Search NASA⌕ Search

Engineering topics

Erik J. Stalcup

Publications and source records attributed to Erik J. Stalcup.

8 records
All sourcesNASA NTRSDOE OSTI
NASA NTRS2022

Aerospace Regenerative Fuel Cell Fluidic Component Design Challenges

A discrete regenerative fuel cell (RFC) system is currently under development at the NASA Glenn Research Center and Johnson Space Center. The objective of this activity is to produce an energy storage system with a higher specific energy (W·hr/kg) than the state-of-the-art battery technologies then test that system within an environment simulating the temperatures and pressures expected over a full lunar day cycle on the lunar surface. The system is designed to be as flight-like as possible given resource and commercially available technology limitations. The RFC system is comprised of a fuel cell power system, a high pressure electrolysis system, fluidic and electronic balance of plant systems, avionics, power management and distribution system, and software. This technical memorandum discusses components and subsystems that present challenges in developing flight ready RFCs. To remedy identified issues, functional application test plans are presented for components and subsystems primarily constructed with commercially available options due to the budget and schedule constraints of this ground technology demonstration project.

fuel cell↗
NASA NTRSDate not supplied

Update on Subsonic Single Aft Engine (SUSAN) Electrofan Trade Space Exploration

NASA is conducting an ongoing trade study analysis of the SUSAN Electrofan aircraft concept, which utilizes 20-MW-class electrified aircraft propulsion to enable propulsive, aerodynamic, and control benefits while retaining the range, speed, and size of typical narrow-body regional aircraft. The study is constrained by the ground rules of operating within the current airport and airspace infrastructure. This ongoing study seeks to find a configuration and combination of technologies that yield significant fuel burn and emissions benefits. Another key goal is to reduce cost per passenger mile. Currently, the study is focused on a configuration that utilizes jet A or sustainable aviation fuels, however, we plan to consider other fuel alternatives in the future. This presentation describes the progress in defining the architecture of the aircraft, engine, power system, control system, and initial understandings of the sensitivity of the potential configurations to technology assumptions based on key performance parameters. Additionally, progress towards definition and refinement of driving operational, economic, infrastructure, certification, and technical requirements is discussed.

Ralph H. Jansen↗
NASA NTRSDate not supplied

Thermal Requirements for Design and Analysis of Subsonic Single Aft Engine (SUSAN) Research Aircraft

The purpose of this paper is to define a set of thermal requirements which can be used for conceptual design studies of the Subsonic Single Aft eNgine (SUSAN) aircraft and the early design phases of a 25% scale flight research aircraft. SUSAN presents an architecture for a subsonic regional jet transport aircraft coupling a single turbofan engine to an electrified aircraft propulsion system (EAP). NASA, military, FAA, and commercial standards and guidance on the design and analysis of thermal management systems for aircraft are reviewed and summarized. The approach toward using these sources to develop the SUSAN thermal requirements is described. These requirements address the definition of the thermal environment, the design requirements for certain components that interface with the thermal management system, and thermal analysis margins.

Subsonic Single Aft Engine↗
NASA NTRSDate not supplied

Cryogenic Vacuum Chamber Testing of A Conductively-Cooled, High Temperature Superconducting Rotor for a 1.4 MW Electric Machine for Aeronautics Applications

This paper presents the second ever demonstration of a superconducting rotor cooled only via conductive connection to a cryocooler, i.e., without pumped or solid cryogens. The fullscale rotor was operated statically in its intended environment – about 1e-3 torr vacuum with only conductive cooling through mechanical connections to a cryocooler contained on the rotor. Stable operation of the rotor in a representative magnetic environment was demonstrated up to its rated direct current (57.2 A) and the designed temperature limit for the superconductor (62 K). Additional electrical measurements increased confidence that the superconducting coils functioned as intended. A collection of steady state temperature distributions was measured at operating and non-operating conditions. In all but one case, the observed temperature gradient between the cold tip and superconducting coils satisfies the design but with little margin. Opportunities to reduce the gradient are identified.

Electrified aircraft propulsion↗
NASA NTRSDate not supplied

Thermal Design, Analysis, and Testing of a Conductively-Cooled, High Temperature Superconducting Rotor for a 1.4 MW Electric Machine for Aeronautics Applications

This presentation covers the second ever demonstration of a superconducting rotor cooled only via conductive connection to a cryocooler, i.e., without pumped or solid cryogens. The full-scale rotor was operated statically in its intended environment – about 1e-3 torr vacuum with only conductive cooling through mechanical connections to a cryocooler contained on the rotor. Stable operation of the rotor in a representative magnetic environment was demonstrated up to its rated direct current (57.2 A) and the designed temperature limit for the superconductor (62 K). In all but one case, the observed temperature gradient between the cold tip and superconducting coils satisfies the design but with little margin. Thermal modeling and correlation with test data is presented identifying the areas of largest discrepancy. Opportunities to reduce the temperature gradient are identified.

electrified aircraft propulsion↗
NASA NTRSDate not supplied

NASA’s Quiet Electric ENgines (QUEEN): Summary of the QUEEN V2 Test

A liquid-cooled electric ducted fan system was designed, built, and tested at the NASA Glenn Research Center. Main components of the system include a Commercial-Off- the-Shelf (COTS) fan and motor, and a custom-designed heat exchanger integrated into the fan duct. Fan speed, thrust, and cooling system thermal performance was measured in this static ground test of the propulsor. This propulsor prototype is one of NASA’s Quiet Electric ENgines (QUEENs) and is designated the ‘QUEEN V2.’ The Quiet Electric Engines are being developed for the 25% scale model of the Subsonic Aft Engine (SUSAN) Flight Research Vehicle and are intended to explore the potential of distributed electric propulsion for regional single-aisle aircraft. This test demonstrated the functionality of the QUEEN V2, quantified the thrust produced by the electrofan, and characterized the electrical and thermal performance of the system. Lessons learned will be used to guide development of future QUEEN prototypes.

Aeronautics-General↗