangular wing was found to generate and lock a dual corotating vortex system within the channel and, at sufficient blowing rates, cause the separated flow off the upper end of the leading-edge flap to reattach to the trailing-edge flap. Test parameters included wing angle of attack, jet momentum coefficient, leading- and trailing-edge flap deflection angle, and jet location above the wing surface. Effects due to removal of the leading- and trailing-edge flap were also investigated.

Erickson, G. E.↗

NASA NTRS1975

Flow visualization of leading-edge vortex enhancement by spanwise blowing

Flow visualization studies were conducted in a small pilot wind tunnel to determine qualitative effects of blowing a discrete jet essentially parallel to the leading edge of a 45 deg-swept trapezoidal wing featuring leading- and trailing-edge flaps. Test parameters included wing angle-of-attack, jet momentum coefficient, leading- and trailing-edge flap deflections, and nozzle chordwise displacement. Results of this study indicate that blowing from a reflection plane over the wing enhances the leading-edge vortex and delays vortex bursting to higher angles-of-attack and greater span distances. Increased blowing rates decrease vortex size, growth rate, and vertical displacement above the wing surface at a given span station and also extend the spanwise effectiveness of lateral blowing. Deflection of a leading-edge flap delays the beneficial effects of spanwise blowing to higher angles-of-attack. Nozzle chordwise locations investigated for the wing with and without leading-edge flap deflection appear equally effective in enhancing the separated leading-edge flow.

Erickson, G. E.↗